Overload A regular employee who works an overload in a given year shall receive no less than either:
Overload Teaching Paragraph 1: Overload teaching is that teaching conducted by a full-time classroom teacher teaching daily in a vacant position during his/her planning period.
Noise The Hirer shall ensure that the minimum of noise is made on arrival and departure, particularly late at night and early in the morning. The Hirer shall, if using sound amplification equipment, make use of any noise limitation device provided at the premises and comply with any other licensing condition for the premises.
Electrical Provide drawings for the following systems:
Scratches (Q) appliance malfunctions and any resultant leak there from; (R) any stain, soiling or damage resulting from everyday use or which has built up over time, e.g. hair, body or suntan oils and/or lotions; (S) signs of soiling include darkened areas where the body comes into contact with the furniture (these darkened areas are signs of soil build-up, which is not covered); (T) general maintenance and overall cleaning of the furniture is the consumer’s responsibility; (U) damage due to harsh or corrosive chemicals; (V) acids, including without limitation, dyes and inks (except ballpoint), plant food and fertilizer and bleach, gum; (W) any non-operating part or decorative parts such as hinges, knobs, handles, or shelves; (X) coverage under another insurance program; (Y) delivery and/or redelivery and/or loss or damage to the Covered Product while in the course of transit; (Z) design deficiency; (AA) fabrics with “X” cleaning codes and non-colorfast fabrics and leathers; (AB) odors; (AC) variation of the color, or graining of wood or wood products, marble or leather; (AD) split leathers used in seat cushions, back cushions or top or inside arm areas; (AE) natural markings on leather, such as, healed scars, insect bites, brand marks or wrinkles, or suede, and leathers with embossed patterns other than those stimulating natural cowhide; (AF) non- bovine leathers, and other buffed leathers; (AG) stains, color loss or damage resulting from cleaning methods or products (detergents, abrasives or other harsh cleaning agents) other than those recommended by the furniture manufacturer; (AH) stone or sand abrasion; (AI) loss or damage resulting from: pre-existing conditions known to You; (AJ) wear related issues, such as but not limited to, fading, wear, seam separation, stress tears, loss of foam resiliency, pilling or fraying of any fabric on all types of furniture; (AK) color loss or cracking and peeling on any leather or vinyl; (AL) splits or bi-cast leather; (AM) furniture that is used for commercial, institutional, outdoor or rental purposes; (AN) Customer’s Own Material furniture; (AO) wicker, rattan, and teakwood furniture; (AP) massage chairs; (AQ) stains or damage to suede, split-grain leather hide or exotic leathers; (AR) manufacturer quality issues such as stress tears, fabric flaws, fading, color loss or change, loss of foam or resiliency, cracking and peeling of leather or vinyl, natural leather markings, and defects in design and workmanship; (AS) Stains or damage that occur during assembly, delivery, installation, before furniture is delivered to your residence, while the furniture is located outside of your residence, while the furniture is in storage or being moved to or from storage or between residences; (AT) Wear & Tear caused by repeated use such as scuffing, soiling, hair/body oil, perspiration, surface abrasions, pilling or fraying of fabric, loose joints; (AU) Stains or damage covered under any manufacturer warranty, recall, homeowner, renter or other insurance policy; (AV) Stains or damage caused by structural problems, appliance malfunctions, Acts of God or natural disasters, theft, vandalism or illegal activity (AW) Stains or damage caused by independent contractors Specific to Home Automation: In additional to the exclusions listed above, this Agreement does not cover any loss, repairs or damage caused by or resulting from: (A) pre-existing conditions incurred or known to you (pre-existing means a condition prior to Plan issuance); (B) any repair covered by a manufacturer’s warranty or any insurance; (C) installation, or improper installation; or improper installation of customer replaceable components, modules, parts or peripherals; (D) damage or failure due to causes beyond our control such as environmental conditions, exposure to weather conditions or acts of nature including, but not limited to: fire, floods, smoke, sand, dirt, lightning, moisture, water damage, freezes, storms, wind, windstorm, hail, earthquake, animal or insect infestation, etc.; (E) damage or failure caused by riot, nuclear radiation, war, hostile action, or radioactive contamination, etc.; (F) battery failure or leakage; (G) collision, collapse, or explosion; (H) liquid spillage of any kind; (I) signal reception, transmission problems resulting from external causes, interruption of electrical service, loss of power, improper use of electrical/power, power “brown-out”, power overload or power surge (unless covered in the Special Features section of this document); (J) neglect, misuse, abuse, intentional damage, malicious mischief, theft, mysterious disappearance, vandalism or accidental damage; damage cause by dropping (K) rust, corrosion, warping, bending, etc.; (L) damage, warping, bending or rusting of any kind to the housing, cabinetry, outside casing or frame of the product; (M) any non-operating part, including but not limited to plastic, or decorative parts such as hinges, knobs, door liners, glass, handles, masks, rack rollers, shelves, etc.; (N) loss of or repair to components within the product not originally covered by the manufacturer’s warranty; (O) failure to product attachments not provided by the manufacturer or included in the original sale;
Lighting A system of fixtures providing or controlling the light sources used on or near the airport or within the airport buildings. The field lighting includes all luminous signals, markers, floodlights, and illuminating devices used on or near the airport or to aid in the operation of aircraft landing at, taking off from, or taxiing on the airport surface.
Overload Assignments (a) An overload assignment is defined as the assignment of duties in excess of the faculty member’s full-time appointment.
Smoke This peril means sudden and accidental damage from smoke, including the emission or puffback of smoke, soot, fumes or vapors from a boiler, furnace or related equipment. This peril does not include loss caused by smoke from agricultural smudging or industrial operations.
Illumination The Engineer shall refer to TxDOT’s Highway Illumination Manual and other deemed necessary State approved manuals for design of continuous lighting and safety lighting for all conventional, high-mast, and underpass lighting. The Engineer shall include safety lighting as part of each design on each flashing beacon and traffic signal. The Engineer shall provide a preliminary layout for initial review and approval by the State. The Engineer shall prepare circuit wiring diagrams showing the number of luminaries on each circuit, electrical conductors, length of runs, service pole assemblies. Underpass lighting must be used on all structures within each project. The Engineer shall integrate existing illumination within the project limits into the proposed design. The Engineer shall coordinate with the State to determine the location of proposed high- mast, conventional, and underpass lighting.
Glazing All new and replacement exterior windows shall have sealed, low emmissivity, insulating glass units which are manufactured by members of SIGMA and IGCC. Sealed insulating glass shall meet ASTM E774, class B. Glass shall be hermetically dual sealed, inert gas filled, double pane units with exterior 3/16” bronze float glass (IoE second surface), ½” air space, and interior 3/16” clear float glass. Insulated panels, if used, shall be 1” laminated panels equal to Xxxxx Industries architectural panels with a porcelain fused-on finish. Wired or clear fire-rated glass shall be UL approved. Safety glass shall be tempered or laminated, and shall meet ANSI 297.1 standard.
