PNGV Technical Targets Sample Clauses

PNGV Technical Targets. Fuel-Flexible Fuel Processors (Excludes fuel storage, includes controls, shift reactors, CO clean-up, heat exchangers) Calendar Year Characteristics Units 1997 2000 2004 Energy Efficiency % 70 75 80 Power Density W/L 400 600 750 Specific Power W/kg 400 600 750 Cost $/kW 50 30 10 Start-up to Full Power Min 2 1 0.5 Transient Response Sec 30 20 1.0 (time from 10 to 90% power) Emissions(a) less than Tier 2 less than Tier 2 less than Tier 2 Durability(b) Hours 1000 2000 5000 CO Content Steady State(c) ppm 100 10 1.0 CO Content Transient ppm 5000 500 100 H2S Content in Product Stream ppm 0 0 0 NH3 Content in Product Stream ppm less than 10 10 less than 10 Targets pertain to gasoline fuel and are consistent with those of the PNGV. Fuel processor efficiency = total fuel cell system efficiency/fuel cell stack system efficiency, where total fuel cell system efficiency accounts for thermal integration. high-volume production: 500,000 units per year. (a) Emission levels will comply with emission regulations projected to be in place when the technology is available for market introduction. (b) Time between catalyst replacement. (c) dependent on stack development (CO tolerance) progress. From Table 1 and the foregoing discussion, it is clear that desired performance characteristics of the PROX catalyst are as follows: o High activity towards oxidation of CO (and other potential contaminants such as NH3 and zero Epyx/SCi Confidential and Proprietary or near zero consumption of hydrogen (via oxidation, methanation, etc.) o No activity for reverse water gas shift reaction o Ability to operate with stoichiometric or near stoichiometric amounts of oxygen o High thermal and mechanical integrity/longevity o Ability for rapid startup, shut-down and transients o Ability to withstand intermittent operation o Heat transfer capability o High tolerance for contaminant(s) such as sulfur, chlorine, etc. o Ability to withstand reformate feed streams emanating from multiple fuels such as reformulated gasoline, natural gas, ethanol, etc.
Sample 1
AutoNDA by SimpleDocs

Related to PNGV Technical Targets

  • SHOP DRAWINGS, PRODUCT DATA AND SAMPLES 4.12.1 Shop Drawings are drawings, diagrams, schedules and other, data specially prepared for the Work by the Contractor or any Subcontractor, manufacturer, supplier or distributor to illustrate some portion of the Work. 4.12.2 Product Data are illustrations, standard schedules, performance charts, instructions, brochures, diagrams and other information furnished by the Contractor to illustrate a material, product or system for some portion of the Work. 4.12.3 Samples are physical examples which illustrate materials, equipment or workmanship and establish standards by which the Work will be judged. 4.12.4 The Contractor shall review, approve and submit, with reasonable promptness and in such sequence as to cause no delay in the Work or in the work of the State or any separate contractor, all Shop Drawings, Product Data and Samples required by the Contract Documents. 4.12.5 By approving and submitting Shop Drawings, Product Data and Samples, the Contractor represents that he / she has determined and verified all materials, field measurements, and field construction criteria related thereto, or will do so, and that he / she has checked and coordinated the information contained within such submittals with the requirements of the Work and of the Contract Documents. 4.12.6 The Contractor shall not be relieved of responsibility for any deviation from the requirements of the Contract Documents by the Architect's approval of Shop Drawings, Product Data or Samples under Subparagraph 2.2.7 of these General Conditions unless the Contractor has specifically informed the Architect and the State in writing of such deviation at the time of sub- mission and the Architect and the State has given written approval to the specific deviation. The Contractor shall not be relieved from responsibility for errors or omissions in the Shop Drawings, Product Data or Samples by the Architect's approval thereof. 4.12.7 The Contractor shall direct specific attention, in writing or on resubmitted Shop Drawings, Product Data or Samples, to revisions other than those requested by the Architect on previous submittals. 4.12.8 No portion of the Work requiring submission of a Shop Drawing, Product Data or Sample shall be commenced until the submittal has been approved by the Architect as provided in Subparagraph 2.2.7 of these General Conditions. All such portions of the Work shall be in accordance with approved submittals.

  • MSAA Indicator Technical Specification Document This Agreement shall be interpreted with reference to the MSAA Indicator Technical Specifications document.

  • Multi-year Planning Targets Schedule A may reflect an allocation for the first Funding Year of this Agreement as well as planning targets for up to two additional years, consistent with the term of this Agreement. In such an event, the HSP acknowledges that if it is provided with planning targets, these targets: a. are targets only, b. are provided solely for the purposes of planning, c. are subject to confirmation, and d. may be changed at the discretion of the Funder in consultation with the HSP. The HSP will proactively manage the risks associated with multi-year planning and the potential changes to the planning targets; and the Funder agrees that it will communicate any changes to the planning targets as soon as reasonably possible.

  • Third Party Components The Products and Services may contain third party components (including open source software) subject to separate license agreements. To the limited extent a third party license expressly supersedes this XXXX, such third party license governs Customer’s use of that third party component.

