Year Limited Warranty Commercial/multi-resident Subject to the limitations and exclusions herein, and for the duration of the applicable Warranty Period of the Residential Warranty Holder or Commercial/ Multi-Resident Warranty Holder (as defined below), Xxxxxxxx Windows, Inc. and Simonton Industries, Inc. (hereinafter, “Simonton”), warrants that the Product will be free from non-conformities in material and workmanship. Xxxxxxxx will repair or replace any Product that fails to meet this Limited Warranty of a Residential Warranty Holder that is installed up to an elevation of not more than three stories (for Product installations over three stories contact Xxxxxxxx for warranty consideration); provided in either case, Operation of your Vinyl Windows and doors Along with being virtually maintenance free, your windows and doors have been designed and manufactured to be thermally efficient, aesthetically pleasing and easy to operate. Double Hung and Slider sash lift out; Casement sash open by turning the handle. to tilt in the operable sash on double Hung and Single Hung windows, you must: n Unlock the sash and raise (or lower) it approximately 4” above (or below) the frame. n Slide the tilt latches toward the cam lock and gently tilt the sash in. Always support tilted sash while cleaning. n When finished cleaning, tilt the sash up and snap the tilt latches into place. For safety, make sure the tilt latches are securely engaged. n If it becomes necessary to remove and reinsert the sash, tilt the sash inward to a 90-degree angle and lift the bottom of the sash up and out of the frame. To reinsert the sash into the frame, make sure both pivot bars (located at the bottom of the sash) are fully inserted into the balance shoes Xxxxxxxx may refund the purchase price (the lesser of the original Product/ to remove a Slider sash, simply: Balance Shoe component purchase price or the original catalog list price) if in Xxxxxxxx’x opinion such repair or replacement is not commercially practical or reasonable or cannot timely be made. This Limited Warranty is applicable to Products purchased and installed in the United States or Canada only. Warranty Period Lifetime (Vinyl) and 20 years (Hardware, Glass and Screens)
Warranty Period Except as may be otherwise specified or agreed, Contractor shall repair all defects in materials, equipment, or workmanship appearing within one year from the date of Substantial Completion of the Work. If Substantial Completion occurs by phase, then the warranty period for that the Work performed for each phase begins on the date of Substantial Completion of that phase, or as otherwise stipulated on the Certificate of Substantial Completion for the particular phase.
Xxxxx Period After payment of the first Dues, the Subscriber is entitled to a grace period of 30 days for the pay- ment of any Dues due. During this grace period, the Agreement will remain in force. However, the Sub- xxxxxxx will be liable for payment of Dues accruing during the period the Agreement continues in force.
Automatic Renewal Limitation for TIPS Sales No TIPS Sale may incorporate an automatic renewal clause that exceeds month to month terms with which the TIPS Member must comply. All renewal terms incorporated into a TIPS Sale Supplemental Agreement shall only be valid and enforceable when Vendor received written confirmation of acceptance of the renewal term from the TIPS Member for the specific renewal term. The purpose of this clause is to avoid a TIPS Member inadvertently renewing an Agreement during a period in which the governing body of the TIPS Member has not properly appropriated and budgeted the funds to satisfy the Agreement renewal. Any TIPS Sale Supplemental Agreement containing an “Automatic Renewal” clause that conflicts with these terms is rendered void and unenforceable.
Xxxxxx Limitation The Service reserves the right to refuse to pay any Xxxxxx to whom you may direct a payment. As required by applicable law, the Service will notify you promptly if it decides to refuse to pay a Xxxxxx designated by you. as set forth in Section 13 of the General Terms (Prohibited Payments) or an Exception Payment under this Agreement.
Warranty Periods All warranties begin to run from the date Material Completion is achieved.
Basic Equipment Warranty The Contractor warrants that all equipment rented or supplied under this Agreement shall be in good working order and shall conform to the needs specified by the Judicial Council. The Contractor shall immediately replace any inoperative equipment with operative equipment, or make all adjustments, repairs, and parts replacements required to maintain the equipment rented or supplied hereunder in working condition.
Benefit Waiting Period Allowance (a) An employee who qualifies for and takes leave pursuant to 21.1 or 21.2 and is required by Employment Insurance to serve a one-week waiting period for Employment Insurance Maternity/Parental benefits, shall be paid a leave allowance equivalent to one week at 85% of the employee's basic pay.
Venue Limitation for TIPS Sales Vendor agrees that if any "Venue" provision is included in any TIPS Sale Agreement/contract between Vendor and a TIPS Member, that clause must provide that the "Venue" for any litigation or alternative dispute resolution shall be in the state and county where the TIPS Member operates unless the TIPS Member expressly agrees otherwise. Any TIPS Sale Supplemental Agreement containing a “Venue” clause that conflicts with these terms is rendered void and unenforceable.
Correction Period (1) End of correction period. The last day of the correction period for an Operational Failure is the last day of the second plan year following the plan year for which the failure occurred. However, in the case of a failure to satisfy the requirements of § 401(k)(3), 401(m)(2), or 401(m)(9), the correction period does not end until the last day of the second plan year following the plan year that includes the last day of the additional period for correction permitted under § 401(k)(8) or 401(m)(6). If a 403(b) Plan does not have a plan year, the plan year is deemed to be the calendar year for purposes of this subsection.
