BILLING PROCEDURES AND PAYMENT COMMERCE shall reimburse the Contractor for eligible Project expenditures, up to the maximum payable under this Contract. When requesting reimbursement for expenditures made, Contractor shall submit all Invoice Vouchers and any required documentation electronically through COMMERCE’s Contracts Management System (CMS), which is available through the Secure Access Washington (SAW) portal. If the Contractor has constraints preventing access to COMMERCE’s online A-19 portal, a hard copy A-19 form may be provided by the COMMERCE Project Manager upon request. The voucher must be certified by an official of the Contractor with authority to bind the Contractor. The final voucher shall be submitted to COMMERCE no later than November 15, 2020. COMMERCE will pay Contractor upon acceptance of services provided and receipt of properly completed invoices, which shall be submitted to the Representative for COMMERCE not more often than monthly. The invoices shall describe and document, to COMMERCE's satisfaction, reimbursable expenditures as set forth under the Scope of Work (Attachment A) and Budget & Invoicing (Attachment B). The invoice shall include the Contract Number as stated on the Face Sheet. Each voucher must be accompanied by an A-19 Certification (Attachment C) and A-19 Activity Report (Attachment D). The A-19 Certification must be certified by an authorized party of the Contractor to certify and attest all expenditures submitted on the voucher are in compliance with the United States Treasury Coronavirus Relief Fund (“Fund”) Guidance for State, Territorial, Local, and Tribal Governments: xxxxx://xxxx.xxxxxxxx.xxx/system/files/136/Coronavirus-Relief-Fund-Guidance-for-State-Territorial-Local- and-Tribal-Governments.pdf The A-19 Activity Report must be submitted which describes, in Excel spreadsheet and narrative form, a detailed breakdown of the expenditures within each applicable budget sub-category identified in the voucher, as well as a report of expenditures to date. COMMERCE will not release payment for any reimbursement request received unless and until the A-19 Certification and A-19 Activity Report is received. After approving the Invoice Voucher, A-19 Certification and Activity Report, COMMERCE shall promptly remit a warrant to the Contractor. Payment shall be considered timely if made by COMMERCE within thirty (30) calendar days after receipt of properly completed invoices. Payment shall be sent to the address designated by the Contractor. COMMERCE may, in its sole discretion, terminate the Contract or withhold payments claimed by the Contractor for services rendered if the Contractor fails to satisfactorily comply with any term or condition of this Contract. No payments in advance or in anticipation of services or supplies to be provided under this Agreement shall be made by COMMERCE.
Taxes and Fees Imposed on Purchasing Party But Collected And Remitted By Providing Party 11.3.1 Taxes and fees imposed on the purchasing Party shall be borne by the purchasing Party, even if the obligation to collect and/or remit such taxes or fees is placed on the providing Party.
Billing and Payment Procedures and Final Accounting 6.1.1 The Connecting Transmission Owner shall xxxx the Interconnection Customer for the design, engineering, construction, and procurement costs of Interconnection Facilities and Upgrades contemplated by this Agreement on a monthly basis, or as otherwise agreed by those Parties. The Interconnection Customer shall pay all invoice amounts within 30 calendar days after receipt of the invoice.
CERTIFICATION PROHIBITING DISCRIMINATION AGAINST FIREARM AND AMMUNITION INDUSTRIES (Texas law as of September 1, 2021) By submitting a proposal to this Solicitation, you certify that you agree, when it is applicable, to the following required by Texas law as of September 1, 2021: If (a) company is not a sole proprietorship; (b) company has at least ten (10) full-time employees; (c) this contract has a value of at least $100,000 that is paid wholly or partly from public funds; (d) the contract is not excepted under Tex. Gov’t Code § 2274.003 of SB 19 (87th leg.); and (e) governmental entity has determined that company is not a sole-source provider or governmental entity has not received any bids from a company that is able to provide this written verification, the following certification shall apply; otherwise, this certification is not required. Pursuant to Tex. Gov’t Code Ch. 2274 of SB 19 (87th session), the company hereby certifies and verifies that the company, or association, corporation, partnership, joint venture, limited partnership, limited liability partnership, or limited liability company, including a wholly owned subsidiary, majority-owned subsidiary parent company, or affiliate of these entities or associations, that exists to make a profit, does not have a practice, policy, guidance, or directive that discriminates against a firearm entity or firearm trade association and will not discriminate during the term of this contract against a firearm entity or firearm trade association. For purposes of this contract, “discriminate against a firearm entity or firearm trade association” shall mean, with respect to the entity or association, to: “(1) refuse to engage in the trade of any goods or services with the entity or association based solely on its status as a firearm entity or firearm trade association; (2) refrain from continuing an existing business relationship with the entity or association based solely on its status as a firearm entity or firearm trade association; or (3) terminate an existing business relationship with the entity or association based solely on its status as a firearm entity or firearm trade association. See Tex. Gov’t Code § 2274.001(3) of SB 19. “Discrimination against a firearm entity or firearm trade association” does not include: “(1) the established policies of a merchant, retail seller, or platform that restrict or prohibit the listing or selling of ammunition, firearms, or firearm accessories; and (2) a company’s refusal to engage in the trade of any goods or services, decision to refrain from continuing an existing business relationship, or decision to terminate an existing business relationship to comply with federal, state, or local law, policy, or regulations or a directive by a regulatory agency, or for any traditional business reason that is specific to the customer or potential customer and not based solely on an entity’s or association’s status as a firearm entity or firearm trade association.” See Tex. Gov’t Code § 2274.001(3) of SB 19.