Other Measurement Standards Sample Clauses

Other Measurement Standards. The following provisions will apply with respect to Delivery Points that are not part of the Xxxx Inlet Gas Distribution System: (A) Seller shall, at its expense, provide continuous data showing Gas delivery rates for each such Delivery Point, if so requested by Buyer, when such Delivery Point is owned, maintained and operated by Seller. Seller shall have the right to refuse to tender Gas for delivery to Buyer at any Delivery Point that is not operating properly or measuring volumes of Gas accurately; provided, that such refusal shall not alter Seller’s obligations to make available and deliver Gas to Buyer under Section 2. Hilcorp Alaska, LLC, and Chugach Electric Association, Inc. (B) If a meter at such a Delivery Point is out of service or registering inaccurately by a variation greater than one percent (1%), the volumes of Gas delivered shall be estimated: (1) by using the volumes registered by the check meter or meters of Seller, if installed and accurately registering, or (2) in the absence of estimation pursuant to clause (1), by correcting the error if the percentage of error is ascertainable by calibration, test or mathematical calculations, or (3) in the absence of estimation pursuant to both clause (1) and clause (2), then by estimating the quantity of deliveries based on deliveries during comparable periods under similar conditions when the meter was registering accurately. (C) If any measuring equipment is found to be inaccurate by one percent (1%) or less, previous records of the equipment shall be considered accurate. If any measuring equipment is found to be inaccurate by more than one percent (1%), any previous records of that equipment, any previous xxxxxxxx will be corrected to zero error for any period known definitely or agreed upon using the estimate obtained via Section 5.2(B) (1), (2) or (3) above (as applicable). If a period of inaccuracy is not definitely known or agreed upon by the Parties, the correction shall be made for a period of one half ( 1⁄2) of the time elapsed since the date of the last test of the meter. The correction shall fully settle all claims based on the inaccuracy. Any measuring equipment found by test to be inaccurate, even if such error is less than one percent (1%), will immediately be adjusted or replaced, as appropriate, to measure accurately. (D) If Buyer notifies Seller that it desires to test the accuracy of a meter at such a Delivery Point, Seller will test the accuracy of the measuring equipment promp...
Sample 1
AutoNDA by SimpleDocs

Related to Other Measurement Standards

  • Procurement Standards For projects being managed by the Local Government and on the State highway system or that include state funding, the Local Government must obtain approval from the State for its proposed procurement procedure for the selection of a professional services provider, a contractor for a construction or maintenance project, or a materials provider.

  • Development Standards For any structure built on the Property following the Effective Date, it shall comply with the requirements contained in Exhibit B, “Building Materials,” attached hereto and incorporated herein. The Parties agree and acknowledge that the provisions of this Paragraph shall apply to any structure constructed subsequent to the execution of this Agreement. Nothing in this Agreement shall be deemed to modify or otherwise amend any zoning regulation duly adopted by the Town, previously or in the future.

  • Content Standards You agree that you will not upload or provide content or otherwise post, transmit, distribute, or disseminate through the Zelle® Payment Service any material that: (1) is false, misleading, unlawful, obscene, indecent, lewd, pornographic, defamatory, libelous, threatening, harassing, hateful, abusive, or inflammatory; (2) encourages conduct that would be considered a criminal offense or gives rise to civil liability; (3) breaches or infringes any duty toward or rights of any person or entity, including rights of publicity, privacy or intellectual property; (4) contains corrupted data or any other harmful, disruptive, or destructive files; (5) advertises products or services competitive with Zelle®, as determined by Zelle® in its sole discretion; or (6) in Zelle®’s or our sole judgment, is objectionable, restricts or inhibits any person or entity from using or enjoying any portion of the Zelle® Payment Service, or which may expose us, Zelle® or our respective affiliates or customers to harm or liability of any nature.

  • Quality Standards Each Party agrees that the nature and quality of its products and services supplied in connection with the other Party's Marks will conform to quality standards set by the other Party. Each Party agrees to supply the other Party, upon request, with a reasonable number of samples of any Materials publicly disseminated by such Party which utilize the other Party's Marks. Each Party will comply with all applicable laws, regulations, and customs and obtain any required government approvals pertaining to use of the other Party's marks.

  • Corrective Measures If the Participating Generator fails to meet or maintain the requirements set forth in this Agreement and/or the CAISO Tariff, the CAISO shall be permitted to take any of the measures, contained or referenced in the CAISO Tariff, which the CAISO deems to be necessary to correct the situation.

  • Manufacturing Standards All forest products except poles, produced and sold under this contract will be manufactured to maximize the amount of logs meeting preferred log lengths and to achieve the average log length listed. 97318 3 WS "WS" indicates that west side scaling rules apply. Minimum trim is 8 inches per scaling segment for west side scaling rules. "ES" indicates that east side scaling rules apply. Minimum trim is 4 inches per scaling segment for east side scaling rules. Poles produced under this contract will be manufactured to ANSI specifications (American National Standard Specifications and Dimensions for Wood Poles), in force at the time of signing this contract. a. Sweep will be limited to within the bole of the log as measured using a tape stretched between the centers of each end of the log. b. Logs approved by the state for peelers shall be chuckable with no more than a 2 inch diameter area of rot within a 5 inch diameter circle located at the center of either end of the log. c. Limbs and knots shall be cut flush, with no more than 15 percent of a log having limbs or knots over 2 inches in diameter extending more than 2 inches above the surface of the log.

  • Usage Measurement Usage measurement for calls shall begin when answer supervision or equivalent Signaling System 7 (SS7) message is received from the terminating office and shall end at the time of call disconnect by the calling or called subscriber, whichever occurs first.

  • Hot Weather Guidelines For the purposes of site based discussions regarding the need to plan and perform work during expected periods of hot weather, the following issues shall be considered in conjunction with proper consideration of Occupational Health and Safety issues.

  • Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.

  • OMB Standards Unless specified otherwise within this agreement, the Subrecipient shall procure all materials, property, or services in accordance with the requirements of 24 CFR 84.40−48.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!