Calibration of Propagation Model Sample Clauses

Calibration of Propagation Model. Propagation models are by nature generally predictive devices. In an effort to tailor the TAP model to Virginia’s terrain, and to take into consideration the variations in antenna patterns resulting from tower size, shadowing, etc., we will take various measurements from several VSP sites. Since the existing VSPHQ tower site in Richmond (the Test Bed Site) is reasonably representative of Virginia terrain; we will base our Virginia terrain calibration on that site and incorporate the information into the TAP program. We will take measurements in the vicinity of a maximum of five VSP sites (including the VSPHQ tower site), for the purpose of modeling the antenna pattern(s) at that site. The sites will be selected to demonstrate tower size variation, shadowing from other devices on the tower, etc. We envision that these measurements will occur over the period of two consecutive weeks. For each VSP site measured, we will run propagation analyses using a Xxxxxxx-Xxxx based analysis tool. We will characterize the area surrounding the site by tile, establishing characteristics such as vegetation, terrain variance, etc. We will then measure the signal levels provided by the analog VHF test bed equipment, and compare these signal levels with those predicted by the model. By identifying variations between the measured and predicted performance (both variations in central tendency and in variances), and correlating these variations with the tile characteristics, we can establish a calibration matrix of dB factors applicable to the test bed site. We can then apply these dB factors to other sites using the same model, for the characteristics identified. We note that transference of these dB factors from the measurement site to another site is not a precise process, and therefore there will be a statistical adjustment that will need to be included in the predictions to accommodate the differences between sites.‌‌‌ The specific process we intend to use in the calibration effort will include the following: • The State and HSMM will agree on appropriate existing VSP sites. • The State will install State supplied VHF conventional system equipment and an antenna system at the site, or we will use the existing equipment. • We will test each site for the parameters required. • The test data will be used to calibrate the computerized propagation analysis model described in Task G1.03.
Sample 1
AutoNDA by SimpleDocs

Related to Calibration of Propagation Model

  • Interoperability To the extent required by applicable law, Cisco shall provide You with the interface information needed to achieve interoperability between the Software and another independently created program. Cisco will provide this interface information at Your written request after you pay Cisco’s licensing fees (if any). You will keep this information in strict confidence and strictly follow any applicable terms and conditions upon which Cisco makes such information available.

  • Testing Procedures Testing will be conducted by an outside certified Agency in such a way to ensure maximum accuracy and reliability by using the techniques, chain of custody procedures, equipment and laboratory facilities which have been approved by the U.S. Department of Health and Human Services. All employees notified of a positive controlled substance or alcohol test result may request an independent test of their split sample at the employee’s expense. If the test result is negative the Employer will reimburse the employee for the cost of the split sample test.

  • System Upgrade Facilities and System Deliverability Upgrades Connecting Transmission Owner shall design, procure, construct, install, and own the System Upgrade Facilities and System Deliverability Upgrades described in Appendix A hereto. The responsibility of the Developer for costs related to System Upgrade Facilities and System Deliverability Upgrades shall be determined in accordance with the provisions of Attachment S to the NYISO OATT.

  • Testing Procedure Limitations The Asset Representations Reviewer will only be required to perform the testing procedures listed under “Tests” in Schedule A, and will have no obligation to perform additional procedures on any Subject Lease or to provide any information other than a Review Report indicating for each Subject Lease whether there was a Test Pass or a Test Fail for each Test, or whether the Subject Lease was a Test Complete and the related reason. However, the Asset Representations Reviewer may provide additional information about any Subject Lease that it determines in good faith to be material to the Review.

  • Standard Operating Procedures Standard Operating Procedures shall not contravene the Canada Labour Code, the Canadian Human Rights Code, or the Collective Agreement, and an allegation of such contravention is subject to the grievance procedure.

  • Equipment Specifications All equipment must meet the contract specifications and all federal and State safety codes and regulations in effect at the date of manufacture. All equipment must be Original Equipment Manufacturer (OEM) equipment unless otherwise stated in the contract. All products, materials, supplies, replacement parts, and equipment offered and furnished must be new, of current manufacturer production, and must have been formally announced by the manufacturer as being commercially available, unless otherwise stated in this Contract.

  • Registry Interoperability and Continuity Registry Operator shall comply with the Registry Interoperability and Continuity Specifications as set forth in Specification 6 attached hereto (“Specification 6”).

