Performance Standard Measurement Sample Clauses

Performance Standard Measurement. Contractor represents and warrants that it shall maintain the System, in whole and in part, to meet the Performance Standards. Contractor will conduct tests for measuring and certifying the achievement of the Performance Standards. Contractor must implement all testing, measurement and monitoring tools and procedures required to measure and report Contractor’s performance of the Services and System against the applicable Performance Standards. Such testing, measurement and monitoring must permit reporting at a level of detail sufficient to verify compliance with the Performance Standards, and will be subject to audit by AOC. Contractor will provide AOC with information and access to all information or work product produced by such tools and procedures upon request for purposes of verification.
Sample 1Sample 2
AutoNDA by SimpleDocs
Performance Standard Measurement. Contractor shall maintain the System, in whole and in part, to meet the Performance Standards in Exhibit C. Contractor will conduct tests for measuring and certifying the achievement of the Performance Standards. Contractor must implement all testing, measurement and monitoring tools and procedures required to measure and report Contractor’s performance of the Services and System against the applicable Performance Standards. Such testing, measurement and monitoring must permit reporting at a level of detail sufficient to verify compliance with the Performance Standards and will be subject to audit by HCA. Contractor will provide HCA with information and access to all information or Work Product produced by such tools and procedures within the timeframes set out in the Performance Standards and upon request for purposes of verification.
Sample 1
Performance Standard Measurement. Licensor shall maintain the System, in whole and in part, to meet all performance standards. Licensor will conduct tests for measuring and certifying the achievement of the performance standards. Licensor must implement all testing, measurement and monitoring tools and procedures required to measure and report Licensor’s performance of the System against the applicable Performance Standards. Such testing, measurement and monitoring must permit reporting at a level of detail sufficient to verify compliance with the Performance Standards and will be subject to audit by Licensee. Licensor will provide Licensee with information and access to all information or work product produced by such tools and procedures upon request for purposes of verification.
Sample 1
Performance Standard Measurement. Contractor shall maintain the WATRS, in whole and in part, to meet the Performance Standards. Contractor will conduct tests for measuring and certifying the achievement of the Performance Standards. Contractor must implement all testing, measurement and monitoring tools and procedures required to measure and report Contractor’s performance of the Services and the WATRS against the applicable Performance Standards. Such testing, measurement and monitoring must permit reporting at a level of detail sufficient to verify compliance with the Performance Standards, and will be subject to audit by DSHS. Contractor will provide DSHS with information and access to all information or work product produced by such tools and procedures upon request for purposes of verification.
Sample 1
Performance Standard Measurement. Contractor will conduct tests for measuring and certifying the achievement of the Performance Standards. Contractor must implement all testing, measurement and monitoring tools and procedures required to measure and report Contractor’s performance of the Services and System against the applicable Performance Standards. Such testing, measurement and monitoring must permit reporting at a level of detail sufficient to verify compliance with the Performance Standards, and will be subject to audit by State. Contractor will provide State with information and access to all information or work product produced by such tools and procedures upon request for purposes of verification.
Sample 1
Performance Standard Measurement. The County shall have the right to conduct performance load testing on the production instance of the Avatar PM and CWS installations on an annual basis for the first three years after Acceptance of the System. Contractor will warrant that the production instance will meet or exceed Performance Standards for Response Times defined in Exhibit C. County retains the right to conduct this load testing annually. The Contractor warranty is contingent on the County maintaining the installation of the System in accordance or in excess of the minimum requirements set forth by Contractor in Exhibit B for this installation.
Sample 1

Related to Performance Standard Measurement

  • Performance Standard Contractor shall perform all work hereunder in a manner consistent with the level of competency and standard of care normally observed by a person practicing in Contractor's profession. County has relied upon the professional ability and training of Contractor as a material inducement to enter into this Agreement. Contractor hereby agrees to provide all services under this Agreement in accordance with generally accepted professional practices and standards of care, as well as the requirements of applicable federal, state and local laws, it being understood that acceptance of Contractor’s work by County shall not operate as a waiver or release. If County determines that any of Contractor's work is not in accordance with such level of competency and standard of care, County, in its sole discretion, shall have the right to do any or all of the following: (a) require Contractor to meet with County to review the quality of the work and resolve matters of concern; (b) require Contractor to repeat the work at no additional charge until it is satisfactory; (c) terminate this Agreement pursuant to the provisions of Article 4; or (d) pursue any and all other remedies at law or in equity.

  • Performance Measurement Satisfactory performance of this Contract will be measured by:

  • Performance Standards The Contractor agrees to perform all tasks and provide deliverables as set forth in the Contract. The Department and the Customer will be entitled at all times, upon request, to be advised as to the status of work being done by the Contractor and of the details thereof.

  • PERFORMANCE MEASUREMENTS Upon a particular Commission’s issuance of an Order pertaining to Performance Measurements in a proceeding expressly applicable to all CLECs generally, BellSouth shall implement in that state such Performance Measurements as of the date specified by the Commission. Performance Measurements that have been Ordered in a particular state can currently be accessed via the internet at xxxx://xxxx.xxxxxxxxx.xxx. The following Service Quality Measurements (SQM) plan as it presently exists and as it may be modified in the future, is being included as the performance measurements currently in place for the state of Tennessee. At such time that the TRA issues a subsequent Order pertaining to Performance Measurements, such Performance Measurements shall supersede the SQM contained in the Agreement. BellSouth Service Quality Measurement Plan‌ (SQM) Tennessee Performance Metrics Measurement Descriptions Version 2.00 Issue Date: July 1, 2003 Introduction

  • Performance Levels (a) The Performance Levels which apply to the performance by the respective Parties of their obligations under this Agreement are set out in Part 1 of Schedule 5. A failure by either Party to achieve the relevant Performance Level will not constitute a breach of this Agreement and the only consequences of such failure as between the Parties shall be the consequences set out in this Clause 5.6.

  • Performance Schedule The Parties will perform their respective responsibilities in accordance with the Performance Schedule. By executing this Agreement, Customer authorizes Motorola to proceed with contract performance.

  • Usage Measurement Usage measurement for calls shall begin when answer supervision or equivalent Signaling System 7 (SS7) message is received from the terminating office and shall end at the time of call disconnect by the calling or called subscriber, whichever occurs first.

  • Performance Measures and Metrics This section outlines the performance measures and metrics upon which service under this SLA will be assessed. Shared Service Centers and Customers will negotiate the performance metric, frequency, customer and provider service responsibilities associated with each performance measure. Measurements of the Port of Seattle activities are critical to improving services and are the basis for cost recovery for services provided. The Port of Seattle and The Northwest Seaport Alliance have identified activities critical to meeting The NWSA’s business requirements and have agreed upon how these activities will be assessed.

  • Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.

  • Performance Measures The System Agency will monitor the Grantee’s performance of the requirements in Attachment A and compliance with the Contract’s terms and conditions.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!