Leak Point definition

Leak Point means the pressure at which a PRD first opens to release vapors.
Sample 1Sample 2
Leak Point means the lowest pressure at which emissions are released from any pressure relief devices on a Tank System, as determined consistent with the Closed Loop Design Guideline. For purposes of establishing the Leak Point for a Closed Loop Vapor Control System, the value of the Leak Point will not be a value exceeding the Set Point.
Sample 1Sample 2
Leak Point means the pressure at which a PRD first opens to release vapors, as determined in accordance with Paragraph 35.
Sample 1Sample 2

Examples of Leak Point in a sentence

  • The purpose of the Closed Loop Design Guideline is to prescribe the steps taken to design, install and operate the Closed Loop Vapor Control Systems by reading tank pressures and controlling liquid flow and vapor flow to the tanks, thereby ensuring tank pressure does not exceed the Leak Point.

  • The purpose of the Closed Loop Design Guideline is to prescribe the steps taken to design, install and optimize Closed Loop Vapor Control Systems by reading tank pressures and controlling liquid flow and vapor flow to the tanks, thereby controlling the Potential Peak Instantaneous Vapor Flow Rate, PPIVFR duration, or PPIVFR frequency, to ensure tank pressure does not exceed the Leak Point.

  • For Closed Loop Vapor Control Systems, [COMPANY] shall demonstrate that the Closed Loop Vapor Control System actively controls tank pressures based on all control points and an IR Camera verification of the Leak Point in a manner consistent with the Closed Loop Design Guideline.

  • A Closed Loop Control System automatically regulates hydrocarbon flow to the Tank System, thereby controlling the vapor flow rate, duration, and frequency to maintain Vapor Control System pressure below the Leak Point of the Vapor Control System pressure relief device(s).

  • Ensure Tank System pressures do not exceed the Leak Point in accordance with a revised Closed Loop Design Guideline.

  • At baseline, the patients were assessed by anamnesis, physical examination, pad usage, urodynamic study (Valsalva Leak Point Pressure – VLPP ) standardized one-hour pad weight test (PWT), Stamey grading of incontinence and “KING´S HEALTH QUESTIONNAIRE” (KHQ)1.

  • If a Closed Loop Control System is selected, the Leak Point shall be determined by measuring the Vapor Control System pressure at a specific location during pressurization of the Vapor Control System, noting the lowest pressure at which VOC emissions are detected from any Vapor Control System pressure relief device using an IR camera.

  • Figure 2: Velocity Field around the Leak Point at inlet Velocity 0.1ms−1, 1ms−1 ,5ms−1 and 5ms−1 respectivelyThe effect of inlet velocity on the flow rate at the leak point can be seen on a graph in Figure 3, of leakage flow rate plotted against the inlet velocity.

  • Aims of study.Since its introduction into the urodynamic armamentarium, Abdominal Leak Point Pressure (ALPP) has been used with ever more increasing frequency for the urodynamic evaluation of urinary stress incontinence (USI), for the diagnosis of intrinsic sphincteric deficiency (ISD).

  • The green box in the center of the Leak Point, or at the end of the Pipeline segment, will turn red when the connection has been properly made.


More Definitions of Leak Point

Leak Point means: (i) the lowest pressure at which emissions are released from any pressure relief devices on a Tank System, as determined consistent with the Closed Loop Design Guideline. For purposes of establishing the Leak Point for a Closed Loop Vapor Control System, the value of the Leak Point shall not be a value exceeding the Set Point; and (ii) for an Open Loop Vapor Control System, the Leak Point developed pursuant to Paragraph 48 (Pressure Monitor Trigger Point and Leak Point Development).
Sample 1Sample 2
Leak Point means the lowest pressure at which emissions are released from any pressure relief devices, including thief hatches, on a Vapor Control System. The Leak Point may be determined by measurement of the Vapor Control System pressure during pressurization of the Vapor Control System, noting the lowest pressure at which emissions are observed from any Vapor Control System pressure relief device during the field survey. For purposes of establishing the Leak Point for a Closed Loop Control System, the value of the Leak Point must not exceed the lowest rated pressure at which any Vapor Control System pressure relief device is designed to open or relieve pressure.
Sample 1

Related to Leak Point

  • Flash point means the lowest temperature of a liquid at which its vapours form a flammable mixture with air;

  • H-point means the pivot centre of the torso and thigh of the H-point machine when installed in a vehicle seat in accordance with Annex 3. Once determined in accordance with the procedure described in Annex 3, the "H" point is considered fixed in relation to the seat-cushion structure and is considered to move with it when the seat is adjusted in the X direction.

