Technical Specifications Each Bloom System is an integrated system comprised of a fuel cell stack assembly and associated balance of plant components that converts a fuel into electricity using electrochemical means that (i) has a Nameplate Capacity of at least 0.5 kilowatts of electricity using an electrochemical process and (ii) has an electricity-only generation efficiency greater than thirty percent (30%).
Listing and Maintenance Requirements The Common Stock is registered pursuant to Section 12(b) or 12(g) of the Exchange Act, and the Company has taken no action designed to, or which to its knowledge is likely to have the effect of, terminating the registration of the Common Stock under the Exchange Act nor has the Company received any notification that the Commission is contemplating terminating such registration. The Company has not, in the 12 months preceding the date hereof, received notice from any Trading Market on which the Common Stock is or has been listed or quoted to the effect that the Company is not in compliance with the listing or maintenance requirements of such Trading Market. The Company is, and has no reason to believe that it will not in the foreseeable future continue to be, in compliance with all such listing and maintenance requirements.
Support and Maintenance RSA agrees to provide the maintenance and support specified in this Support Agreement and You agree to pay RSA's then-current annual support fee ("Support Fee").
Quality Specifications SANMINA-SCI shall comply with the quality specifications set forth in its Quality Manual, incorporated by reference herein, a copy of which is available from SANMINA-SCI upon request.
Servicing and Maintenance Standards The Servicer shall, on behalf of the Issuer:
Statement of Work Independently and not as an agent of the Government, the Contractor shall furnish all the necessary services, qualified personnel, material, equipment, and facilities, not otherwise provided by the Government as needed to perform the Statement of Work, SECTION J, ATTACHMENT 1, April 30, 2004, attached hereto and made a part of this contract.
Maintenance and Support Services Distributor shall provide Maintenance and Support Services to all of its Customers of Licensed Software as set forth in Sections 3.4(a) and 3.4(b) below. Distributor may require Customers to provide the own First-Line Support: however, in no event shall Siebel be responsible for First-Line or Second-Line Support. Subject to Distributor's payment of the Maintenance Fees set forth in EXHIBIT A Siebel shall provide Third-Line Support to Distributor in accordance with Siebel's then current Maintenance and Support Services Policy. Distributor shall be responsible for all support related to the Value Added Offering.
Changes to Specifications All Specifications and any changes thereto agreed to by the parties from time to time shall be in writing, dated and signed by the parties. Any change to the Process shall be deemed a Specification change. No change in the Specifications shall be implemented by Catalent, whether requested by Client or requested or required by any Regulatory Authority, until the parties have agreed in writing to such change, the implementation date of such change, and any increase or decrease in costs, expenses or fees associated with such change (including any change to Unit Pricing). Catalent shall respond promptly to any request made by Client for a change in the Specifications, and both parties shall use commercially reasonable, good faith efforts to agree to the terms of such change in a timely manner. As soon as possible after a request is made for any change in Specifications, Catalent shall notify Client of the costs associated with such change and shall provide such supporting documentation as Client may reasonably require. Client shall pay all costs associated with such agreed upon changes. If there is a conflict between the terms of this Agreement and the terms of the Specifications, this Agreement shall control. Catalent reserves the right to postpone effecting changes to the Specifications until such time as the parties agree to and execute the required written amendment.
USE AND MAINTENANCE Except as may be otherwise specified on any Schedule, (a) Lessee shall (1) use the Equipment solely in the continental United States and in the conduct of its business, for the purpose for which the Equipment was designed, in a careful and proper manner, and shall not permanently discontinue use of the Equipment; (2) operate, maintain, service and repair the Equipment, and maintain all records and other materials relating thereto, (A) in accordance and consistent with (i) all maintenance and operating manuals or service agreements, whenever furnished or entered into, including any subsequent amendments or replacements thereof, issued by the supplier or service provider, (ii) the requirements of all applicable insurance policies, (iii) manufacturer’s recommendations, (iv) the original purchase agreement under which such Equipment was acquired, so as to preserve all of Lessee’s and Lessor’s rights thereunder, including all rights to any warranties, indemnities or other rights or remedies, as and if applicable, (v) all applicable laws, and (vi) the prudent practice of other similar companies in the same business as Lessee, but in any event, to no lesser standard than that employed by Lessee for comparable equipment owned or leased by it; and (B) without limiting the foregoing, so as to cause the Equipment to be in good repair and operating condition and in at least the same condition as when delivered to Lessee hereunder, except for ordinary wear and tear resulting despite Lessee's full compliance with the terms hereof; (3) provide written notice to Lessor not less than thirty (30) days after any change of the location of any Equipment (or the location of the principal garage of any Equipment, to the extent that such Equipment is mobile equipment) as specified in the Schedule; and (4) not attach or incorporate the Equipment into any property except for other Equipment in such a manner that the Equipment may be deemed to have become an accession to or a part of such other property. (b) Within a reasonable time, Lessee will replace any parts of the Equipment which become worn out, lost, destroyed, damaged beyond repair or otherwise unfit for use, by new or reconditioned replacement parts which are free and clear of all Liens and have a value, utility and remaining useful life at least equal to the parts replaced (assuming that they were in the condition required by this Lease). Any modification or addition to the Equipment that is required by this Lease shall be made by Lessee. An interest in all such parts, modifications and additions to the Equipment immediately shall vest in Lessor, without any further action by Lessor or any other person, and they shall be deemed incorporated in the Equipment for all purposes of the related Schedule. Unless replaced in accordance with this Section, Lessee shall not remove any parts originally or from time to time attached to the Equipment, if such parts are essential to the operation of the Equipment, are required by any other provision of this Lease or cannot be detached from the Equipment without interfering with the operation of the Equipment or adversely affecting the value, utility and remaining useful life which the Equipment would have had without the addition of such parts. Except as permitted in this Section, Lessee shall not make any material alterations to the Equipment. (c) Lessee shall afford Lessor and/or its designated representatives immediate access to the premises where the Equipment is located for the purpose of inspecting and appraising such Equipment and all applicable maintenance or other records relating thereto at any time during normal business hours, at Lessee’s sole cost and expense. If any discrepancies are found as they pertain to the general condition of the Equipment, Lessor will communicate these discrepancies to Lessee in writing. Lessee shall then have thirty (30) days to rectify these discrepancies at its sole expense. Lessee shall pay all expenses of a re-inspection by Lessor’s appointed representative, including travel costs.
Installation and Maintenance of Meters The Servicer shall cause to be installed, replaced and maintained meters in accordance with the Servicer Policies and Practices.
