Required Producer-Owned Facilities Sample Clauses

Required Producer-Owned Facilities. Producer will design, permit, construct, own and operate, at Producer’s sole cost and expense, Producer-Owned Facilities. The terminus of Producer-Owned Facilities at the Receipt Point Facilities will be a 4-inch ANSI 300 raised face flange approximately 36” above ground (to centerline), with the exact height and location to be coordinated with NW Natural field engineering personnel, at a pressure to be determined by NW Natural during Phase One. Producer will design and install a pipe and valve assembly, based on industry standards, for collecting Biomethane samples from the flow of gas to the Receipt Point Facilities prior to receipt of Biomethane at the Receipt Point Facilities. Producer will install a minimum of four (4) 1-inch, full bore thread-o-lets, valves, and plugs (exact materials to follow NW Natural specifications and standards and will be approved prior to installation by NW Natural) prior to the terminus of Producer-Owned Facilities at locations mutually agreed upon between Producer and NW Natural, and will allow NW Natural to insert its equipment into the pipeline at these locations. Producer will obtain all necessary permits and authorizations regarding Producer-Owned Facilities and will be solely and fully responsible for compliance with any applicable codes and safety requirements and the inspection, maintenance, and operation of such Producer-Owned Facilities. Additionally, at its sole cost and expense, Producer will design, construct, and maintain at the Plant at all times, the equipment and necessary permits to valve off and immediately flare the Biomethane, or divert flow to other Producer-owned equipment, prior to the terminus flange of Producer-Owned Facilities should NW Natural require Producer to immediately cease all deliveries of Biomethane to the Receipt Point Facilities as described more fully in the Operating Provisions of Article 5 of this Agreement. Producer expressly agrees that Producer is, and NW Natural is not, responsible for the over-pressure protection of Producer-Owned Facilities.
Sample 1Sample 2
AutoNDA by SimpleDocs

Related to Required Producer-Owned Facilities

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CBB chooses to subtend a Verizon access Tandem, CBB’s NPA/NXX must be assigned by CBB to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG.

  • Interconnection Product Options Interconnection Customer has selected the following (checked) type of Interconnection Service:

  • Verizon OSS Facilities Any gateways, interfaces, databases, facilities, equipment, software, or systems, used by Verizon to provide Verizon OSS Services to CBB.

  • Information regarding Interconnection Facilities 4.2.1 The SPD shall be required to obtain all information from the STU/CTU/concerned authority with regard to the Interconnection Facilities as is reasonably necessary to enable it to design, install and operate all interconnection plant and apparatus on the SPD’s side of the Delivery Point to enable delivery of electricity at the Delivery Point. The transmission of power up to the point of interconnection where the metering is done for energy accounting shall be the responsibility of the SPD at his own cost.

  • Prohibition Against Selecting and Installing Products Containing Hazardous Materials The Contractor shall not select, install or otherwise incorporate any products or materials containing Hazardous Materials within the boundaries of the Site. Should the Contractor or any Subcontractors have knowledge that, or believe that, an item, component, material, substance, or accessory within a product or assembly selected by the Contractor or any Subcontractor may contain Hazardous Materials it is the Contractor’s responsibility to secure a written certification from the manufacturer of any suspected material which identifies the specific Hazardous Material(s) contained, together with the Material Safety Data Sheets (MSDS) for such materials which shall be submitted to the Owner and Design Professional.

  • Interconnection Customer Interconnection Facilities Interconnection Customer shall design, procure, construct, install, own and/or control Interconnection Customer Interconnection Facilities described in Appendix A, Interconnection Facilities, Network Upgrades and Distribution Upgrades, at its sole expense.

  • Interconnection Customer’s Interconnection Facilities The Interconnection Customer shall design, procure, construct, install, own and/or control the Interconnection Customer’s Interconnection Facilities described in Appendix A at its sole expense.

  • Underground Facilities All underground pipelines, conduits, ducts, cables, wires, manholes, vaults, tanks, tunnels, or other such facilities or attachments, and any encasements containing such facilities, including without limitation those that convey electricity, gases, steam, liquid petroleum products, telephone or other communications, cable television, water, wastewater, storm water, other liquids or chemicals, or traffic or other control systems.

  • Use of Interconnection Facilities by Third Parties 6551 Error! Hyperlink reference not valid.9.9.1 Purpose of Interconnection Facilities. 6551

  • Interconnection Facilities 4.1.1 The Interconnection Customer shall pay for the cost of the Interconnection Facilities itemized in Attachment 2 of this Agreement. The NYISO, in consultation with the Connecting Transmission Owner, shall provide a best estimate cost, including overheads, for the purchase and construction of its Interconnection Facilities and provide a detailed itemization of such costs. Costs associated with Interconnection Facilities may be shared with other entities that may benefit from such facilities by agreement of the Interconnection Customer, such other entities, the NYISO, and the Connecting Transmission Owner.

Time is Money Join Law Insider Premium to draft better contracts faster.