Workflows for Provisioning and Management of Intra Sample Clauses

Workflows for Provisioning and Management of Intra. DC Optical Connectivity The on-demand provisioning of intra-DC connections can be requested by the cloud orchestrator to dynamically create optical path between the nodes of the Data Centre dedicated to management traffic. Combining Optics and SDN In next Generation Data Centre Networks Figure 19 – Provisioning of intra-DC optical connectivity Figure 19 shows the workflow to create an optical path over the DCN. The request is processed by the Optical Provisioning Manager component (step 1), which uses the operator’s policies (step 2) to define the path characteristics in terms of constraints, metrics, optimization functions etc. (step 3). The elaboration of the optical path is performed through the algorithms of the Path Computation component (step 4 and 6), which runs over a network graph derived from the DCN topology view maintained by the Topology Manager (step 5). The Optical Provisioning Manager is responsible to coordinate the configuration of the DCN resources along the whole path, following the centralized concept of the SDN controller. Therefore, for each hop specified in the returned path, it creates a cross-connection on the associated physical node making use of the methods exposed by the SDN driver (step 7), which in turn configure the data plane (steps 8 and 9). When the whole path is established, the Optical Provisioning Manager registers itself with the Monitoring service, in order to be notified in case of failures at the devices along the route (step 10).
Sample 1
AutoNDA by SimpleDocs

Related to Workflows for Provisioning and Management of Intra

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CBB chooses to subtend a Verizon access Tandem, CBB’s NPA/NXX must be assigned by CBB to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG.

  • Ordering and Provisioning 53.1 National Exchange Access Center (NEAC)

  • Configuration Management The Contractor shall maintain a configuration management program, which shall provide for the administrative and functional systems necessary for configuration identification, control, status accounting and reporting, to ensure configuration identity with the UCEU and associated cables produced by the Contractor. The Contractor shall maintain a Contractor approved Configuration Management Plan that complies with ANSI/EIA-649 2011. Notwithstanding ANSI/EIA-649 2011, the Contractor’s configuration management program shall comply with the VLS Configuration Management Plans, TL130-AD-PLN-010-VLS, and shall comply with the following:

  • Monitoring and Management Information C10.1 The Contractor shall comply with the monitoring arrangements set out in the Monitoring Schedule including, but not limited to, providing such data and information as the Contractor may be required to produce under the Contract.

  • Joint Network Implementation and Grooming Process Upon request of either Party, the Parties shall jointly develop an implementation and grooming process (the “Joint Grooming Process” or “Joint Process”) which may define and detail, inter alia:

  • Implementation and Management 1.1 Properly constituted Occupational Health and Safety (OH&S) Committees or, where there is no OH&S Committee, Site Safety Supervisors/Safety Officers in conjunction with worker representatives, are the appropriate bodies to implement and administer alcohol and drug policy/programs (* see below).

  • Procedures for Providing NP Through Full NXX Code Migration Where a Party has activated an entire NXX for a single Customer, or activated at least eighty percent (80%) of an NXX for a single Customer, with the remaining numbers in that NXX either reserved for future use by that Customer or otherwise unused, if such Customer chooses to receive Telephone Exchange Service from the other Party, the first Party shall cooperate with the second Party to have the entire NXX reassigned in the LERG (and associated industry databases, routing tables, etc.) to an End Office operated by the second Party. Such transfer will be accomplished with appropriate coordination between the Parties and subject to appropriate industry lead times for movements of NXXs from one switch to another. Neither Party shall charge the other in connection with this coordinated transfer.

  • Local Control Center, Metering and Telemetry The NTO shall operate, pursuant to ISO Tariffs, ISO Procedures, Reliability Rules and all other applicable reliability rules, standards and criteria on a twenty-four (24) hour basis, a suitable local control center(s) with all equipment and facilities reasonably required for the ISO to exercise ISO Operational Control over NTO Transmission Facilities Under ISO Operational Control, and for the NTO to fulfill its responsibilities under this Agreement. Operation of the NYS Power System is a cooperative effort coordinated by the ISO control center in conjunction with local control centers and will require the exchange of all reasonably necessary information. The NTO shall provide the ISO with Supervisory Control and Data Acquisition (“SCADA”) information on facilities listed in Appendices A-1 and A-2 herein as well as on generation and merchant transmission resources interconnected to the NTO’s transmission facilities pursuant to the ISO OATT. The NTO shall provide metering data for its transmission facilities to the ISO, unless other parties are authorized by the appropriate regulatory authority to provide metering data. The NTO shall collect and submit to the ISO billing quality metering data and any other information for its transmission facilities required by the ISO for billing purposes. The NTO shall provide to the ISO the telemetry and other operating data from generation and merchant transmission resources interconnected to its transmission facilities that the ISO requires for the operation of the NYS Power System. The NTO will establish and maintain a strict code of conduct to prevent such information from reaching any unauthorized person or entity.

  • Network Maintenance and Management 36.1 The Parties will work cooperatively to implement this Agreement. The Parties will exchange appropriate information (for example, maintenance contact numbers, network information, information required to comply with law enforcement and other security agencies of the Government, escalation processes, etc.) to achieve this desired result.

  • Quality Management System Supplier hereby undertakes, warrants and confirms, and will ensue same for its subcontractors, to remain certified in accordance with ISO 9001 standard or equivalent. At any time during the term of this Agreement, the Supplier shall, if so instructed by ISR, provide evidence of such certifications. In any event, Supplier must notify ISR, in writing, in the event said certification is suspended and/or canceled and/or not continued.

Time is Money Join Law Insider Premium to draft better contracts faster.