Quality Check Points Sample Clauses

Quality Check Points. ‌ Developer shall establish quality control checkpoints (QCPs) at stages of the construction progress to ensure Work is performed in accordance with Developer’s Construction QA/QC Plan and within the terms and conditions of the East End Crossing. As Work is accomplished, Developer’s Quality Manager and Lead Engineer shall meet with the IFA to review documentation and procedures for QA/QC, including but not limited to material certifications, daily inspection records, material testing results, survey results, permits, and material placement records. Developer’s Quality Manager shall coordinate group members to ensure that QCPs are accomplished in a timely manner so that Developer is not delayed. When an identified QCP is accomplished and when notified by the Quality Manager, IFA will respond within four working hours to verify whether Work has been completed for the checkpoint. Notification to IFA that a QCP has been reached while Work is still being performed or not allowing adequate time to complete the QCP review and opportunity for adjustments (e.g., concrete trucks are queuing while reinforcement is still being placed and QCP is being reviewed for a specified unit) will result in the issuance of a Nonconformance Report. At a minimum, Developer shall establish QCPs at the following stages of construction:
Sample 1Sample 2Sample 3See All (5)
AutoNDA by SimpleDocs

Related to Quality Check Points

  • Quality Management System Supplier hereby undertakes, warrants and confirms, and will ensue same for its subcontractors, to remain certified in accordance with ISO 9001 standard or equivalent. At any time during the term of this Agreement, the Supplier shall, if so instructed by ISR, provide evidence of such certifications. In any event, Supplier must notify ISR, in writing, in the event said certification is suspended and/or canceled and/or not continued.

  • Contact Points 1. Each Party shall designate a contact point to facilitate communications between the Parties on any matter covered by this Agreement. 2. Upon request of the other Party, the contact point shall identify the office or official responsible for the matter and assist, as necessary, in facilitating communication with the requesting Party. Contact points shall work jointly to develop agendas and make other preparations for the Free Trade Commission meetings and follow-up on the Free Trade Commission's decisions as appropriate; provide administrative support to the Panels established under Chapter 15 (Dispute Settlement) and address any other matter entrusted by the Free Trade Commission.

  • STATEWIDE CONTRACT MANAGEMENT SYSTEM If the maximum amount payable to Contractor under this Contract is $100,000 or greater, either on the Effective Date or at any time thereafter, this section shall apply. Contractor agrees to be governed by and comply with the provisions of §§00-000-000, 00-000-000, 00-000-000, and 00- 000-000, C.R.S. regarding the monitoring of vendor performance and the reporting of contract information in the State’s contract management system (“Contract Management System” or “CMS”). Contractor’s performance shall be subject to evaluation and review in accordance with the terms and conditions of this Contract, Colorado statutes governing CMS, and State Fiscal Rules and State Controller policies.

  • Quality Management Grantee will:

  • Minimum Customer Support Requirements for TIPS Sales Vendor shall provide timely and commercially reasonable support for TIPS Sales or as agreed to in the applicable Supplemental Agreement.

  • Attachment A, Scope of Services The scope of services is amended as follows:

  • Focal Points ‌ In accordance with CCR §7364(a)(5) County will specify to Subrecipient the identity of the Area Plan designated focal points for service delivery in the community which is attached hereto as Exhibit 6 and is hereinafter referred to as Exhibit 6. THE REMAINDER OF THIS PAGE WAS INTENTIONALLY LEFT BLANK

  • Quality Control A. Controlled Affiliate agrees to use the Licensed Marks and Name only in connection with the licensed services and further agrees to be bound by the conditions regarding quality control shown in attached Exhibit A as they may be amended by BCBSA from time-to-time.

  • Quality control system (i) The Contractor shall establish a quality control mechanism to ensure compliance with the provisions of this Agreement (the “Quality Assurance Plan” or “QAP”).

  • Check Meters Developer, at its option and expense, may install and operate, on its premises and on its side of the Point of Interconnection, one or more check meters to check Connecting Transmission Owner’s meters. Such check meters shall be for check purposes only and shall not be used for the measurement of power flows for purposes of this Agreement, except as provided in Article 7.4 below. The check meters shall be subject at all reasonable times to inspection and examination by Connecting Transmission Owner or its designee. The installation, operation and maintenance thereof shall be performed entirely by Developer in accordance with Good Utility Practice.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!