Converter. Any device changing the frequency of a Signal. A Subscriber Converter may expand reception capacity and/or unscramble coded Signals distributed over the Cable System.
Converter. Any device altering a Signal coming to a Subscriber. A Subscriber Converter may control reception capacity and/or unscramble coded Signals distributed over the Cable System, among other capabilities.
Converter. A device capable of unscrambling coded video signals distributed over the Cable System.
Converter. A special tuner or device attached to the Subscriber’s television set that expands reception capacity and/or unscrambles coded signals distributed over the Cable System.
Converter. An electronic device which converts signals delivered on the Cable System to a frequency not normally susceptible to interference within the television receiver of a Subscriber and any Channel selector which permits a Subscriber to view all signals delivered at designated converter dial locations at the set or by remote control.
Converter. Any device changing the frequency of a Signal. A Subscriber Converter may expand reception capacity and/or unscramble coded Signals distributed over the Cable System, among other capabilities. Response: By way of formal response to this specific section, Comcast refers to its Informal Renewal Proposal, Tab 3, DRAFT Renewal Cable Television License filed on March 09, 2016. Comcast is open to informal negotiations to agree upon language acceptable to both parties.
Converter. A device which may be provided by the Cable Operator to Subscribers for the purpose of changing the frequency of midband, superband, or hyperband signals to a suitable Channel or Channels which the television receiver is able to deliver at designated dial locations.
Converter. I (sometimes referred to herein as the "Converter") hereby agree to acquire the Shares pursuant to Regulation S from mLight Tech, Inc., a Florida corporation (the "Company”), on the terms and conditions described herein.
Converter. The air-cooled IGBT converter operates in a four-quadrant mode. Output voltage and frequency of the generator/converter system are regulated by controlling the exciting current and frequency of the rotor winding. This is achieved by a microprocessor controlled power electronic controller, which triggers the IGBT elements using a pulse width modulation technique so that an almost pure sinusoidal voltage is produced at the output. Table 6. Technical data - converter Unit Value Construction IGBT converter Type of modulation Pulse width modulation Operating mode Four-quadrant operation Kimax = Imax / Ing 1.1 Flicker coefficient approx. <10 Harmonic distortion factor % approx. 1 8 Grid connection The generator output at 690V is stepped up for grid connection by an output transformer. The output transformer provides the connection to the required collector network. The transformer is of the hermetically sealed, liquid immersed type constructed to IEC 60076. The coolant comprises a synthetic oil that is non-toxic and biodegradable, having a low flammability characteristic. Connection of the system to the grid is made after synchronisation through a power switch that also includes protective functions in the event of overload or short-circuit. A three-phase mains monitoring relay is used to monitor voltage and frequency deviations. Power surge and undervoltage, over-frequency and under-frequency, brief interruptions, current asymmetry and phase relationships are monitored. In the event of deviations, the wind turbine will be automatically disconnected from the grid and reconnected as required to meet the local requirements.
Converter. GT has a 1 year option from the date of signing of this agreement to purchase the Converter. However if PE identifies a customer wanting it sooner upon the same terms and conditions as those offered to GT, PE will notify GT in writing and GT will, within 15 days from notification, either exercise the option or renounce it. In case GT will not exercise this option or notify his decision within 15 days PE will be free to proceed with this customer. However this option is not applicable for Companies mentioned in Article 3. [***] GT undertakes to supply suitable bank guarantees upon first request, issued by a bank and having a text acceptable by PE, for the payments of the sums indicated above within 30 days of the signing of this agreement. Failure to do this could lead to the cancellation of the contract by PE. GT is responsible for all expenses related to the manufacture of the prototype components—Chamber and Power Supply. If constructed in Italy the supervision of the prototype component will be at PE's expense. If a component is constructed outside of Italy, GT will be responsible for all expenses incurred by PE for supervision of that prototype component.
