Jacking Sample Clauses

Jacking. Follow these requirements when jacking:
AutoNDA by SimpleDocs
Jacking. It shall be possible to safely xxxx up the vehicle at curb weight, with a common 10-ton floor xxxx without special adapter, when a tire or dual set is completely flat and the vehicle is on a level, hard surface, without crawling under any portion of the vehicle. Jacking from a single point shall permit raising the vehicle sufficiently high to remove and reinstall a wheel and tire assembly. Jacking pads located on the body, axle or suspension near the wheels shall permit easy and safe jacking with the flat tire or dual set on a 6-inch-high run-up block not wider than a single tire. Jacking and changing any one tire shall be completed by a 2M mechanic helper in less than 30 minutes from the time the vehicle is approached. The vehicle shall withstand such jacking at any one or any combination of wheel locations without permanent deformation or damage. Jacking pads shall be painted safety yellow for ease of identification.

Related to Jacking

  • Pruning Nondestructive thinning of lateral branches to enhance views or trimming, shaping, thinning or pruning of a tree necessary to its health and growth is allowed, consistent with the following standards:

  • Fittings 3.2.1 Landing gear support structure and attachment fitting

  • Blasting Blasting shall be permitted only for road construction purposes unless advance permission is obtained from Forest Service. Whenever the Industrial Fire Precaution Level is II or greater, a fire security person equipped with a long handled round point No. 0 or larger shovel and a 5 gallon backpack pump can filled with water, will stay at location of blast for 1 hour after blasting is done. Blasting may be suspended by Forest Service, in areas of high rate of spread and resistance to control. Fuses shall not be used for blasting. Explosive cords shall not be used without permission of Forest Service, which may specify conditions under which such explosives may be used and precautions to be taken.

  • Welding Welding and use of cutting torches or cutoff saws will be permitted only in areas that have been cleared or are free of all material capable of carrying fire. Flammable debris and vegetation must be removed from within a minimum 10-foot radius of all welding and cutting operations. A shovel and a 5-gallon standard backpack water container filled and with handpump attached shall be immediately available for use in the event of a fire start. C8.212 – MARKET-RELATED CONTRACT TERM ADDITION (11/08). The term of this contract may be adjusted when a drastic reduction in wood product prices has occurred in accordance with 36 CFR 223.52. The Producer Price Index used to determine when a drastic reduction in price has occurred is stated in A20. Purchaser will be notified whenever the Chief determines that a drastic reduction in wood product prices has occurred. If the drastic reduction criteria specified in 36 CFR 223.52 are met for 2 consecutive calendar quarters, after contract award date, Contracting Officer will add 1 year to the contract term, upon Purchaser’s written request. For each additional consecutive quarter such a drastic reduction occurs, Contracting Officer will, upon written request, add an additional 3 months to the term during Normal Operating Season, except that no single 3-month addition shall extend the term of the contract by more than one year. Contracting Officer must receive Purchaser’s written request for a market-related contract term addition before the expiration of this contract. No more than 3 years shall be added to a contract's term by market-related contract term addition unless the following conditions are met:

  • Staging In addition to the staging categories listed in paragraph 1 of Annex 2-A, this Schedule contains staging categories 20-A, 20-B, PR-1 and PR-130:

  • Brakes Master cylinder, wheel cylinders, hydraulic lines and fittings, power booster and brake callipers. Excludes linings, pads, drums and discs.

