EMBEDDED PARTS. The Supervisor may carry out a check on the setting of all embedded parts prior to concreting of the relevant structures. Concreting work shall not proceed until this check has been carried out.
EMBEDDED PARTS Sample Clauses
Related to EMBEDDED PARTS
Embedded Software To the extent any goods contain Embedded Software (defined below) that is not Buyer’s Property, no title to such Embedded Software shall pass to Buyer, and Supplier shall grant Buyer, its customers and all other users a non-exclusive worldwide, irrevocable, perpetual, royalty-free right to use, load, install, execute, demonstrate, market, test, resell, sublicense and distribute such Embedded Software as an integral part of such goods or for servicing the goods (the “Buyer-Required License”). If such Embedded Software or any part thereof is owned by a third party, prior to delivery, Supplier shall obtain the Buyer-Required License from such third-party owner. “Embedded Software” means software necessary for operation of goods and embedded in and delivered as an integral part of goods.
Spare Parts 14.1 As specified, the supplier may be required to provide any or all of the following materials, notifications, and information pertaining to spare parts manufactured or distributed by the supplier: (a) such spare parts as the purchaser may elect to purchase from the supplier, provided that this election shall not relieve the supplier of any warranty obligations under the contract and; (b) In the event of termination of production of the spare parts: (i) advance notification to the purchaser of the pending termination, in sufficient time to permit the purchaser to procure needed requirements and; (ii) Following such termination, furnishing at no cost to the purchaser, the blueprints, drawings, and specifications of the spare parts, if requested.
REPAIRED OR REPLACED PARTS / COMPONENTS Where the Contractor is required to repair, replace or substitute Product or parts or components of the Product under the Contract, the repaired, replaced or substituted Products shall be subject to all terms and conditions for new parts and components set forth in the Contract including Warranties, as set forth in the Additional Warranties Clause herein. Replaced or repaired Product or parts and components of such Product shall be new and shall, if available, be replaced by the original manufacturer’s component or part. Remanufactured parts or components meeting new Product standards may be permitted by the Commissioner or Authorized User. Before installation, all proposed substitutes for the original manufacturer’s installed parts or components must be approved by the Authorized User. The part or component shall be equal to or of better quality than the original part or component being replaced.
Operator Materials Operator retains all right, title and interest in and to any and all of Operator’s software, materials, tools, forms, documentation, training and implementation materials and intellectual property (“Operator Materials”). Operator grants to the LEA a personal, nonexclusive license to use the Operator Materials for its own non-commercial, incidental use as set forth in the Service Agreement. Operator represents that it has all intellectual property rights necessary to enter into and perform its obligations in this DPA and the Service Agreement, warrants to the District that the District will have use of any intellectual property contemplated by the Service Agreement free and clear of claims of any nature by any third Party including, without limitation, copyright or patent infringement claims, and agrees to indemnify the District for any related claims.
Raw Materials A. Catalent shall procure Raw Materials only from vendors that are approved in writing by Palatin or otherwise qualified in accordance with the provisions of the Quality Agreement. Catalent shall be responsible for procuring Raw Materials as necessary to meet the Firm Commitment. Catalent shall not be liable for any delay in delivery of Product if (i) Catalent is unable to obtain, in a timely manner, a particular Raw Material necessary for Processing and (ii) Catalent placed orders for such Raw Materials promptly following receipt of Palatin’s Firm Commitment. In the event that any Raw Material becomes subject to purchase lead time beyond the Firm Commitment time frame, the parties will negotiate in good faith an appropriate amendment to this Agreement, including Clause 4.2. B. In certain instances, Palatin may require a specific supplier, manufacturer or vendor (“Vendor”) to be used for Raw Material. In such an event, (i) such Vendor will be identified in the Specifications and (ii) the Raw Materials from such Vendor shall be deemed Palatin-supplied Materials for purposes of this Agreement. If the cost of the Raw Material from any such Vendor (other than a Vendor specified in the Specifications as of the Effective Date) is greater than Catalent’s costs for the same raw material of equal quality from other vendors, Catalent shall add the difference between Catalent’s cost of the Raw Material and the Vendor’s cost of the Raw Material to the Unit Pricing. Palatin will be responsible for all reasonable, out-of-pocket costs incurred by Catalent associated with qualification of any such Vendor who has not been previously qualified by Catalent. C. In the event of (i) a Specification change for any reason, (ii) obsolescence of any Raw Material or (iii) termination or expiry of this Agreement, Palatin shall bear the cost of any unused Raw Materials (including packaging), so long as Catalent (a) purchased such Raw Materials in quantities consistent with Palatin’s then current Firm Commitment and any minimum purchase obligations required by the vendor and (b) used commercially reasonable efforts to mitigate such costs by using any such unused Raw Materials in the manufacture of other products.
Accessories, Spare Parts and Tools Accessories, spare parts and tools dispatched with a piece of equipment, machine, apparatus or vehicle, which are part of the normal equipment and included in the price thereof or which are not separately invoiced, shall be regarded as one with the piece of equipment, machine, apparatus or vehicle in question.
Product Information EPIZYME recognizes that by reason of, inter alia, EISAI’s status as an exclusive licensee in the EISAI Territory under this Agreement, EISAI has an interest in EPIZYME’s retention in confidence of certain information of EPIZYME. Accordingly, until the end of all Royalty Term(s) in the EISAI Territory, EPIZYME shall keep confidential, and not publish or otherwise disclose, and not use for any purpose other than to fulfill EPIZYME’s obligations, or exercise EPIZYME’s rights, hereunder any EPIZYME Know-How Controlled by EPIZYME or EPIZYME Collaboration Know-How, in each case that are primarily applicable to EZH2 or EZH2 Compounds (the “Product Information”), except to the extent (a) the Product Information is in the public domain through no fault of EPIZYME, (b) such disclosure or use is expressly permitted under Section 9.3, or (c) such disclosure or use is otherwise expressly permitted by the terms and conditions of this Agreement. For purposes of Section 9.3, each Party shall be deemed to be both the Disclosing Party and the Receiving Party with respect to Product Information. For clarification, the disclosure by EPIZYME to EISAI of Product Information shall not cause such Product Information to cease to be subject to the provisions of this Section 9.2 with respect to the use and disclosure of such Confidential Information by EPIZYME. In the event this Agreement is terminated pursuant to Article 12, this Section 9.2 shall have no continuing force or effect, but the Product Information, to the extent disclosed by EPIZYME to EISAI hereunder, shall continue to be Confidential Information of EPIZYME, subject to the terms of Sections 9.1 and 9.3 for purposes of the surviving provisions of this Agreement. Each Party shall be responsible for compliance by its Affiliates, and its and its Affiliates’ respective officers, directors, employees and agents, with the provisions of Section 9.1 and this Section 9.2.
Consumables During the design phase, Purchaser may participate in the selection of suppliers of consumables of the Supplier. In such case, the choice regarding the final selection of the said suppliers shall be mutually agreed between the Parties. Two suppliers shall be identified and selected for each type of consumables.
COMMERCIAL COMPUTER SOFTWARE If performance involves acquisition of existing computer software, the following Company Exhibit is incorporated by reference: CCS Commercial Computer Software License (Company – July 2010).
Equipment and Materials CONTRACTOR shall provide all equipment, materials, and supplies necessary for the performance on the Agreement except:
