Manufacturer's Recommendations All work or materials shall be installed in accordance with the manufacturer's recommendations and requirements. The Contractor shall obtain the manufacturer’s recommendations and requirements, for its use at the Site in executing the Work, copies of bulletins, circulars, catalogues, or other publications bearing the manufacturer’s titles, numbers, editions, dates, etc. If the manufacturer’s recommendations and requirements are not available, the Contractor shall request installation instructions from the Design Professional.
Ongoing Review and Revisions As set forth in Section 35.7, the Parties have agreed to the coordination and exchange of data and information under this Agreement to enhance system reliability and efficient market operations as systems exist and are contemplated as of the Effective Date. The Parties expect that these systems and the technology applicable to these systems and to the collection and exchange of data will change from time to time throughout the term of this Agreement. The Parties agree that the objectives of this Agreement can be fulfilled efficiently and economically only if the Parties, from time to time, review and, as appropriate, revise the requirements stated herein in response to such changes, including deleting, adding, or revising requirements and protocols. Each Party will negotiate in good faith in response to such revisions the other Party may propose from time to time. Nothing in this Agreement, however, shall require any Party to reach agreement with respect to any such changes, or to purchase, install, or otherwise implement new equipment, software, or devices, or functions, except as required to perform this Agreement.
Personnel File Review a. A unit member has the right upon his/her own request to review the contents of his/her personnel file. The review will be conducted in the presence of the administrator, or his/her designee, responsible for the safekeeping of such file. The employee may have a committee person assist in said review. Such review shall be conducted at a mutually agreeable time. A copy of requested material will be provided.
Technical Objections to Grievances It is the intent of both Parties of this Agreement that no grievance shall be defeated merely because of a technical error, other than time limitations in processing the grievance through the grievance procedure. To this end, an arbitration board shall have the power to allow all necessary amendments to the grievance and the power to waive formal procedural irregularities in the processing of a grievance, in order to determine the real matter in dispute and to render a decision according to equitable principles and the justice of the case.
Technical Specifications The Technical Specifications furnished on the CD are intended to establish the standards for quality, performance and technical requirements for all labor, workmanship, material, methods and equipment necessary to complete the Work. When specifications and drawings are provided or referenced by the County, these are to be considered part of the Scope of Work, and to be specifically documented in the Detailed Scope of Work. For convenience, the County supplied specifications, if any, and the Technical Specifications furnished on the CD.
Technical Proposal The technical proposal may be presented in free format. It shall not exceed ten pages, not counting the CVs. It shall respect the following page limit and structure: • Technical methodology (max. 7 pages) • Quality management (max. 1 page) • Project management (max. 1 page) • Resource management (proposal (max. 1 page) + CVs of experts)
Technical Objections to Grievance No grievance will be defeated or denied by any minor technical objection.
Technical Proposals Technical proposal information will be streamlined, e.g., the Government anticipates written proposals consisting of thirty (30) pages or less stating compliance or exception to requirements, risks, assumptions and conflict of interest issues. Proposals shall not merely restate PWS/SOO requirements. Written technical proposals shall normally address: * Technical Approach and descriptive narrative of the contractor's understanding of the requested effort * PWS in response to a SOO * Integrated Master Plan (if applicable) * Integrated Master Schedule (if applicable) * Key Personnel Assigned * Quantities/Hours of Personnel by Labor Categories and narrative justification (if applicable) * Other Direct Costs (ODCs) (materials and supplies, travel, training, etc.(quantities and types only)) * Period of Performance * Government-Furnished Equipment (GFE)/Government-Furnished Information (GFI) * Security (including clearance level) * Teaming Arrangement (including subcontracting; identify new ACAs) * Small Business Plan (if a large business) * Other Pertinent Data, such as assumptions made.
Implementation Specifications 1. The accounting shall contain the date, nature, and purpose of such disclosures, and the name and address of the person or agency to whom the disclosure is made.
