Sheet Metal and Fabric Flashings Sample Clauses

Sheet Metal and Fabric Flashings. The Roofing Contractor shall furnish and install all Sheet Metal Flashings, Metal Copings, Trim and Roof Accessories as described in the Contract Documents and furnish all exposed Metal through Wall Flashings, including metal reglets for installation by the Masonry Subcontactor. a. Any concealed and exposed (partially into NEW masonry) flashings and any metal flashing requiring a fabricated bend shall be supplied by the Roofing Contractor and installed by the Masonry Contractor at Cavity Walls, Unit Masonry Steel Lintels, Relieving Angle and other areas in contact with Masonry as indicated on the Contract Documents. b. The Roofing Contractor shall furnish and install all Prefinished ZINC Cap, ZINC Fascia and/or Prefinished Aluminum Flashings, Counter Flashings, Copings, Metal Gravel Stops and other Sheet Metal contiguous with the Roofing system. c. The Roofing Contractor shall furnish to the Masonry Contractor, for installation into the Xxxxx’x NEW work, all other Metal Flashing and Metal Thru Wall Flashings as noted in the Contract Documents. d. Membrane Flashings contiguous to the Xxxxx’x work shall be provided and installed by the Xxxxx Contractor. e. The Windows, Glazing and Storefronts Contractor shall furnish and install all Flashings and Sheet Metal that is contiguous with his or her work; such as but not limited to: Flashings required to be installed prior to window or Panel installations. f. The Roofing Contractor shall provide all flashings and reglets and accessories into existing masonry as noted on the Contract Documents. This shall include cutting and patching of all reglets into existing masonry necessary to provide a complete system. g. The Roofing Contractor shall supply to the Masonry Contractor all flashings and reglets and accessories into new masonry and necessary to accept Roofing Contractor’s cap flashing that goes over Roofing Contractor’s termination bar. The Roofing Contractor shall supply the receiver (reglet) to the Masonry Contractor. h. The Roofing Contractor shall supply to the Window Contractor all flashings and reglets and accessories into Window System and necessary to accept Roofing Contractor’s cap flashing that goes over Roofing Contractor’s termination bar. The Roofing Contractor shall supply the receiver (reglet) to the Window Contractor. i. The Roofing Contractor shall supply to the General Trades Contractor all flashings and reglets and accessories into DAFS System and necessary to accept Roofing Contractor’s cap fl...
AutoNDA by SimpleDocs

Related to Sheet Metal and Fabric Flashings

  • Fixtures and Fittings 8.13.1 Not to remove any of the Fixtures and Fittings from the Premises to store the same in the loft, basement or garage (if any) without obtaining the Landlord’s prior written consent, such consent not to be unreasonably withheld, and then to ensure that any such items are stored safely and upon vacating the Premises, to leave the same in the places in which they were on the Commencement Date. 8.13.2 Not to remove the Fixtures and Fittings as specified in the Inventory and Schedule of Condition or any part of them or any substitute Fixtures and Fittings from the Premises and not to bring onto the Premises the Tenant’s own equipment or effects without the prior written consent of the Landlord, such consent not to be unreasonably withheld.

  • Furniture During the Term, at no charge to Subtenant, Subtenant shall be permitted to use the remaining existing modular and office furniture located in the Subleased Premises and described in more particular detail in Exhibit C attached hereto (the “Office Furniture”) as well as all equipment and associated data cabling existing in the Subleased Premises (the Office Furniture together with any equipment and data cabling, being referred to collectively as the “Furniture”). Subtenant shall accept the Furniture in its current condition without any warranty of fitness from Sublandlord (Subtenant expressly acknowledges that no warranty is made by Sublandlord with respect to the condition of any cabling currently located in or serving the Subleased Premises or with respect to the fitness of such cabling for Subtenant’s intend use thereof). For purposes of documenting the current condition of the Office Furniture, Subtenant and Sublandlord shall, within ten (10) days after Sublandlord’s receipt of the Furniture Notice, conduct a joint walk-through of the Subleased Premises in order to inventory items of damage or disrepair. Subtenant shall use the Furniture only for the purposes for which such Furniture is intended and shall be responsible for the proper maintenance, insurance, care and repair of the Furniture, at Subtenant’s sole cost and expense. Subtenant shall not modify, reconfigure or relocate any of the Furniture except with the advance written notice to Sublandlord, and any work of modifying any Furniture (including, without limitation, changing the configuration of, “breaking down” or reassembly of cubicles or other modular furniture) shall be performed at Subtenant’s sole cost. No item of Furniture shall be removed from the Subleased Premises without Sublandlord’s prior written consent.

  • Computer Equipment No computers and/or personal electronic devices, such as tablets and laptop computers, or any component thereof, may be purchased with funds provided under this Contract, regardless of purchase price, without prior written approval of ADMINISTRATOR. Any such purchase shall be in accordance with specifications provided by ADMINISTRATOR, be subject to the same inventory control conditions specified above in Subparagraphs 18.1.1 to 18.1.4, and, at the sole discretion of ADMINISTRATOR, become the property of COUNTY upon termination of this Contract.