  • Meet Point A point, designated by the Parties, at which one Party’s responsibility for service begins and the other Party’s responsibility ends.

  • Plasma arc incinerator means any enclosed device using a high intensity electrical discharge or arc as a source of heat followed by an afterburner using controlled flame combustion and which is not listed as an industrial furnace.

  • Diatomaceous earth filtration means a process resulting in substantial particulate removal in which (1) a precoat cake of diatomaceous earth filter media is deposited on a support membrane (septum), and (2) while the water is filtered by passing through the cake on the septum, additional filter media known as body feed is continuously added to the feed water to maintain the permeability of the filter cake.

  • chemical tanker means a ship constructed or adapted and used for the carriage in bulk of any liquid product listed in chapter 17 of the International Bulk Chemical Code;

  • High global warming potential hydrofluorocarbons means any hydrofluorocarbons in a particular end use for which EPA’s Significant New Alternatives Policy (SNAP) program has identified other acceptable alternatives that have lower global warming potential. The SNAP list of alternatives is found at 40 CFR Part 82 subpart G with supplemental tables of alternatives available at (http://www.epa.gov/snap/).

  • Engine degreaser means a cleaning product designed to remove grease, grime, oil and other contaminants from the external surfaces of engines and other mechanical parts.

  • Reid vapor pressure means the vapor pressure of crude oil or other volatile petroleum products at 100 degrees Fahrenheit as determined by the latest edition of ASTM D6377 (RVPE): Standard Test Method for Determination of Vapor Pressure of Crude Oil.

  • Tank means an enclosed space which is formed by the permanent structure of a ship and which is designed for the carriage of liquid in bulk.

  • Infiltration means water other than wastewater that enters a sewer system (including sewer system and foundation drains) from the ground through such means as defective pipes, pipe joints, connections, or manholes. Infiltration does not include, and is distinguished from, inflow.

  • Combined sewer overflow means the discharge of untreated or

  • Psig means pounds per square inch gauge.

  • CO2 means carbon dioxide.

  • Measurement Point means the emission source for which continuous emission measurement systems (CEMS) are used for emission measurement, or the cross-section of a pipeline system for which the CO2 flow is determined using continuous measurement systems;

  • Demarcation Point means the point where Qwest owned or controlled facilities cease, and CLEC, End User Customer, premises owner or landlord ownership or control of facilities begin. "Designed, Verified and Assigned Date" or "DVA" means the date on which implementation groups are to report that all documents and materials have been received and are complete.

  • Injection well means a well into which fluids are injected. (See also “underground injection”.)

  • Leak of UPSI means communication of information which is/deemed to be UPSI by any person, who is in possession of UPSI, to any other person, directly or indirectly, overtly or covertly or in any manner whatsoever, except for legitimate purposes, performance of duties or discharge of legal obligations.

  • Injection means the injection of carbon dioxide streams into the storage site;

  • Seepage pit means an excavation deeper than it is wide that receives septic tank effluent and from which the effluent seeps from a structural internal void into the surrounding soil through the bottom and openings in the side of the pit.

  • Hydrozone means a portion of the landscaped area having plants with similar water needs and rooting depth. A hydrozone may be irrigated or non-irrigated.

  • Exfiltration means any unauthorized release of data from within an information system. This includes copying the data through covert network channels or the copying of data to unauthorized media.

  • Harvest batch means a specifically identified quantity of dried flower or trim, leaves, and other cannabis plant matter that is uniform in strain, harvested at the same time, and, if applicable, cultivated using the same pesticides and other agricultural chemicals, and harvested at the same time.

  • Slug loading means any pollutant, including oxygen demanding pollutants, released in a discharge at a flow rate and/or pollutant concentration as to cause interference in the POTW.

  • Origin Point means the receipt/inception point(s) where Product is received into the System, as such points are specified in Section III of this tariff.

  • Vapor tight means equipment that allows no loss of vapors. Compliance with vapor-tight requirements can be determined by checking to ensure that the concentration at a potential leak source is not equal to or greater than 100 percent of the lower explosive limit (LEL) when measured with a combustible gas detector, calibrated with propane, at a distance of 1 inch (2.54 cm) from the source.