Common use of Means Clause in Contracts

Means. Please note, not all items will have an exact answer, nor will every assembly total 100%. Please provide a response, based on your best interpretations of the contract documents, to ALL items listed. If you have questions concerning the assemblies identified, please contact a Project Controls Specialist - Cost at (000) 000-0000. Project No. & Title _______ - _______ ______________________________________________________ Project Stage Title ______________________________________________________ New Renovated Gross Square Feet (Not including basement) __________________ ___________________ Assignable Square Feet (Not including basement) __________________ ___________________ Number of Rooms __________________ Number of Stories At Grade & Above __________________ Average Story Height At Grade & Above (ft) __________________ Number of Basement Levels & Gross Square Feet 0 __________________ Building Perimeter (Lft.)* __________________ Type of Foundation * ____________________________________ Primary Superstructure System * ____________________________________ Primary Exterior Closure & Percent * ____________________________________ ____ Secondary ____________________________________ ____ Percentage of Exterior Glass / Glazing __________________ Primary Roofing System * ____________________________________ Primary Interior Partition Construction & Percent * ____________________________________ ____ Secondary * ____________________________________ ____ Number of Doors (A pair of doors equals two doors) __________________ Primary Interior Flooring & Percent * ____________________________________ ____ Secondary * ____________________________________ ____ Primary Interior Ceiling Construction & Percent * ____________________________________ ____ Secondary * ____________________________________ ____ Type of Conveying System & Number of Units * __________________ Number of Plumbing Fixtures Installed 0 __________________ Building HVAC CFM Requirements __________________ * Refer to Page 2 for definitions & lists. Please use the definitions and lists below to complete the questions on the Exhibit L. If a project does not have an assembly (i.e.: basement) then insert “None” into the appropriate blank. If a project has an existing assembly that is modified or repaired then insert “Modify” or “Repair”, however, if a project scope does not modify or repair an existing assembly then insert “Existing” into the appropriate blank.

Means. Please note, not all items will have an exact answer, nor will every assembly total 100%. Please provide a response, based on your best interpretations of the contract documents, to ALL items listed. If you have questions concerning the assemblies identified, please contact a Project Controls Specialist - Cost at (000) 000-0000. Project No. & Title _______ - _______ ______________________________________________________ Project Stage Title ______________________________________________________ New Renovated Gross Square Feet (Not including basement) __________________ ___________________ Assignable Square Feet (Not including basement) __________________ ___________________ Number of Rooms __________________ Number of Stories At Grade & Above __________________ Average Story Height At Grade & Above (ft) __________________ Number of Basement Levels & Gross Square Feet 0 __________________ Building Perimeter (Lft.)* __________________ Type of Foundation * ____________________________________ Primary Superstructure System * ____________________________________ Primary Exterior Closure & Percent * ____________________________________ ____ Secondary ____________________________________ ____ Percentage of Exterior Glass / Glazing __________________ Primary Roofing System * ____________________________________ Primary Interior Partition Construction & Percent * ____________________________________ ____ Secondary * ____________________________________ ____ Number of Doors (A pair of doors equals two doors) __________________ Primary Interior Flooring & Percent * ____________________________________ ____ Secondary * ____________________________________ ____ Primary Interior Ceiling Construction & Percent * ____________________________________ ____ Secondary * ____________________________________ ____ Type of Conveying System & Number of Units * __________________ Number of Plumbing Fixtures Installed 0 __________________ Building HVAC CFM Requirements __________________ * Refer to Page 2 for definitions & lists. Please 0Please use the definitions and lists below to complete the questions on the Exhibit L. If a project does not have an assembly (i.e.: basement) then insert “None” into the appropriate blank. If a project has an existing assembly that is modified or repaired then insert “Modify” or “Repair”, however, if a project scope does not modify or repair an existing assembly then insert “Existing” into the appropriate blank.

Means. Please note, not all items will have an exact answer, nor will every assembly total 100%. Please provide a response, based on your best interpretations of the contract documents, to ALL items listed. If you have questions concerning the assemblies identified, please contact a Project Controls Specialist - Cost at (000) 000-0000. Project No. & Title _______ - _______ ______________________________________________________ Project Stage Title ______________________________________________________ New Renovated Gross Square Feet (Not including basement) __________________ ___________________ Assignable Square Feet (Not including basement) __________________ ___________________ Number of Rooms __________________ Number of Stories At Grade & Above __________________ Average Story Height At Grade & Above (ft) __________________ Number of Basement Levels & Gross Square Feet 0 __________________ Building Perimeter (Lft.)* __________________ Type of Foundation * ____________________________________ Primary Superstructure System * ____________________________________ Primary Exterior Closure & Percent * ____________________________________ ____ Secondary Secondary* ____________________________________ ____ Percentage of Exterior Glass / Glazing __________________ Primary Roofing System * ____________________________________ Primary Interior Partition Construction & Percent * ____________________________________ ____ Secondary * ____________________________________ ____ Number of Doors (A pair of doors equals two doors) __________________ Primary Interior Flooring & Percent * ____________________________________ ____ Secondary * ____________________________________ ____ Primary Interior Ceiling Construction & Percent * ____________________________________ ____ Secondary * ____________________________________ ____ Type of Conveying System & Number of Units * __________________ Number of Plumbing Fixtures Installed 0 __________________ Building HVAC CFM Requirements __________________ * Refer to Page 2 for definitions & lists. Please 0Please use the definitions and lists below to complete the questions on the Exhibit L. If a project does not have an assembly (i.e.: basement) then insert “None” into the appropriate blank. If a project has an existing assembly that is modified or repaired then insert “Modify” or “Repair”, however, if a project scope does not modify or repair an existing assembly then insert “Existing” into the appropriate blank.