SLEEVES. To be long sleeves with approximate 4 1/2" sleeve vent. Sleeve shall have a one-piece, elbow reinforcement and vent facing. Elbow reinforcement shall extend into the sleeve-closing seam. CUFFS: Forest Green cuffs with set in gold cordedge where cuff is attached to sleeve. Two piece ½-inch hemmed cuff with ¼” topstitching. Cuffs to measure 3” in depth with rounded corners (barrel cuffs). Cuffs to have two buttons and corresponding buttonholes set vertically on the cuff with one button and buttonhole in center of facing. Cuff to have woven interlining of #250 Dacron. BUTTONS: First grade 21-ligne pearlescent. SEWING: Collar and cuffs to be topstitched ¼” off the edge. Shoulder straps and pocket flaps are topstitched along the edge to secure cordedge. Sleeve inserting and side close felling seams are to be safety stitched. THREAD: All sewing threads to be color fast polyester wrap to match. INTERLININGS: Collar, Cuffs, shoulder straps, pocket flaps and top center to be interlined with #250 Dacron. Collar band to be interlined with Crease-N-Tack. MILITARY CREASES: There shall be five silicone sharp military creases on all shirts. One crease on each front to be centered vertically. Front creases shall be through pockets and flaps. Spacing for three military creases across shirt back to be proportionate to the size of the shirt.
SLEEVES. Sleeves are to be straight and whole and to have a ¾” hem and to finish at a minimum of 9 ½” long from shoulder seam. BUTTONS: First grade 21-ligne pearlescent. SEWING: Collar to be topstitched ¼” off the edge. Shoulder straps and pocket flaps are topstitched along the edge to secure cordedge. Sleeve inserting and side close felling seams are to be safety stitched. THREAD: All sewing threads to be color fast polyester wrap to match. INTERLININGS: Collar, shoulder straps, pocket flaps and top center to be interlined with #250 Dacron. MILITARY CREASES: There shall be five silicone sharp military creases on all shirts. One crease on each front to be centered vertically. Front creases shall be through pockets and flaps. Spacing for three military creases across shirt back to be proportionate to the size of the shirt.
SLEEVES. Are straight, two piece set-in sleeves with a stretch mesh underarm panel with a 1/4" double needle topstitch on shell fabric. The cuffs to be 2-1/2” in width and shall have a tab adjustment. Tab shall be pointed, with hook and loop closure. The cuff shall be 1/4” double needled topstitched at the bottom, and 1/16” from the edge of the top. There shall be a sleeve vent opening from the top of the cuff, measuring 4-3/4” long. The vent placket shall be 3/4” wide finished with 1/16” single needle topstitch. The sleeve seam, as well as the sleeve setting seam (i.e. securing it to be body of the shirt) must be made by a narrow safety stitch, so as to properly strengthen the seam, as well as prevent the fabric from xxxxxxxx. Cuffs are to be top fused and fully lined to give body by sewing in a self-fabric inner lining, cut straight to retain its shape.
SLEEVES. Are straight, set-in sleeves, two-piece style of shell & knit, with knit underarm panel, and 1/4" double needle topstitching on shell fabric. Sleeve hem should be clean finished with a 1" hem and 1/16" edge stitch. The sleeve seam, as well as the sleeve setting seam (i.e. securing it to be body of the shirt) must be made by a narrow safety stitch, so as to properly strengthen the seam, as well as prevent the fabric from xxxxxxxx.
SLEEVES. To be straight one-piece set in style with 1” cuffs of self-fabric and lined with 7/8” elastic. The inseam shall be safety stitched. Ribbon loop 1/2” wide by 1-1/4” long is centered over sleeve underarm seam above bottom hem stitch for attachment to Shell System outer jacket. Cuff hem shall finish with 1-3/16” facing of shell fabric and underside of cuff shall be elasticized with 1" elastic.
SLEEVES. Sleeves are shaped two-piece style. There is a sleeve patch made of 1 ply dobby fabric with a 10” zipper to allow access to the shell for emblems and other customization. The cuffs measure 2” in width, half elastic and half not, and to fasten with a 3-3/4” x 1” hook and loop tab. Cuffs are to be interlined with non-woven and elastic to retain its shape. Cuff opening shall be 5-1/4” folded and consist of 1" wide by 5-1/2" long crosswalk reflective tape applied to underside portion of cuff.
