Mounting and Balancing Sample Clauses

Mounting and Balancing. You will be reimbursed for the reasonable costs that You incur for mounting, balancing, valve stems, and tire disposal for any tire replaced under this Agreement. However, charges for pressure sensing devices and unspecified charges for shop supplies are excluded.
Sample 1Sample 2Sample 3See All (8)
AutoNDA by SimpleDocs
Mounting and Balancing. You will be reimbursed for the reasonable costs that You incur for mounting, balancing, valve stems, and tire disposal for any tire replaced under this Agreement. However, charges for pressure sensing devices and unspecified charges for shop supplies are excluded. • Taxes: You will be reimbursed for the cost of local and state taxes, as directed by state agencies for any tire or wheel replaced under this Agreement.
Sample 1Sample 2Sample 3See All (4)
Mounting and Balancing. You will be reimbursed for the reasonable costs that You incur for mounting, balancing, valve stems, and tire disposal for any tire replaced under this Agreement. However, charges for pressure sensing devices and unspecified charges for shop supplies are excluded. •Taxes: You will be reimbursed for the cost of local and state taxes, as directed by state agencies for any tire or wheel replaced under this Agreement. Customer Initials: AGREEMENT HOLDER RESPONSIBILITY You must maintain proper air pressure in all covered tires. Tires should be checked monthly for proper pressure, signs of dry rot, improper wear, and tread depth less than 3/32". Any conditions that cannot be corrected demands replacement for the safety of the vehicles occupants. Replaced tires are covered for the time remaining on the Agreement. CLAIM PROCEDURES YOU MUST OBTAIN AUTHORIZATION PRIOR TO REPLACEMENT OF ANY TIRE, AND/OR PRIOR TO ANY REPAIR OR REPLACEMENT OF ANY WHEEL. For authorization and instructions please call Our Administrator, NIU of Florida, Inc., at 000-000-0000 Monday through Friday from 9 a.m. to 8 p.m. eastern time. A proof of loss form will be provided which You MUST complete and return to NIU of Florida, Inc. at 000 Xxxxxx Xxxx, Xxxxx 000, Xxxx Xxxxx, Xxxxxxx 00000 within thirty (30) days along with the following documentation: a. Front and back copy of this Agreement; b. Original replacement or repair invoice which must reflect: 1) The tread depth of the damaged tire; 2) Whether or not the damaged tire or wheel was repairable, and if not, why not; 3) Whether or not the damage was due to a manufacturer's defect; c) Original receipts for Emergency Travel Expenses, if applicable; and d) Any other information that the Administrator reasonably requests.
Sample 1
Mounting and Balancing. You will be reimbursed for the cost of mounting, balancing and valve stems for any tire replaced under this Agreement.
Sample 1

Related to Mounting and Balancing

  • TESTING AND COMMISSIONING 24 Allow for a Lump Sum for testing and commissioning of the entire electrical installation, including the provision of Compliance Certificate. Item Carried to Collection R Section No. 4 Electrical Installation (Provisional) Bill No. 1 Electrical Installation COLLECTION Total Brought Forward from Page No. Carried to Final Summary 76 77 R Amount FINAL SUMMARY Section No Page No 1 Preliminaries 26 2 Alterations (Provisional) 30 3 External Works (Provisional) 73

  • Cutting, Patching, and Fitting The Contractor shall do all cutting, patching, and fitting of the Work that may be required to make its several parts come together properly and fit.

  • METERING AND BILLING Metering requirements and billing procedures shall be set forth in the AEC rate schedule(s) applicable to the electric service account assigned to the location where the Generating Facility is connected.

  • BID OPENING AND EVALUATION 25 BID OPENING

  • Skidding and Yarding Methods of skid- ding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and construction clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. B6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees desig- nated for cutting.

  • JOB POSTING AND BIDDING A. Notices of bargaining unit job vacancies, excluding temporary and on-call vacancies, shall be posted on the bulletin board at each facility for a period of three (3) business days prior to filling the vacancy. The Notice should include the job requirements specific to the position being posted. The full and complete minimum requirements for the position will be maintained by the personnel representative for disclosure to applicants at the time of bid.

  • Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. Purchaser may buck out cull material when necessary to produce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchantability factor, whichever is stated in A2. If necessary to assess extent of defect, Purchaser shall make sample saw cuts or wedges. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.

  • Retraining and Adjustment Period (1) Employees who assume a new position pursuant to this article will receive job orientation, including, where deemed appropriate by the Joint Committee, current in-service training, and shall be allowed a reasonable time to familiarize themselves with their new duties.

  • Weighing and Scaling Costs Purchaser agrees to pay for all weighing costs for logs delivered regardless if logs are purchased on a weight or scale basis. In addition, Purchaser agrees to pay for all scaling costs for logs delivered on a scale basis. Purchaser also agrees to pay for all costs associated with the transmission and reporting of scale or weight data.

  • Parking and Transportation ‌ The Union agrees that during the life of this Agreement, the University may apply changes in transportation policy, including adjusting parking and U-Pass fees and criteria for assigning parking spots, to the bargaining unit without the obligation to bargain with the Union. The Union may raise issues and concerns about the University’s parking program at Joint Labor/Management Committee meetings or at ad hoc Labor Management Committee meetings. The Union shall have a standing seat on the University’s committee(s) that work on transportation and parking issues.

Time is Money Join Law Insider Premium to draft better contracts faster.