AIM OF THE QAA Sample Clauses

AIM OF THE QAA. (IATF 16949: Preface Objective) As a supplier to the automotive industry, the Xxxx Group manufactures high-quality products. The QAA is intended to ensure the procurement and manufacture of flawless products through appropriate measures. In addition, individual quality assurance agreements can be made between the business partners, the plants and the supplier or sub-supplier. By describing the minimum requirements for the SUPPLIER's quality management system, the QAA is intended to help avoid quality problems, ensure smooth processes and high-quality, defect-free products between the Xxxx Group and the SUPPLIER, and minimise costs. In the event of problems, this has a significant influence on the internal procedures and processes at the Xxxx Group and must be avoided in order not to jeopardise the quality of the end products. The QAA describes the framework conditions and processes, both technical and organisational, that are required to achieve the desired quality objectives. The aim is for the SUPPLIER to strive for continuous improvement "KAIZEN" and pursue the goal of "zero defect strategy". The SUPPLIER shall ensure strict compliance with this agreement. Product liability and warranty obligations must also be observed and complied with.
Sample 1
AutoNDA by SimpleDocs

Related to AIM OF THE QAA

  • Teaching Staff Assigned to More Than One Building Each Educator who is assigned to more than one building will be evaluated by the appropriate administrator where the individual is assigned most of the time. The principal of each building in which the Educator serves must review and sign the evaluation, and may add written comments. In cases where there is no predominate assignment, the superintendent will determine who the primary evaluator will be.

  • Provisioning of High Frequency Spectrum and Splitter Space 3.2.1 BellSouth will provide <<customer_name>> with access to the High Frequency Spectrum as follows:

  • ROAD WORK PHASE APPROVAL Purchaser shall obtain written approval from the Contract Administrator upon completion of each of the following phases of road work:  Drainage installation  Subgrade compaction  Rock compaction SUBSECTION RESTRICTIONS

  • Construction Progress Meetings The Design Professional shall attend Construction Progress Meetings periodically held by the Contractor at the Site on a schedule determined by the Contractor. The Design Professional shall review the minutes of the meeting and provide his written comments to the minutes to the Owner and Contractor within seven calendar days after receipt of the meeting minutes.

  • Commerce eXtensible Markup Language (cXML) This standard establishes the data contents required for invoicing via cXML within the context of an electronic environment. This transaction set can be used for invoicing via the AN for catalog and non-catalog goods and services. The cXML format is the Ariba preferred method for electronic invoicing.

  • Preparatory Contract Negotiations Meetings Where operational requirements permit, the Employer will grant leave without pay to an employee to attend preparatory contract negotiations meetings.

  • PROGRESS OF THE WORK Notwithstanding any other provision of the Contract Documents, if Contractor fails or refuses, for any reason and at any time, to furnish adequate materials, labor, equipment, tools and/or services to maintain the progress of the Work, District may, in its sole discretion, after seventy-two (72) hours’ advance written notice of same from District to Contractor, direct, instruct, and authorize a separate contractor selected by District to furnish such materials, labor, equipment, tools and/or services necessary to maintain progress of the Work. District may in its discretion deduct the amount of any and all costs, expenses, and/or other charges incurred thereby from the Contract Price then or thereafter due Contractor.

  • Placement of EPP probes Probes for measuring EPP parameters shall be placed inside or close to Registrars points of access to the Internet across the different geographic regions; care shall be taken not to deploy probes behind high propagation-­‐delay links, such as satellite links.

  • Signaling Parameters All SS7 signaling parameters will be provided in conjunction with traffic exchange trunk groups, where and as available. These parameters include Automatic Number Identification ("ANI"), Calling Party Number ("CPN"), Privacy Indicator, calling party category information, originating line information, charge number, etc. Also included are all parameters relating to network signaling information, such as Carrier Information Parameter ("CIP"), wherever such information is needed for call routing or billing. GTE will provide SS7 via GR-394-SS7 and/or GR-317-SS7 format(s).

  • Public Posting of Approved Users’ Research Use Statement The PI agrees that information about themselves and the approved research use will be posted publicly on the dbGaP website. The information includes the PI’s name and Requester, project name, Research Use Statement, and a Non-Technical Summary of the Research Use Statement. In addition, and if applicable, this information may include the Cloud Computing Use Statement and name of the CSP or PCS. Citations of publications resulting from the use of controlled-access datasets obtained through this DAR may also be posted on the dbGaP website.

Time is Money Join Law Insider Premium to draft better contracts faster.