Xxxxxxx Block Assemblies Sample Clauses

Xxxxxxx Block Assemblies a. The Contractor only installs SKF, FAG and Timken xxxxxxx blocks. The Contractor ensures that the xxxxxxx block supplier is from the accredited OEM agent or directly from the OEM. b. Bearing lubricant is SKF LGEP 2 or equivalent FAG, Timken recommended lubricant. CONTRACT 46 ECC3 COVER PAGES x. Xxxxxxx block seals are designed for outdoor service in the presence of fine abrasive dust and moisture and are of the grease charged horizontal mechanical labyrinth type. “Taconite” type heavy –duty labyrinth seals, incorporating internal V-ring seal, with primary axial labyrinth passages arranged axially are used. Grease will be supplied via a grease nipple situated on the non-rotating part of the seal. Rotating labyrinth seal to have positive locking to prevent rotational movement relative to shaft. “Taconite” seal design to incorporate mechanical locking mechanism which prevents relative movement between stationary “Taconite” seal ring and housing during operation. Solid section O-ring seals to be used between the rotating “Taconite” and the shafts to prevent moisture ingress. Solid section O-rings to be used between the stationary “Taconite” seal and the housing to prevent moisture ingress between the mating surfaces. d. The shaft is supported on C3 radial internal clearance spherical roller bearings with tapered bore mounted on adapter sleeves, adequately chosen to accommodate static, dynamic and any anticipated end thrust loading. On designs where the end thrust loading is deemed to be zero, a nominal value is included to allow for any misalignment. e. The L10 bearing life shall in all cases be checked to ensure a life of at least 100 000 hours at full load. f. Care is taken to ensure that the correct limits are chosen for shafts and housings to suit a particular bearing. g. Only local standard stock sizes are used and special bearings avoided. Housing dimensions are in accordance with ISO 113-2. h. Bearing housings are fitted with blanking plates where the shafts do not project. i. Bearing sets are located in accordance with the requirements of the assembly. x. Xxxxxxx blocks are installed such that the cap bolts shall not be subjected to any tensile forces. Xxxxxxx blocks shall also be mounted on adjustable sole plates. k. All adjustment set screws are galvanized and are so designed as to make full contact with the xxxxxxx block base. On no account shall the set screw be allowed to contact a sloping face of the xxxxxxx block housing. Two (2) adjustment sc...
AutoNDA by SimpleDocs

Related to Xxxxxxx Block Assemblies

  • DNS name server availability Refers to the ability of a public-­‐DNS registered “IP address” of a particular name server listed as authoritative for a domain name, to answer DNS queries from an Internet user. All the public DNS-­‐registered “IP address” of all name servers of the domain name being monitored shall be tested individually. If 51% or more of the DNS testing probes get undefined/unanswered results from “DNS tests” to a name server “IP address” during a given time, the name server “IP address” will be considered unavailable.

  • Xxxxxxx, Esq If to the Executive, to him at the offices of the Company with a copy to him at his home address, set forth in the records of the Company. Any person named above may designate another address or fax number by giving notice in accordance with this Section to the other persons named above.

  • Xxxxxxxx Tobacco Co [Xxxxx Progeny] Circuit Court, Levy County, (Bronson, FL) $8 million in compensatory damages; 90% of fault assigned to RJR Tobacco, which reduced the award to $7.2 million; $72 million in punitive damages. See “— Xxxxx and Xxxxx Progeny Cases” below.

  • Start-Up and Synchronization Consistent with the mutually acceptable procedures of the Developer and Connecting Transmission Owner, the Developer is responsible for the proper synchronization of the Large Generating Facility to the New York State Transmission System in accordance with NYISO and Connecting Transmission Owner procedures and requirements.

  • Loop Provisioning Involving Integrated Digital Loop Carriers 2.6.1 Where Xxxx has requested an Unbundled Loop and BellSouth uses IDLC systems to provide the local service to the End User and BellSouth has a suitable alternate facility available, BellSouth will make such alternative facilities available to Xxxx. If a suitable alternative facility is not available, then to the extent it is technically feasible, BellSouth will implement one of the following alternative arrangements for Xxxx (e.g. hairpinning): 1. Roll the circuit(s) from the IDLC to any spare copper that exists to the customer premises. 2. Roll the circuit(s) from the IDLC to an existing DLC that is not integrated. 3. If capacity exists, provide "side-door" porting through the switch. 4. If capacity exists, provide "Digital Access Cross Connect System (DACS)- door" porting (if the IDLC routes through a DACS prior to integration into the switch). 2.6.2 Arrangements 3 and 4 above require the use of a designed circuit. Therefore, non- designed Loops such as the SL1 voice grade and UCL-ND may not be ordered in these cases. 2.6.3 If no alternate facility is available, and upon request from Xxxx, and if agreed to by both Parties, BellSouth may utilize its Special Construction (SC) process to determine the additional costs required to provision facilities. Xxxx will then have the option of paying the one-time SC rates to place the Loop.

