Selection of Design Alternative(s Sample Clauses

Selection of Design Alternative(s. The Consultant will identify and make rudimentary evaluations of potential design alternative concepts that would meet the Sponsor’s defined project objectives. These evaluations are not to be carried beyond the point of establishing the feasibility of each concept as a design alternative; only those significant environmental and geometric design constraints that bear on the feasibility should be identified. For each concept the Consultant will prepare rudimentary sketches of plan, profile, and typical section views which show: • On plan: proposed centerlines; pavement edges; curve radii and termini; and existing ROW limits. • On profile: theoretical grade lines; critical clearances; vertical curve data; grades; and touchdown points. • On typical section: lane, median, and shoulder widths; ditches; gutters; curbs; and side slopes. • Where necessary: important existing features. • Where pertaining to feasibility: significant environmental and geometric design constraints, labeled as such. These sketches will include only the minimum information needed to select design alternatives to be studied in further detail. The Consultant will meet with the Sponsor to discuss the concepts, using the sketches as discussion aids to describe the relative order-of-magnitude costs, advantages, disadvantages, and problem areas of each. From these concepts the Sponsor will select one, or in some cases more, design alternative(s) for further development.
Sample 1Sample 2See All (5)
AutoNDA by SimpleDocs
Selection of Design Alternative(s. The Consultant will identify and make rudimentary evaluations of potential design alternative concepts that would meet the Sponsor’s defined project objectives. These evaluations are not to be carried beyond the point of establishing the feasibility of each concept as a design alternative; only those significant environmental and geometric design constraints that bear on the feasibility should be identified. For each concept the Consultant will prepare rudimentary sketches of plan, profile and typical section views which show: • On plan: proposed centerlines, pavement edges, curve radii and termini; and existing ROW limits. • On profile: theoretical grade lines; critical clearances; vertical curve data; grades; and touchdown points. • On typical section: lane and shoulder widths; ditches; gutters; curbs and side slopes. • Where necessary: important existing features. • Where pertaining to feasibility: significant environmental and geometric design constraints, labeled as such. These sketches will include only the minimum information needed to select design alternatives to be studied in further detail. The Consultant will meet with the Sponsor to discuss the concepts, using the sketches as discussion aids to describe the relative order-of-magnitude costs, advantages, disadvantages, and problem areas of each. From these concepts the Sponsor will select on, or in some cases more, design alternative(s) for further development.
Sample 1Sample 2

Related to Selection of Design Alternative(s

  • Coordination of Design and Construction Contract Documents 5.5.1 Review model(s), Drawings, Specifications and other Construction Documents as they are developed by A/E during the Schematic Design, Design Development, and Construction Documents design phases of the Project.

  • Release of Design Plan The Engineer (1) will not release any roadway design plan created or collected under this contract except to its subproviders as necessary to complete the contract; (2) shall include a provision in all subcontracts which acknowledges the State’s ownership of the design plan and prohibits its use for any use other than the project identified in this contract; and (3) is responsible for any improper use of the design plan by its employees, officers, or subproviders, including costs, damages, or other liability resulting from improper use. Neither the Engineer nor any subprovider may charge a fee for the portion of the design plan created by the State.

  • If Designated If the HSP is Designated it will:

  • Termination of Designation of Convalescent Care Beds (a) Notwithstanding section 6.3, the provisions in this section 6.5 apply to the termination of a designation of convalescent care Beds.

  • Schematic Design See Section 2, Part 1, Article 2.1.4, Paragraph 2.1.4.2.

  • ELECTRICITY INFORMATION EXCHANGE PROTOCOLS 31.1 Protocols for exchanging information: The Distributor and the Trader must, when exchanging information to which an EIEP listed in Schedule 3 relates, comply with that EIEP.

  • Schematic Design Documents In accordance with the approved Preliminary Design and Construction Schedule and based upon approval of and comments made by the Owner regarding the Concept Design Studies, the Design Professional shall prepare and submit to the Owner Schematic Design Documents, including drawings and outline specifications. These documents shall represent a further development of the approved design concept, providing additional detail and specificity regarding the intended design solution. Typically, all such documents shall be drawn to scale, indicating materials and assemblies, as appropriate, to convey the design intent and to illustrate the Project’s basic elements, scale and relationship to the Site. All major pieces of furniture and equipment to be fixed or supplied by the CM/GC shall be illustrated to scale. (See ASTM Standard Practice E 1804-02, August 2007, Sections 6.3, 8.2 and 8.3 for guidance on information which is generally developed in Schematic Design.)

  • Schematic Design Phase Services § 3.2.1 The Architect shall review the program and other information furnished by the Owner, and shall review laws, codes, and regulations applicable to the Architect’s services.

  • Note to Design Professional Please insert the number of additional Days allowed and the new Material Completion and Occupancy Date, or, if no additional time is allowed, insert “0” for the Days and “No Change” for the date.

  • Design Professional to Design Work The Design Professional Contract requires the Design Professional to design and to prepare the Contract Documents, a copy of which shall be furnished to the Contractor upon request. The Design Professional Contract requires the Design Professional to designate a readily accessible representative (either on Site or by computer, phone or fax or otherwise) who shall have authority promptly to render decisions and to furnish information required of the Design Professional.

Time is Money Join Law Insider Premium to draft better contracts faster.