Vertical Accuracy Requirements for Conventional Surveys Sample Clauses

Vertical Accuracy Requirements for Conventional Surveys. Vertical control shall be established (at a minimum) on the North American Vertical Datum of 1988 (NAVD 1988). 1st ORDER 2nd ORDER 3rd ORDER REMARKS AND FORMULAE Error of Closure 0.013 feet √K 0.026 feet √K 0.039 feet √K Loop or between control monuments Maximum Length of Sight 250 feet 300 feet With good atmospheric conditions Difference in Foresight and Backsight Distances ±10 feet ±20 feet ±30 feet Per instrument set up Total Difference in Foresight and Backsight Distances ±20 feet. per second ±50 feet per second ±70 feet per second Per total section or loop Recommended Length of Section or Loop 2.0 miles 3.0 miles 4.0 miles Maximum distance before closing or in loop Maximum Recommended Distance Between Benchmarks 2000 feet 2500 feet 3000 feet Permanent or temporary benchmarks set or observed along the route Level Rod Reading ± 0.001 foot ± 0.001 foot ± 0.001 foot Recommended Instruments and Leveling Rods Automatic or tilting w/ parallel plate micrometer precise rods Automatic or tilting w/ optical micrometer precise rods Automatic or quality spirit standard, quality rod When two or more level rods are used, they should be identically matched Principal Uses Broad area control, subsidence or motion studies jig & tool settings Broad area control, engineering projects basis for subsequent level work Small area control, drainage studies, some construction and engineering
AutoNDA by SimpleDocs

Related to Vertical Accuracy Requirements for Conventional Surveys

  • Insurance Requirements Vendor agrees to maintain the following minimum insurance requirements for the duration of this Agreement. All policies held by Vendor to adhere to this term shall be written by a carrier with a financial size category of VII and at least a rating of “A‐” by A.M. Best Key Rating Guide. The coverages and limits are to be considered minimum requirements and in no way limit the liability of the Vendor(s). Any immunity available to TIPS or TIPS Members shall not be used as a defense by the contractor's insurance policy. Only deductibles applicable to property damage are acceptable, unless proof of retention funds to cover said deductibles is provided. "Claims made" policies will not be accepted. Vendor’s required minimum coverage shall not be suspended, voided, cancelled, non‐renewed or reduced in coverage or in limits unless replaced by a policy that provides the minimum required coverage except after thirty (30) days prior written notice by certified mail, return receipt requested has been given to TIPS or the TIPS Member if a project or pending delivery of an order is ongoing. Upon request, certified copies of all insurance policies shall be furnished to the TIPS or the TIPS Member. Vendor agrees that when Vendor or its subcontractors are liable for any damages or claims, Vendor’s policy, shall be primary over any other valid and collectible insurance carried by the Member or TIPS. General Liability: $1,000,000 each Occurrence/Aggregate Automobile Liability: $300,000 Includes owned, hired & non‐owned Workers' Compensation: Statutory limits for the jurisdiction in which the Vendor performs under this Agreement. If Vendor performs in multiple jurisdictions, Vendor shall maintain the statutory limits for the jurisdiction with the greatest dollar policy limit requirement. Umbrella Liability: $1,000,000 each Occurrence/Aggregate

  • Compliance with Laws Comply in all material respects with the requirements of all Laws and all orders, writs, injunctions and decrees applicable to it or to its business or property, except in such instances in which (a) such requirement of Law or order, writ, injunction or decree is being contested in good faith by appropriate proceedings diligently conducted; or (b) the failure to comply therewith could not reasonably be expected to have a Material Adverse Effect.

  • Compliance Neither the Company nor any Subsidiary: (i) is in default under or in violation of (and no event has occurred that has not been waived that, with notice or lapse of time or both, would result in a default by the Company or any Subsidiary under), nor has the Company or any Subsidiary received notice of a claim that it is in default under or that it is in violation of, any indenture, loan or credit agreement or any other agreement or instrument to which it is a party or by which it or any of its properties is bound (whether or not such default or violation has been waived), (ii) is in violation of any judgment, decree or order of any court, arbitrator or other governmental authority or (iii) is or has been in violation of any statute, rule, ordinance or regulation of any governmental authority, including without limitation all foreign, federal, state and local laws relating to taxes, environmental protection, occupational health and safety, product quality and safety and employment and labor matters, except in each case as could not have or reasonably be expected to result in a Material Adverse Effect.

  • Safety Where an employee is prevented from working at the employee’s particular function as a result of unsafe conditions caused by the inclement weather, the employee may be transferred to other work in the employee’s classification on site, until the unsafe conditions are rectified. Where such alternative is not available and until the unsafe conditions are rectified, the employee shall remain on site. The employee shall be paid for such time without reduction of the employees’ inclement weather entitlement.

  • Dimensions Education Bachelor’s or Master’s Degree in Computer Science, Information Systems, or other related field. Or equivalent work experience. Experience: A minimum of 7 years of experience with large and complex database management systems.

  • Scope of Services The specific scope of work for each job shall be determined in advance and in writing between TIPS Member, Member’s design professionals and Vendor. It is permitted for the TIPS Member to provide a general scope description, but the awarded vendor should provide a written scope of work, and if applicable, according to the TIPS Member’s design Professional as part of the proposal. Once the scope of the job is agreed to, the TIPS Member will issue a PO and/or an Agreement or Contract with the Job Order Contract Proposal referenced or as an attachment along with bond and any other special provisions agreed by the TIPS Member. If special terms and conditions other than those covered within this solicitation and awarded Agreements are required, they will be attached to the PO and/or an Agreement or Contract and shall take precedence over those in this base TIPS Vendor Agreement.

  • Deliverables Upon satisfactory completion of the work authorization, the Engineer shall submit the deliverables as specified in the executed work authorization to the State for review and acceptance.

  • Limitation of Liability No provision hereof, in the absence of any affirmative action by the Holder to exercise this Warrant to purchase Warrant Shares, and no enumeration herein of the rights or privileges of the Holder, shall give rise to any liability of the Holder for the purchase price of any Common Stock or as a stockholder of the Company, whether such liability is asserted by the Company or by creditors of the Company.

  • Representations and Warranties Borrower represents and warrants as follows:

  • Grievance Procedure 7.01 For purposes of this Agreement, a grievance is defined as a difference arising between the parties relating to the interpretation, application, administration or alleged violation of the Agreement including any question as to whether a matter is arbitrable.

Time is Money Join Law Insider Premium to draft better contracts faster.