Warrington Pro. All boots to be OSHA approved and NFPA compliant, steel toe, non-slip heel and sole.
Warrington Pro Sample Clauses
Related to Warrington Pro
Caisson Rock Caisson Rock is defined as material that must be removed from a shaft which cannot be penetrated faster than two feet per hour (fifteen minute minimum) using a rock auger with bullet-shaped hardened steel teeth (Kennametal bits or equivalent), and the drilling equipment should have the capacity to produce a continuous torque of at least 1,000,000 inch pounds and a downward force of at least 50,000 pounds (a Xxxxxx LLDH in good working condition) for piers up to seventy two inches in diameter. Use of equipment with greater torque or downward force modifies the definition of refusal to be the point at which the equipment cannot penetrate faster than two feet per hour (fifteen minute minimum). In rare cases, refusal may occur on a rock seam or boulder above the general massive rock surface. The compensation for Caisson Rock should include only material that cannot be penetrated by the rock auger at the specified rate.
Asset Management Supplier will: i) maintain an asset inventory of all media and equipment where Accenture Data is stored. Access to such media and equipment will be restricted to authorized Personnel; ii) classify Accenture Data so that it is properly identified and access to it is appropriately restricted; iii) maintain an acceptable use policy with restrictions on printing Accenture Data and procedures for appropriately disposing of printed materials that contain Accenture Data when such data is no longer needed under the Agreement; iv) maintain an appropriate approval process whereby Supplier’s approval is required prior to its Personnel storing Accenture Data on portable devices, remotely accessing Accenture Data, or processing such data outside of Supplier facilities. If remote access is approved, Personnel will use multi-factor authentication, which may include the use of smart cards with certificates, One Time Password (OTP) tokens, and biometrics.
FIPPA The HSP acknowledges that the LHIN is bound by FIPPA and that any information provided to the LHIN in connection with this Agreement may be subject to disclosure in accordance with FIPPA.
Millwright Xxxxx be to assist and work under the direction and instructions I or A. He will work alone at times performing assignments in keeping with his training. During the course of his year, training must become proficient in good practices in the areas of fitting, aligning, lubricating and the operation of all shop tools and machines. In addition to the foregoing, he will be exposed to and the process of learning techniques required in trouble shooting key production machinery, pipe fitting, basic welding and machining but not be expected to display a high degree of proficiency in these areas at this point. Millwright Must be capable of performing the tasks of fittings, aligning, lubricating an able to operate all shop tools and machines. Must under direction become proficient in basic welding and pipe fitting as well as dismantling and reassembly of plant equipment. Under direction,will continueto develop skills in trouble shooting all plant equipment and improve his skills at machining part and be exposed to basic principles of hydraulics and pneumatic. He may work alone frequently, but occasionally will require direction and instructions form Millwright I or A. Millwright 11: be capable, without direction of fitting, aligning and lubrication and taking apart and reassembling plant equipment. In addition, is expected to be able to weld, operate shop tools and do pipe fitting as required. Must under direction, become proficient at effective methods of trouble shooting and repairing hydraulic, pneumatic and mechanical faults in plant machinery. I: Must be capable without direction of performing all practices under Xxxxxxxxxx Must under directionbecomeproficient at reading and understanding blueprints, all phases of installing new equipment, laying out hydraulic and mechanical drives and meet speed and power requirements correctly. Xxxxxxxxxx "A": Must he capable without direction, of performing all under Xxxxxxxxxx X, and Must take full responsibility for work done by himself or his assistant. Must he in possession of a Millwright Certificate or a Machinist Certificate or Welder Certificate. Millwrightspresently employed in this classification will not be required to have a Certificate.
HOSPITALITY Purchaser is to provide the location , name and address of the closest significant children’s entertainment complex and/or educational facility.
New Hampshire In the event You do not receive satisfaction under this Agreement, You may contact the New Hampshire Insurance Department, 00 Xxxxx Xxxxx Xxxxxx, Xxxxxxx, XX 00000, (000) 000-0000. ARBITRATION section of this Agreement is removed.
Car Rental 6.1 Vendors that must travel may rent a car at their destination when it is less expensive than other transportation such as taxis, airport shuttles or public transportation such as buses or subways.
Per-pupil Funding The School's non-facility general fund per-pupil funding shall be as defined in Sec. 302D-28, HRS. The Commission shall distribute the School's per-pupil allocation each fiscal year pursuant to Sec. 302D-28(f), HRS, and shall provide the School with the calculations used to determine the per-pupil amount each year. All funds distributed to the School from the Commission shall be used solely for the School's educational purposes as appropriated by the Legislature, and the School shall have discretion to determine how such funding shall be allocated at the school level to serve those purposes subject to applicable laws and this Contract.
Arkansas CANCELLATION section is amended as follows: A ten percent (10%) penalty per month shall be applied to refunds not paid or credited within forty-five (45) days of receipt of returned Service Agreement.
Shoes All uniformed staff shall be provided with 2 pairs of shoes annually, replaceable on a normal wear and tear basis.