  • Xxxxxx, Esq Anyone to whom a notice may be given under this Agreement may designate a new address by notice to that effect given to the other party in accordance with this subsection (b). Each such notice shall be deemed given upon the receipt thereof when delivered in person and on the second business day after the mailing when sent by mail as aforesaid. (c) You understand that, upon exercise of this Option, you may recognize income for tax purposes in an amount equal to the excess of the then fair market value of the Shares purchased over the Option Price for such Shares. Your employer may withhold tax from your current compensation with respect to such income or any other income which it deems you to have received in connection therewith; to the extent that your then current compensation is insufficient to satisfy the withholding tax liability, you will be required to make a cash payment to cover such liability as a condition of exercise of this Option. (d) If this Option shall be mutilated, lost, stolen or destroyed, the Company shall issue in exchange and substitution for and upon cancellation of the mutilated Option, or in lieu of and in substitution for the Option lost, stolen or destroyed, a new Option of like tenor and denomination, but only upon receipt of evidence satisfactory to the Company of such loss, theft or destruction of such Option and such indemnity and, if requested by the Company, such bond, as shall in each case be satisfactory to the Company. You must also comply with such other reasonable requirements and pay such other reasonable charges as the Company may prescribe in connection with such issuance. (e) This Option shall be governed and construed in accordance with the substantive laws of the State of New York applicable to contracts executed, delivered and to be fully performed in the State of New York, without giving effect to contrary provisions regarding conflict of laws. (f) This Agreement shall inure to the benefit of and shall be binding upon your heirs, executors, administrators and legal representatives, and shall inure to the benefit of and be binding upon the Company and its successors and assigns. You may not assign, transfer, pledge, encumber, hypothecate or otherwise dispose of this Agreement, or any of your rights hereunder except if and to the extent expressly permitted by Section 8 of this Agreement, and any such attempted prohibited delegation or disposition shall be null and void and without effect. (g) This Agreement constitutes the complete understanding between the parties with respect to the subject matter hereof, and no statement, representation, warranty or covenant has been made by either party with respect thereto except as expressly set forth herein. This Agreement shall not be altered, modified, amended or terminated except by written instrument signed by each of the parties hereto. (h) This Agreement may be executed in any number of counterparts, each of which shall be deemed an original but all of which shall constitute one and the same instrument. (i) The section headings contained herein are for the purposes of convenience only, are not intended to define or limit the contents of said sections and are not part of this Agreement. (j) By signing below, you hereby accept this Option subject to all of the terms and provisions hereof and acknowledge all of the representations, warranties and agreements set forth above. This Option shall not be effective until you have signed this Option and delivered it to the Company.

  • SHOP XXXXXXX The Shop Xxxxxxx shall be a County employee as selected by the Union. A list of shop stewards will be kept current and sent by the Union to each department head and to Human Resources. Duties required by the Union of its stewards, except attendance at meetings with the County, supervisory personnel and aggrieved employees arising out of a grievance already initiated by an employee under Article 14 hereof, shall not interfere with their or other employees, regular work assignments as employees of the County. The shop xxxxxxx, or their designee, involved with a particular grievance must be identified at Step 1 of the grievance procedure and will be designated as the only bargaining unit employee who will be able to gather information pertaining to that particular grievance. The Union will make reasonable efforts to control the amount of investigative time spent between the shop xxxxxxx and the aggrieved employee. Meetings scheduled with management and other proper investigative procedures, and attendance at meetings specified in Steps 1 and 2 of the grievance procedure shall be considered hours worked for compensation purposes to the extent such meetings occur during the normal hours of work, and not otherwise. In order to use union leave for this purpose, Shop Stewards must notify the supervisor/department head of meetings and other commitments at the time these are scheduled. Attendance at meetings specified in Step 3 of the grievance procedure shall be considered hours worked during regularly scheduled business hours of the County for the xxxxxxx involved, witnesses and the grievant. The County shall not be liable for any overtime as a result of the meeting. Witnesses and the shop xxxxxxx involved shall be granted leave with pay to the extent their presence at the proceedings is required. If it is a discharge case the grievant shall not be paid except as provided in a remedy awarded.

  • Xxxxxxx, P E. will perform as the Consultant’s principal for this Project. As principal on this Project, this person shall be the primary contact with the Utilities Director, Utilities Engineer, or another person so designated, and shall have authority to bind the Consultant. So long as the individual named above remains actively employed or retained by the Consultant, he/she shall perform the function of principal on this Project.

  • Check Meters Developer, at its option and expense, may install and operate, on its premises and on its side of the Point of Interconnection, one or more check meters to check Connecting Transmission Owner’s meters. Such check meters shall be for check purposes only and shall not be used for the measurement of power flows for purposes of this Agreement, except as provided in Article 7.4 below. The check meters shall be subject at all reasonable times to inspection and examination by Connecting Transmission Owner or its designee. The installation, operation and maintenance thereof shall be performed entirely by Developer in accordance with Good Utility Practice.

  • Minimum Customer Support Requirements for TIPS Sales Vendor shall provide timely and commercially reasonable support for TIPS Sales or as agreed to in the applicable Supplemental Agreement.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!