REINFORCING Sample Clauses

REINFORCING. PSG 5.1.2 Fixing
AutoNDA by SimpleDocs
REINFORCING. The prices/ rates for steel reinforcing shall include for the supply, cutting, bending, lowering and hoisting of reinforcing to the various work areas, placing and wiring in position with and including 1.60 or 1.25mm diameter annealed wire, spacer blocks shall be deemed to be included in the rates / prices of the reinforcing. Prices/ rates for fabric reinforcing shall include for unrolling, cutting, bending and binding wire, and for a minimum of 300mm side and end laps, hoisting or lowering and fixing and maintaining in position. Section No. 3 Bill No. 3 Concrete, Formwork and Reinforcement UNREINFORCED CONCRETE CAST AGAINST EXCAVATED SURFACES 1 Surface blinding under footings m3 1 REINFORCED CONCRETE CAST AGAINST EXCAVATED SURFACES 2 Strip footings m3 7 3 Surface beds cast in panels on waterproofing m3 16 4 Ramps m3 3 5 Steps m3 3 6 Making and testing 150 x 150 x 150mm concrete strength test cubes (Provisional) No 10
REINFORCING. A. Reinforcing Bars: ASTM A615, Grade 60, deformed billet-steel, clean and free from rust, scale, or coating that will reduce bond. B. Welded Wire Fabric: ASTM A185. Tags designating wire size and spacing shall be left on each roll until ready for use.
REINFORCING. No less than one (1) Employee on all concrete pours, walls, mats and floors, wherever reinforcing is in concrete. Where #6 wire mesh or heavier is used, not less than two (2) Employees shall be employed in the cutting and laying, and not less than one (1) Employee in mucking and pulling and maintaining. Employing two (2) men shall only apply where #6 or heavier mesh is used in building work only.
REINFORCING. Reinforcing of sidewalks will not be required except in unusual conditions where the City Engineer may require reinforcing or welded wire fabric. When welded wire fabric is used it shall be placed two inches (2'') from the finished surface of the sidewalk. There will be no direct payment for this item, and it shall be subsidiary to the unit price bid for sidewalk replacement.
REINFORCING. Steel Reinforcement Materials shall conform to the requirements of current Standard Specifications of the Michigan Department of Transportation.
REINFORCING. Steel reinforcement shall comply with the respective Australian Standards AS 1302, AS 1303 and AS 1304.
AutoNDA by SimpleDocs

Related to REINFORCING

  • Dewatering (a) Where the whole of a site is so affected by surface water following a period of rain that all productive work is suspended by agreement of the Parties, then dewatering shall proceed as above with Employees so engaged being paid at penalty rates as is the case for safety rectification work. This work is typically performed by Employees engaged within CW1, CW2 or CW3 classifications. When other Employees are undertaking productive work in an area or areas not so affected then dewatering will only attract single time rates. (b) Where a part of a site is affected by surface water following a period of rain, thus rendering some areas unsafe for productive work, consistent with the Employer’s obligations under the OH&S Act, appropriate Employees shall assist in the tidying up of their own work site or area if it is so affected. Where required, appropriate Employees will be provided with the appropriate PPE. Such work to be paid at single time rates. Productive work will continue in areas not so affected. (c) To avoid any confusion any ‘dewatering’ time which prevents an Employee from being engaged in their normal productive work is not included in any calculation for the purposes of determining whether an Employee is entitled to go home due to wet weather (refer clauses 32.4 and 32.5)

  • Motivation □ Used positive reinforcements with students; motivated and encouraged students to achieve. □ At times used positive reinforcement with students; inconsistent in encouragement of students. □ Little or no use of positive reinforcement or encouragement to succeed.

  • Blasting Blasting shall be permitted only for road construction purposes unless advance permission is obtained from Forest Service. Whenever the Industrial Fire Precaution Level is II or greater, a fire security person equipped with a long handled round point No. 0 or larger shovel and a 5 gallon backpack pump can filled with water, will stay at location of blast for 1 hour after blasting is done. Blasting may be suspended by Forest Service, in areas of high rate of spread and resistance to control. Fuses shall not be used for blasting. Explosive cords shall not be used without permission of Forest Service, which may specify conditions under which such explosives may be used and precautions to be taken.

  • PRODUCTIVITY The Union shall place no limitations upon the amount of work which an Employee shall perform during the working day and there shall be no restrictions imposed against the use of any type of machinery, tools or labour saving devices.

  • Mutuality The Parties acknowledge and declare that this Agreement is the result of extensive negotiations between them. Accordingly, if there is any ambiguity in this Agreement, there shall be no presumption that this instrument was prepared solely by any Party.

  • Appearance The Employee must appear at the Employer’s desired workplace at the time scheduled. If the Employee does not appear, for any reason, on more than separate occasions in a 12-month calendar period the Employer has the right to terminate this Agreement immediately. In such event, the Employee would not be granted severance as stated in Section III.

  • Infrastructure Infrastructure serves as the foundation and building blocks of an integrated IT solution. It is the hardware which supports Application Services (C.3.2) and IT Management Services (C.3.3); the software and services which enable that hardware to function; and the hardware, software, and services which allow for secure communication and interoperability between all business and application service components. Infrastructure services facilitate the development and maintenance of critical IT infrastructures required to support Federal government business operations. This section includes the technical framework components that make up integrated IT solutions. One or any combination of these components may be used to deliver IT solutions intended to perform a wide array of functions which allow agencies to deliver services to their customers (or users), whether internal or external, in an efficient and effective manner. Infrastructure includes hardware, software, licensing, technical support, and warranty services from third party sources, as well as technological refreshment and enhancements for that hardware and software. This section is aligned with the FEA/DoDEA Technical Reference Model (TRM) which describes these components using a vocabulary that is common throughout the entire Federal government. A detailed review of the TRM is provided in Section J, Attachment 5. Infrastructure includes complete life cycle support for all hardware, software, and services represented above, including planning, analysis, research and development, design, development, integration and testing, implementation, operations and maintenance, information assurance, and final disposition of these components. The services also include administration and help desk functions necessary to support the IT infrastructure (e.g., desktop support, network administration). Infrastructure components of an integrated IT solution can be categorized as follows:

  • Logging The ISP will require the maintenance of network and application logs as part of BNY Mellon’s security information and event management processes. Logs are retained in accordance with law applicable to BNY Mellon’s provision of the services as well as BNY Mellon’s applicable policies. BNY Mellon uses various tools in conjunction with such logs, which may include behavioral analytics, security monitoring case management, network traffic monitoring and analysis, IP address management and full packet capture.

  • Fencing The SPD shall Fence the demarcated boundary of the Demised Premises at the SPD’s own expense in every respect.

  • Linking A. Influencer must use “no follow” links in Influencer Content. B. Influencer may embed a hyperlink in the Influencer Content that links to the specific webpage where the third party content is located. Influencers are also responsible for not linking to sites containing content that would not be permitted under the Influencer Agreement.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!