Employee Categories All employees fall into one or the other of four principal categories as outlined below.
Employment Categories (a) Employees under this Agreement will be employed in one of the following categories: (i) full-time; (ii) part time; or (iii) casual. (b) At the time of engagement an employer will inform each employee whether they are employed on a full-time, part time or casual basis. An employer may direct an employee to carry out such duties that are within the limits of the employee’s skill, competence and training, consistent with the respective classification.
Criminal History Category With regard to determining defendant’s criminal history points and criminal history category, based on the facts now known to the government, defendant’s criminal history points equal zero and defendant’s criminal history category is I.
Categories All personnel of the Logistics & Supply Business Unit, within the following work categories and in classifications as enumerated in Article 8.03, are covered by this Agreement. Nothing in this agreement prevents an employee from performing either on a day to day or regular basis, any function or task that is generally performed by any category, provided that the employee is competent to perform the work required. Any efficiencies attained out of this flexibility is not intended to eliminate a category.
Client Categorisation 4.1. The client understands and accepts that each category of Clients has its individual level of regulative protection acknowledging that Retail Clients have the highest level of protection whereas Professional Clients and Eligible Counterparties are considered to be more experienced, informed, skilled and able to estimate their risk, therefore are provided with a lower level of protection. 4.2. The Company will treat the Client as a Retail Client, Professional Client or Eligible Counterparty, depending on how the Client completes the Application Form and according to the method of categorisation as this method is explained under the title “Client Categorisation” (Appendix II), and by accepting this Agreement the Client accepts application of such method. 4.3. The Client accepts that when categorising the Client and dealing with him, the Company will rely on the accuracy, completeness and correctness of the information provided by the Client in his Application Form and the Client has the responsibility to immediately notify the Company in writing if such information changes. 4.4. The Company has the right to review the Client’s Categorisation and change his Categorisation if this is deemed necessary (subject to Applicable Laws).
Power Factor Design Criteria Developer shall design the Large Generating Facility to maintain an effective power delivery at demonstrated maximum net capability at the Point of Interconnection at a power factor within the range established by the Connecting Transmission Owner on a comparable basis, until NYISO has established different requirements that apply to all generators in the New York Control Area on a comparable basis. The Developer shall design and maintain the plant auxiliary systems to operate safely throughout the entire real and reactive power design range. The Connecting Transmission Owner shall not unreasonably restrict or condition the reactive power production or absorption of the Large Generating Facility in accordance with Good Utility Practice.
Unbundled Channelization (Multiplexing) 5.7.1 To the extent NewPhone is purchasing DS1 or DS3 or STS-1 Dedicated Transport pursuant to this Agreement, Unbundled Channelization (UC) provides the optional multiplexing capability that will allow a DS1 (1.544 Mbps) or DS3 (44.736 Mbps) or STS-1 (51.84 Mbps) Network Elements to be multiplexed or channelized at a BellSouth central office. Channelization can be accomplished through the use of a multiplexer or a digital cross-connect system at the discretion of BellSouth. Once UC has been installed, NewPhone may request channel activation on a channelized facility and BellSouth shall connect the requested facilities via COCIs. The COCI must be compatible with the lower capacity facility and ordered with the lower capacity facility. This service is available as defined in NECA 4. 5.7.2 BellSouth shall make available the following channelization systems and interfaces: 5.7.2.1 DS1 Channelization System: channelizes a DS1 signal into a maximum of twenty- four (24)
Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.
Check Meters Developer, at its option and expense, may install and operate, on its premises and on its side of the Point of Interconnection, one or more check meters to check Connecting Transmission Owner’s meters. Such check meters shall be for check purposes only and shall not be used for the measurement of power flows for purposes of this Agreement, except as provided in Article 7.4 below. The check meters shall be subject at all reasonable times to inspection and examination by Connecting Transmission Owner or its designee. The installation, operation and maintenance thereof shall be performed entirely by Developer in accordance with Good Utility Practice.
Loop Provisioning Involving Integrated Digital Loop Carriers 2.6.1 Where Freedom has requested an Unbundled Loop and BellSouth uses IDLC systems to provide the local service to the End User and BellSouth has a suitable alternate facility available, BellSouth will make such alternative facilities available to Freedom. If a suitable alternative facility is not available, then to the extent it is technically feasible, BellSouth will implement one of the following alternative arrangements for Freedom (e.g. hairpinning): 1. Roll the circuit(s) from the IDLC to any spare copper that exists to the customer premises. 2. Roll the circuit(s) from the IDLC to an existing DLC that is not integrated. 3. If capacity exists, provide "side-door" porting through the switch. 4. If capacity exists, provide "Digital Access Cross Connect System (DACS)- door" porting (if the IDLC routes through a DACS prior to integration into the switch). 2.6.2 Arrangements 3 and 4 above require the use of a designed circuit. Therefore, non- designed Loops such as the SL1 voice grade and UCL-ND may not be ordered in these cases. 2.6.3 If no alternate facility is available, and upon request from Freedom, and if agreed to by both Parties, BellSouth may utilize its Special Construction (SC) process to determine the additional costs required to provision facilities. Freedom will then have the option of paying the one-time SC rates to place the Loop.