SLEEVES. To be long sleeves with approximate 4 1/2" sleeve vent. Sleeve shall have a one-piece, elbow reinforcement and vent facing. Elbow reinforcement shall extend into the sleeve-closing seam and to be set to sleeve with ¼” double needle stitching. CUFFS: Black Cuffs to be two piece ½-inch hemmed cuff with ¼” double needle topstitching. Square cuffs to measure 3" in depth. Cuffs to have two buttonhole eyelets and corresponding buttonholes set vertically on the cuff. Cuff to have woven interlining of #550 Stabilized Xxxxx-Press. BUTTONS: First grade 21-ligne 4 hole pearlescent. SEWING: Shoulder Straps, cuffs, pockets and pocket flaps are ¼” double needle topstitched, including yoke. Collar is single topstitched ¼” off the edge. Side close felling seams and sleeve inserting are also ¼” double needle.
SLEEVES. Sleeves are to be straight and whole and to have a ¾" hem and to finish at a minimum of 9 \/," long from shoulder seam. BUTTONS: First grade 20-ligne melamine. SEWING: Col lar to be topstitched 1/4" off the edg e. Sleeve inserting and side close felling seams are to be safety stitched. THREAD: All sewing threads to be color fast polyester wrap to match. INTERLININGS: Collar and top center to be interlined with woven fusible. AVAILABLE SIZES: Hybrid shirt is available to order in the following sizes: XSMALL –XXXL HYBRID Shirt Specifications Flying Cross Item: 35VS7886 STYLE NUMBER: 35VS7886 FABRlC (A) Upper Body, Sleeves, Collar: Content: 100% Textured Polyester Weight: 7.0 to 7.5 oz. / linear yard Color: Navy FABRIC (B) 37.STM Polvester: Content: 65';-'o COCONA® / 35.5% Polyester Weight: 9.1 oz / Linear Yard Color: Navy STYLE: The Hybrid Shirt shall be manufactured from an up-to-date fonn fitting Shirt pattern. The Hybrid Shirt styling shall have a '/•" front placket with button and buttonhole c closure . COLLAR: Convertible collar shall be one piece. Collar points to measure 2 W' long with ultrasonically fused-in Mylar stays. Collar to have woven fusible interlining. Stays to be 2" long, 3/8" minimum width and to be fused to the bottom ply of the collar and shall be positioned along the leading edge. Collar topstitched 1 / 4” off the edge. UPPER FRONT: Each upper front shall have a facing approximately 3" in width. The left front shall have a top center placket 1-1 /2" wide with two rows of stitches 7/8" apart. Stitching on top - center is not to be visible on the tum-back facing. The shirt will have 3 buttons and buttonholes on the upper front; spacing between each will be 3- ¾" except the spacing between the neck button and the first button on the front, which will be approximately 3-1/4". Top center placket to have woven fusible inter lining. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under , with the front sandwiched between, and then all three are stitched down with a 1 / 16 " raised stitch. Safety stitch joining unacceptable. Inside back yoke to be lined with Nylon Mesh Lining. WOVEN INTERLINING ® PL ACKET LOWER BODY, SIDE PANELS AND UNDERARM GUSSETS: Lower body, side panels and under arm gussets are made from 37.5™ Polyester fabric for ease of movement and comfort when worn under the U1 Carrier.
SLEEVES. To prevent stove-piping the sleeves shall be individually graded by coat size and sleeve length. For maximum freedom, the sleeve design shall feature extra full cut one-piece set-in sleeves with built-in bellows. To reduce the chances of possible top seam failure in that high thermal exposure area, the sleeve Major seams shall follow the underside of the arm and shall t cross over the outside of the elbow joint. Sleeve seam and sleeve attachment to coat body in all layers shall be 100% double xxxx and double stitched for maximum.
SLEEVES. A. Provide standard weight steel pipe sleeves at all points where piping passes through walls, floors, and ceilings, except where otherwise specified.