  • Scratches (Q) appliance malfunctions and any resultant leak there from; (R) any stain, soiling or damage resulting from everyday use or which has built up over time, e.g. hair, body or suntan oils and/or lotions; (S) signs of soiling include darkened areas where the body comes into contact with the furniture (these darkened areas are signs of soil build-up, which is not covered); (T) general maintenance and overall cleaning of the furniture is the consumer’s responsibility; (U) damage due to harsh or corrosive chemicals; (V) acids, including without limitation, dyes and inks (except ballpoint), plant food and fertilizer and bleach, gum; (W) any non-operating part or decorative parts such as hinges, knobs, handles, or shelves; (X) coverage under another insurance program; (Y) delivery and/or redelivery and/or loss or damage to the Covered Product while in the course of transit; (Z) design deficiency; (AA) fabrics with “X” cleaning codes and non-colorfast fabrics and leathers; (AB) odors; (AC) variation of the color, or graining of wood or wood products, marble or leather; (AD) split leathers used in seat cushions, back cushions or top or inside arm areas; (AE) natural markings on leather, such as, healed scars, insect bites, brand marks or wrinkles, or suede, and leathers with embossed patterns other than those stimulating natural cowhide; (AF) non- bovine leathers, and other buffed leathers; (AG) stains, color loss or damage resulting from cleaning methods or products (detergents, abrasives or other harsh cleaning agents) other than those recommended by the furniture manufacturer; (AH) stone or sand abrasion; (AI) loss or damage resulting from: pre-existing conditions known to You; (AJ) wear related issues, such as but not limited to, fading, wear, seam separation, stress tears, loss of foam resiliency, pilling or fraying of any fabric on all types of furniture; (AK) color loss or cracking and peeling on any leather or vinyl; (AL) splits or bi-cast leather; (AM) furniture that is used for commercial, institutional, outdoor or rental purposes; (AN) Customer’s Own Material furniture; (AO) wicker, rattan, and teakwood furniture; (AP) massage chairs; (AQ) stains or damage to suede, split-grain leather hide or exotic leathers; (AR) manufacturer quality issues such as stress tears, fabric flaws, fading, color loss or change, loss of foam or resiliency, cracking and peeling of leather or vinyl, natural leather markings, and defects in design and workmanship; (AS) Stains or damage that occur during assembly, delivery, installation, before furniture is delivered to your residence, while the furniture is located outside of your residence, while the furniture is in storage or being moved to or from storage or between residences; (AT) Wear & Tear caused by repeated use such as scuffing, soiling, hair/body oil, perspiration, surface abrasions, pilling or fraying of fabric, loose joints; (AU) Stains or damage covered under any manufacturer warranty, recall, homeowner, renter or other insurance policy; (AV) Stains or damage caused by structural problems, appliance malfunctions, Acts of God or natural disasters, theft, vandalism or illegal activity (AW) Stains or damage caused by independent contractors Specific to Home Automation: In additional to the exclusions listed above, this Agreement does not cover any loss, repairs or damage caused by or resulting from: (A) pre-existing conditions incurred or known to you (pre-existing means a condition prior to Plan issuance); (B) any repair covered by a manufacturer’s warranty or any insurance; (C) installation, or improper installation; or improper installation of customer replaceable components, modules, parts or peripherals; (D) damage or failure due to causes beyond our control such as environmental conditions, exposure to weather conditions or acts of nature including, but not limited to: fire, floods, smoke, sand, dirt, lightning, moisture, water damage, freezes, storms, wind, windstorm, hail, earthquake, animal or insect infestation, etc.; (E) damage or failure caused by riot, nuclear radiation, war, hostile action, or radioactive contamination, etc.; (F) battery failure or leakage; (G) collision, collapse, or explosion; (H) liquid spillage of any kind; (I) signal reception, transmission problems resulting from external causes, interruption of electrical service, loss of power, improper use of electrical/power, power “brown-out”, power overload or power surge (unless covered in the Special Features section of this document); (J) neglect, misuse, abuse, intentional damage, malicious mischief, theft, mysterious disappearance, vandalism or accidental damage; damage cause by dropping (K) rust, corrosion, warping, bending, etc.; (L) damage, warping, bending or rusting of any kind to the housing, cabinetry, outside casing or frame of the product; (M) any non-operating part, including but not limited to plastic, or decorative parts such as hinges, knobs, door liners, glass, handles, masks, rack rollers, shelves, etc.; (N) loss of or repair to components within the product not originally covered by the manufacturer’s warranty; (O) failure to product attachments not provided by the manufacturer or included in the original sale;

  • Hazing Hazing is a process, based on tradition that is used by groups to maintain a hierarchy (i.e., a pecking order) within the group. Regardless of consent, the rituals require individuals to engage in activities that are physically and/or psychologically stressful. These activities can be humiliating, demeaning, intimidating, and exhausting, all of which results in physical or emotional discomfort. Hazing is about group dynamics and proving one’s worthiness to become a member of a specific group. The newcomer, or victim, is hazed. Once accepted by the group, the victim may become a bystander, watch others get hazed, achieve senior status, and ultimately become a perpetrator of hazing. In New Jersey, hazing is a separate criminal offense under N.J.S.A. 2C:40-3. School officials should be aware that hazing which involves the participation of a coach or a teacher may also constitute child abuse. Hazing may also involve other predicate crimes, such as sexual assault. Hazing may also constitute HIB. As noted in Article 4.4.2, although HIB is not a separately defined criminal offense, the conduct that constitutes bullying may constitute one or more criminal or disorderly person offenses, including assault, harassment, threats, robbery and sexual offenses.

  • Grooming The parties agree that the agency shall have the right to set reasonable and professional grooming standards for its employees. The agency and state agree to consult with the Association in the development of said grooming standards.

  • Wash all machine-washable bedding, drapes, and clothing, on the hottest water temperature and dry on the highest heat setting. Items that cannot be washed must be taken to a dry cleaner who MUST be informed of the issue. You must safely discard ALL items that cannot be decontaminated.

Time is Money Join Law Insider Premium to draft better contracts faster.