  • Customer Equipment “Customer Equipment” means any Customer-owned or provided software, hardware or services that you elect to use in connection with the Service(s). You agree to allow us and our agents the rights to insert CableCARDs and other hardware in the Customer Equipment, send software and/or downloads to the Customer Equipment and install, configure, maintain, inspect and upgrade the Customer Equipment. You warrant you are either the owner of the Customer Equipment or that you have the authority to give us access to the Customer Equipment. You should call Customer Service at 0-000-XXX-XXXX to find out if it meets our technical, security and other requirements. We reserve the right to disallow the use of Customer Equipment that we determine is not compatible with our network. We shall have no obligation to provide, maintain, or service Customer Equipment, including, but not limited to, Customer Equipment to which the Company or a third party has sent software or downloads. If you use Customer Equipment, you agree that the following limitation of liability shall apply: THE COMPANY DOES NOT WARRANT THAT CUSTOMER EQUIPMENT WILL ENABLE YOU TO SUCCESSFULLY INSTALL, ACCESS, OPERATE, OR USE THE SERVICE(S). YOU ACKNOWLEDGE THAT ANY SUCH INSTALLATION, ACCESS, OPERATION, OR USE COULD CAUSE CUSTOMER EQUIPMENT TO FAIL TO OPERATE OR COULD CAUSE DAMAGE TO CUSTOMER EQUIPMENT, YOU, YOUR PREMISES OR COMPANY EQUIPMENT. NEITHER THE COMPANY NOR ANY OF ITS AFFILIATES, SUPPLIERS OR AGENTS SHALL HAVE ANY LIABILITY WHATSOEVER FOR ANY SUCH FAILURE OR DAMAGE, INCLUDING LACK OF 911/E911 CAPABILITY OR DIALING ASSOCIATED WITH A SECURITY SYSTEM. YOUR USE OF CUSTOMER EQUIPMENT MAY PREVENT PROVISION OF SERVICE. The foregoing limitation of liability is in addition to and shall not limit any other limitation of liability set forth in this Agreement.

  • COMMERCIAL COMPUTER SOFTWARE If performance involves acquisition of existing computer software, the following Company Exhibit is incorporated by reference: CCS Commercial Computer Software License (Company – July 2010).

  • Furniture, Fixtures and Equipment Sublessee shall have the right to use during the Term the office furnishings and equipment within the Subleased Premises that are identified on Exhibit C attached hereto, as such exhibit may be adjusted by mutual agreement of the parties prior to the Third Floor Premises Delivery Date (the “Furniture”), provided Sublessee may only use the Furniture located in the Second Floor Premises after the Second Floor Commencement Date. The Furniture is provided in its “AS IS, WHERE IS” condition, without representation or warranty whatsoever. Sublessee shall insure the Furniture under the property insurance policy required under the Master Lease, as incorporated herein, and pay all taxes with respect to the Furniture. Sublessee shall maintain the Furniture in good condition and repair, reasonable wear and tear excepted, and shall be responsible for any loss or damage to the same occurring during the Term. Sublessee shall surrender the Furniture to Sublessor upon the termination of this Sublease in the same condition as exists as of the applicable Delivery Date, reasonable wear and tear excepted. Sublessee shall not remove any of the Furniture from the Subleased Premises. Notwithstanding anything to the contrary herein, Sublessee may provide Sublessor with written notice one (1) time not less than forty-five (45) days prior to the Third Floor Premises Delivery Date that lists any items of Furniture that Sublessee does not want to use and Sublessor shall, at no cost to Sublessee, remove such items from the Subleased Premises prior to the Third Floor Premises Delivery Date and such items shall no longer be considered Furniture hereunder. Notwithstanding the foregoing, provided Sublessee is not in default beyond the expiration of any applicable cure or grace period as of the date of the expiration or earlier termination of this Sublease, which condition may be waived by Sublessor in its sole discretion, then upon the expiration or earlier termination of this Sublease, the Furniture shall become the property of Sublessee, and Sublessee shall accept the same in its “AS IS, WHERE IS” condition, without representation or warranty whatsoever except as provided in the Bill of Sale referred to in the following sentence. In the event the Furniture is to become the property of Sublessee upon the expiration or earlier termination of this Sublease pursuant to the terms of the immediately preceding sentence, then Sublessor agrees to execute and deliver to Sublessee a Bill of Sale in the form of Exhibit D attached hereto conveying and transferring to Sublessee the Furniture.

  • Title to Equipment Title shall vest in the Contractor to all equipment purchased hereunder.

  • Furnishings The Premises is: (check one) ☐ - To be furnished with the following items: [ENTER FURNISHINGS] ☐ - Not furnished.

  • Title to Goods passes to Buyer upon receipt of the Goods at the Buyer- designated location, whether it is an address of the Buyer or of any third party designated by Buyer.

  • Your Equipment All equipment and facilities provided by you for use with your Services is “Customer Equipment.” You are solely responsible for installing, maintaining, configuring, repairing, replacing, upgrading and using your Customer Equipment. Astound has no responsibility whatsoever with respect to your Customer Equipment. If your Customer Equipment impairs the Services, you will remain liable for payment of the applicable Fees for your Services. If, at your request, Xxxxxxx should attempt to resolve difficulties caused by your Customer Equipment, such efforts will be performed at Astound’s discretion and at Astound’s then- current standard hourly rates for such work. Any Customer Equipment you use in connection with the Services must meet Astound’s then-current minimum technical and other requirements.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!