Final Completion The full and final completion of all Work in accordance with the Contract Documents.
Test The outer surface of the lamp lenses shall be subjected once or more than once to the action of the sand jet produced as described above. The jet shall be sprayed almost perpendicular to the surface to be tested. The deterioration shall be checked by means of one or more samples of glass placed as a reference near the lenses to be tested. The mixture shall be sprayed until the variation in the diffusion of light on the sample or samples measured by the method described in Appendix 2, is such that: Δ d = (T5 - T4) / T2 ≤ 0.0250 ± 0.0025 Several reference samples may be used to check that the whole surface to be tested has deteriorated homogeneously. Annex 6 - Appendix 4
CERTIFICATION OF INDEPENDENT PRICE DETERMINATION By submission of this bid, the Bidder certifies, and in the case of a joint bid each party thereto certifies as to its own organization, that in connection with this procurement:
Final Evaluation IC must submit a final report and a project evaluation to the Arts Commission within thirty (30) days after the completion of the Services. Any and all unexpended funds from IC must be returned to City no later than sixty (60) days after the completion of the Services.
Independent Evaluation Buyer is an experienced and knowledgeable investor in the oil and gas business. Buyer has been advised by and has relied solely on its own expertise and legal, tax, title, reservoir engineering, environmental and other professional counsel concerning this transaction, the Properties, the value thereof and title thereto.
Regulatory Good Standing Certification - Explanation - Continued If Vendor responded to the prior attribute that "No", Vendor is not in good standing, Vendor must provide an explanation of that lack of good standing here for TIPS consideration. No response
SPECIAL CONDITION With respect to Liability to the Fund or its shareholders, and subject to applicable state and federal law, the Board Member shall be indemnified pursuant to this Section 1 against any Liability unless such Liability arises by reason of the Board Member’s willful misfeasance, bad faith, gross negligence, or reckless disregard of the duties involved in the conduct of his or her office as defined in such Section 17(h) of the Investment Company Act of 1940, as amended (“Disabling Conduct”).
Financial Condition There shall have been no material adverse change, as determined by Bank, in the financial condition or business of Borrower, nor any material decline, as determined by Bank, in the market value of any collateral required hereunder or a substantial or material portion of the assets of Borrower.
Allowable Costs and Audit Requirements 11 4.1 ALLOWABLE COSTS 11 4.2 AUDITS AND FINANCIAL STATEMENTS 11 4.3 SUBMISSION OF AUDITS AND FINANCIAL STATEMENTS 12 ARTICLE V. WARRANTY, AFFIRMATIONS, ASSURANCES AND CERTIFICATIONS 12 5.1 WARRANTY 12 5.2 GENERAL AFFIRMATIONS 13 5.3 FEDERAL ASSURANCES 13 5.4 FEDERAL CERTIFICATIONS 13 5.5 STATE ASSURANCES 13 ARTICLE VI. INTELLECTUAL PROPERTY 13 6.1 OWNERSHIP OF WORK PRODUCT 13 6.2 GRANTEE’S PRE-EXISTING WORKS 14 6.3 THIRD PARTY IP 14 6.4 AGREEMENTS WITH EMPLOYEES AND SUBCONTRACTORS 14 6.5 DELIVERY UPON TERMINATION OR EXPIRATION 14 6.6 SURVIVAL 15 6.7 SYSTEM AGENCY DATA 15 ARTICLE VII. PROPERTY 15
Meter Testing Company shall provide at least twenty-four (24) hours' notice to Seller prior to any test it may perform on the revenue meters or metering equipment. Seller shall have the right to have a representative present during each such test. Seller may request, and Company shall perform, if requested, tests in addition to the every fifth-year test and Seller shall pay the cost of such tests. Company may, in its sole discretion, perform tests in addition to the fifth year test and Company shall pay the cost of such tests. If any of the revenue meters or metering equipment is found to be inaccurate at any time, as determined by testing in accordance with this Section 10.2 (Meter Testing), Company shall promptly cause such equipment to be made accurate, and the period of inaccuracy, as well as an estimate for correct meter readings, shall be determined in accordance with Section 10.3 (Corrections).