  • Technical Specifications The Technical Specifications furnished on the CD are intended to establish the standards for quality, performance and technical requirements for all labor, workmanship, material, methods and equipment necessary to complete the Work. When specifications and drawings are provided or referenced by the County, these are to be considered part of the Scope of Work, and to be specifically documented in the Detailed Scope of Work. For convenience, the County supplied specifications, if any, and the Technical Specifications furnished on the CD.

  • Monthly MWBE Contractor Compliance Report A. In accordance with 5 NYCRR § 142.10, Contractor is required to report Monthly MWBE Contractor Compliance to OGS during the term of the Contract for the preceding month’s activity, documenting progress made towards achievement of the Contract MWBE goals. OGS requests that all Contractors use the New York State Contract System (“NYSCS”) to report subcontractor and supplier payments made by Contractor to MWBEs performing work under the Contract. The NYSCS may be accessed at xxxxx://xx.xxxxxxxxxxxxxx.xxx/. This is a New York State- based system that all State agencies and authorities will be implementing to ensure uniform contract compliance reporting throughout New York State. B. When a Contractor receives a payment from a State agency, it is the Contractor’s responsibility to pay its subcontractors and suppliers in a timely manner. On or after the first day of each month, the Contractor will receive an email or fax notification (“audit notice”) indicating that a representative of its company needs to log-in to the NYSCS to report the company’s MWBE subcontractor and supplier payments for the preceding month. The Contractor must also report when no payments have been made to a subcontractor or supplier in a particular month with entry of a zero dollar value in the NYSCS. Once subcontractor and supplier payments have been entered into the NYSCS, the subcontractor(s) and supplier(s) will receive an email or fax notification advising them to log into the NYSCS to confirm that they actually received the reported payments from the Contractor. It is the Contractor’s responsibility to educate its MWBE subcontractors and suppliers about the NYSCS and the need to confirm payments made to them in the NYSCS. C. To assist in the use of the NYSCS, OGS recommends that all Contractors and MWBE subcontractors and suppliers sign up for the following two webinar trainings offered through the NYSCS: “Introduction to the System – Vendor training” and “Contract Compliance Reporting - Vendor Training” to become familiar with the NYSCS. To view the training schedule and to register visit: xxxxx://xx.xxxxxxxxxxxxxx.xxx/events.asp D. As soon as possible after the Contract is approved, Contractor should visit xxxxx://xx.xxxxxxxxxxxxxx.xxx and click on “Account Lookup” to identify the Contractor’s account by company name. Contact information should be reviewed and updated if necessary by choosing “Change Info.” It is important that the staff member who is responsible for reporting payment information for the Contractor be listed as a user in the NYSCS. Users who are not already listed may be added through “Request New User.” When identifying the person responsible, please add “- MWBE Contact” after his or her last name (i.e., Xxxx Xxx – MWBE Contact) to ensure that the correct person receives audit notices from the NYSCS. NYSCS Technical Support should be contacted for any technical support questions by clicking on the links for “Contact Us & Support” then “Technical Support” on the NYSCS website. E. If Contractor is unable to report MWBE Contractor Compliance via the NYSCS, Contractor must submit a Monthly MWBE Contractor Compliance Report on Form MWBE 102 to OGS, by the 10th day of each month during the term of the Contract, for the preceding month’s activity to: OGS MWBE Office, 00xx Xxxxx Xxxxxxx Xxxxx, Xxxxxx Xxxxx Xxxxx, Xxxxxx, XX 00000. Phone: 000-000-0000; Fax: 000-000-0000. F. It is the Contractor’s responsibility to report subcontractor and supplier payments. Failure to respond to payment audits in a timely fashion through the NYSCS, or by paper to OGS, may jeopardize future payments pursuant to the MWBE liquidated damages provisions in clause IX below.

  • Signaling protocol The Parties will interconnect their networks using SS7 signaling where Technically Feasible and available as defined in GR 905 Telcordia Standards including ISDN User Part (ISUP) for trunk signaling and TCAP for CCS-based features in the Interconnection of their networks. All Network Operations Forum (NOF) adopted standards shall be adhered to. Where available, CenturyLink signaling services to link its Signaling Transfer Points (STPs) for CLEC switches which connect to CenturyLink’s STPs via “A” links or for CLEC’s STPs to connect to CenturyLink’s STPs via “D” links which are dedicated to the transport of signaling for local Interconnection, may be ordered from the CenturyLink Tariff.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!