Inscriptions. 2.3.1. Filament lamps submitted for approval shall bear on the cap or bulb2:
2.3.1.1. The trade name or xxxx of the applicant;
2.3.1.2. The rated voltage. However, for filament lamps for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked;
2.3.1.3. The international designation of the relevant category. The wattage character "W" of this designation need not be marked when the maximum allowed bulb diameter of the filament lamp type does not exceed 7.5 mm;
2.3.1.4. The rated wattage (in the sequence, high wattage/low wattage filament for dual-filament lamps); this need not be indicated separately if it is part of the international designation of the relevant filament lamp category;
2.3.1.5. A space of sufficient size to accommodate the approval xxxx.
2.3.2. The space mentioned in paragraph 2.3.1.5. above shall be indicated in the drawings accompanying the application for approval.
2.3.3. Halogen filament lamps meeting the requirements of paragraph 3.7. below shall be marked with a "U".
2.3.4. Inscriptions other than those covered by paragraphs 2.3.1. and 2.4.3. may be affixed, on the condition that they do not adversely affect the luminous characteristics.
Inscriptions. 2.3.1. Filament lLight sources submitted for approval shall bear on the cap or bulb2:
2.3.1.1. The trade name or xxxx of the applicant;
2.3.1.2. The rated voltage. However, for filament light sources for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked;
2.3.1.3. The international designation of the relevant category. The wattage character "W" of this designation need not be marked when if the maximum allowed bulb diameter of the filament light source type does not exceed 7.5 mm;
2.3.1.4. The rated wattage (in the sequence, high wattage/low wattage filament for dual-filament light sources); this need not be indicated separately if it is part of the international designation of the relevant filament light source category;
2.3.1.5. A space of sufficient size to accommodate the approval xxxx;
2.3.1.6. In the case of LED replacement light sources, the following symbol3: " .
2.3.2. The space mentioned in paragraph 2.3.1.5. above shall be indicated in the drawings accompanying the application for approval.
2.3.3. Halogen filament light sources meeting the requirements of paragraph 3.3.47. below shall be marked with a "U".
2.3.4. LED replacement light sources shall be marked “LEDr”. This xxxx shall be placed after or below the designation of the relevant LED replacement light source category separated by a single character space or line space.
2.3.5. In the case of electrical/electronic controls not integrated with the LED replacement light source, the controls [used for the type approval] shall be marked with [type and trade xxxx identification and with the rated voltage and wattage, as indicated on the relevant lamp data sheet,] [as well as the category designation(s) and approval code(s) of the LED replacement light source(s) approved with these electrical/electronic controls].
Inscriptions. 2.3.1. Gas-discharge light sources submitted for approval shall bear on the cap or bulb:
2.3.1.1. The trade name or xxxx of the applicant;
2.3.1.2. The international designation of the relevant category;
2.3.1.3. The rated wattage; this need not to be indicated separately if it is part of the international designation of the relevant category;
2.3.1.4. A space of sufficient size to accommodate the approval xxxx.
2.3.2. The space mentioned in paragraph 2.3.1.4. above shall be indicated in the drawings accompanying the application for approval.
2.3.3. Other inscriptions than those covered by paragraphs 2.3.1. above and 2.4.4. below may be affixed on the cap.
2.3.4. In case the ballast is not integrated with the light source, the ballast used for the type approval of the light source shall be marked with type and trade xxxx identification and with the rated voltage and wattage, as indicated on the relevant lamp data sheet.
Inscriptions. 2.3.1. Filament lLight sources submitted for approval shall bear on the cap or bulb2:
2.3.1.1. The trade name or xxxx of the applicant;
2.3.1.2. The rated voltage. However, for filament light sources for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked;
2.3.1.3. The international designation of the relevant category. The wattage character "W" of this designation need not be marked when if the maximum allowed bulb diameter of the filament light source type does not exceed 7.5 mm;
2.3.1.4. The rated wattage in the case of a filament light source, (in the sequence, high wattage/low wattage filament for dual-filament light sources); this need not be indicated separately if it is part of the international designation of the relevant filament light source category;
2.3.1.5. The character “L” in the case of a low-power LED replacement light source type; this xxxx shall be placed after or below the “LEDr” xxxx as in paragraph 2.3.4. separated by a single character space or line space
Inscriptions. 2.3.1. Gas-discharge light sources submitted for approval shall bear on the cap or bulb:
2.3.1.1. the trade name or xxxx of the applicant;
2.3.1.2. the international designation of the relevant category;
2.3.1.3. the rated wattage; this need not to be indicated separately if it is part of the international designation of the relevant category;
Inscriptions. 2.3.1. LED light sources submitted for approval shall bear on the cap:
2.3.1.1. The trade name or mark of the applicant;
2.3.1.2. The rated voltage;
2.3.1.3. The designation of the relevant category;
2.3.1.4. A space of sufficient size to accommodate the approval mark.
2.3.1.5. In the case of LED substitute light sources, the following symbol1:
2.3.2. The space mentioned in paragraph 2.3.1.4. above shall be indicated in the drawings accompanying the application for approval.