  • Research Project The findings of any research project, which would change the provisions of this Agreement will not be implemented until such changes are negotiated and agreed to by the parties.

  • Research Program The term “Research Program” shall mean the research program to be undertaken by TSRI under the direction and control of the Principal Investigator as expressly set forth on Exhibit A hereto.

  • Manufacturing Technology Transfer Upon AbbVie’s written request with respect to a given Collaboration CAR-T Product and Licensed Product, Caribou shall effect a full transfer to AbbVie or its designee (which designee may be an Affiliate or a Third Party Provider) of all Materials and Know-How Controlled by Caribou relating to the then-current process for the Manufacture of such Collaboration CAR-T Product and any corresponding Licensed Products (each, a “Manufacturing Process”). Caribou shall provide, shall cause its Affiliates to provide, and shall use Commercially Reasonable Efforts to assist AbbVie in causing all Third Party Providers to provide, all reasonable assistance requested by AbbVie to enable AbbVie (or its Affiliate or designated Third Party Provider, as applicable) to implement each Manufacturing Process at the facilities designated by AbbVie. If requested by AbbVie, such assistance shall include facilitating the entering into of agreements with applicable Third Party suppliers relating to such Collaboration CAR-T Product and any corresponding Licensed Products. Without limitation of the foregoing, in connection with the Manufacturing Process and related transfer: (a) Caribou shall, and shall cause its Affiliates to, make available to AbbVie (or its Affiliate or designated Third Party Provider, as applicable), and shall use Commercially Reasonable Efforts to assist AbbVie in causing all Third Party Providers to make available to AbbVie, from time to time as AbbVie may request, all Materials and Manufacturing-related Know-How Controlled by Caribou relating to each Manufacturing Process, including methods, reagents and processes and testing/characterization Know-How, and all documentation constituting material support, performance advice, shop practice, standard operating procedures, specifications as to Materials to be used, and control methods, that are necessary or reasonably useful to enable AbbVie (or its Affiliate or designated Third Party manufacturer, as applicable) to use and practice such Manufacturing Process; (b) Caribou shall cause all appropriate employees and representatives of Caribou and its Affiliates, and shall use Commercially Reasonable Efforts to assist AbbVie in causing all appropriate employees and representatives of Third Party Providers, to meet with employees or representatives of AbbVie (or its Affiliate or designated Third Party Provider, as applicable) at the applicable manufacturing facility at mutually convenient times to assist with the working up and use of each Manufacturing Process and with the training of the personnel of AbbVie (or its Affiliate or designated Third Party Provider, as applicable) to the extent necessary or reasonably useful to enable AbbVie (or its Affiliate or designated Third Party Provider, as applicable) to use and practice such Manufacturing Process; (c) Without limiting the generality of this Section 4.4.2, Caribou shall cause all appropriate analytical and quality control laboratory employees and representatives of Caribou and its Affiliates, and shall use Commercially Reasonable Efforts to assist AbbVie in causing all appropriate analytical and quality control laboratory employees and representatives of Third Party Providers, to meet with employees or representatives of AbbVie (or its Affiliate or designated Third Party Provider, as applicable) at the applicable manufacturing facility and make available all necessary equipment, at mutually convenient times, to support and execute the provision of all applicable analytical methods and the validation thereof (including all applicable Know-How, Information and Materials Controlled by Caribou, and sufficient supplies of all primary and other reference standards); (d) Caribou shall, and shall cause its Affiliates to, take such steps, and shall use Commercially Reasonable Efforts to assist AbbVie in causing Third Party Providers take such steps, as are necessary or reasonably useful to assist AbbVie (or its Affiliate or designated Third Party Provider, as applicable) in obtaining any necessary licenses, permits or approvals from Regulatory Authorities with respect to the Manufacture of the applicable Collaboration CAR-T Products and corresponding Licensed Products at the applicable facilities; and (e) Caribou shall, and shall cause its Affiliates to, provide, and shall use Commercially Reasonable Efforts to assist AbbVie in causing Third Party Providers to provide, such other assistance as AbbVie (or its Affiliate or designated Third Party Provider, as applicable) may reasonably request to enable AbbVie (or its Affiliate or designated Third Party Provider, as applicable) to use and practice each Manufacturing Process and otherwise to Manufacture the applicable Collaboration CAR-T Products and corresponding Licensed Products.

  • Research Plan The Parties recognize that the Research Plan describes the collaborative research and development activities they will undertake and that interim research goals set forth in the Research Plan are good faith guidelines. Should events occur that require modification of these goals, then by mutual agreement the Parties can modify them through an amendment, according to Paragraph 13.6.

  • Development Phase contractual phase initiated with the approval of ANP for the Development Plan and which is extended during the Production Phase while investments in xxxxx, equipment, and facilities for the Production of Oil and Gas according to the Best Practices of the Oil Industry are required.

  • Development Schedule The Project shall substantially comply with the specific timetables and triggers for action set forth in Article 5 of this Agreement. The parties acknowledge that, as provided in G.S. 160A-400.25(b), the failure to meet a commencement or completion date shall not, in and of itself, constitute a material breach of this Agreement pursuant to G.S. 160A-400.27 but must be judged based upon the totality of the circumstances.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!