2.3.3. Inscriptions other than those covered by paragraphs 2.3.1. and 2.4.4. may be affixed, on the condition that they do not adversely affect the luminous characteristics.
Inscriptions. 2.3.1. LED light sources submitted for approval shall bear on the cap:
2.3.1.1. The trade name or xxxx of the applicant;
2.3.1.2. The rated voltage;
2.3.1.3. The designation of the relevant category;
2.3.1.4. A space of sufficient size to accommodate the approval xxxx.
2.3.2. The space mentioned in paragraph 2.3.1.4. above shall be indicated in the drawings accompanying the application for approval.
2.3.3. Inscriptions other than those covered by paragraphs 2.3.1. and 2.4.4. may be affixed, on the condition that they do not adversely affect the luminous characteristics.
Inscriptions. 2.3.1. Light sources submitted for approval shall bear:4
2.3.1.1. The trade name or mark of the applicant;
2.3.1.2. The rated voltage. However, for light sources for which only a 12 V type is standardised and the maximum allowed bulb diameter of which does not exceed 7.5 mm, the rated voltage need not be marked;
2.3.1.3. The designation of the relevant category. The wattage character "W" of this designation need not be marked if the maximum allowed bulb diameter of the light source type does not exceed 7.5 mm;
2.3.1.4. The rated wattage in the case of a filament light source, (in the sequence, high wattage/low wattage filament for dual-filament light sources); this need not be indicated separately if it is part of the designation of the relevant filament light source category;
2.3.1.5. The character "ͰE "5 in the case of a high-efficiency LED replacement light source; this mark shall be placed before the truncated circle according to paragraph 2.4.3.1., separated by a single character space.
2.3.1.6. A space of sufficient size to accommodate the approval mark;
2.3.1.7. In the case of a LED replacement light sources for which at least one of the conditions in paragraph 2.2.
2.2.2. applies, the following symbol:6 4 The luminous characteristics shall not be adversely affected.
Inscriptions. Engraving shall be of a uniform size, font, and composition prescribed by the Columbarium Board. The Purchaser or representative(s) or assigns of the Purchaser or the deceased is/are responsible for providing RUMC with the legal names and dates for birth and death of the deceased. Each niche will be Page. 6 Columbarium at Riverchase United Methodist Church 6-1-16 inscribed only with the name of the deceased, date of birth, and date of death. No other inscriptions or designations will be permitted.
Inscriptions. Les étudiants provenant du « Dipartimento di Lettere-Lingue, Letterature e Civiltà antiche e moderne » de Pérouse qui souhaitent suivre le cursus « Etudes italiennes et Histoire de l’art » devront être dûment inscrits aux cours de xxxxxx xxxxxxxxxx en «Italianistica e Storia Europea» (LM-14) ou bien en «Archeologia e Storia dell’Arte» (Classe LM-2 LM-89) et avoir une connaissance adéquate de la langue française (B2) vérifiée par l’université d’origine. Lors de leur séjour à l’Université de Tours, ils devront être dûment inscrits au Master « Etudes italiennes et Histoire de l’art » et ils devront acquérir un minimum de 40 CFU/ECTS. Les étudiants provenant de l’Université de Tours qui souhaitent poursuivre leur cursus dans le cadre du Dipartimento di « Lettere Lingue, Letterature e Civiltà antiche e moderne » de l’Università degli Studi di Perugia devront être dûment inscrits au Master « Etudes italiennes et Histoire de l’art » et avoir une connaissance adéquate de la langue italienne contrôlée par l’université d’origine. Lors de leur séjour à l’Università degli Studi di Perugia, ils devront être dûment inscrits au cursus de xxxxxx xxxxxxxxxx en « Italianistica et Storia europea » (LM-14) ou en « Archeologia e storia dell’arte » (LM-2 LM-89) et devront choisir un des cursus proposés et valider un minimum de 40 CFU/ECTS.
