Capacity Tolerance definition

Capacity Tolerance has the meaning as specified in Section A of Part I (Individual Terms);
Capacity Tolerance. [specify as a percentage the tolerance of the Capacity within which the Facility
Capacity Tolerance. [specify as a percentage the tolerance of the Capacity within which the Facility is deemed fully Commissioned] „Tolerancja Mocy”: [proszę określić w procentach wielkość akceptowanej różnicy w stosunku do Mocy, w granicach której Instalacja jest uznana za w pełni Uruchomioną] Physical address of Site: [specify] Geograficzny adres Lokalizacji: [proszę określić]

Examples of Capacity Tolerance in a sentence

  • NGG will keep the Reservation Party regularly notified of any such changes to the Reserved Capacity Tolerance.

  • Dimensional analysis was conducted for critical dimensions of the DASH 6® NRFit Syringe device family and its accessories (with NRFit connectors), in accordance with the criteria in ISO 80369-6.Device Verification Testing for the piston syringe was conducted in accordance with ISO 7886-1 (Capacity Tolerance, Leakage Testing Side Force, Leakage Testing Axial Force).


More Definitions of Capacity Tolerance

Capacity Tolerance means five (5) percent (%) tolerance of the Capacity, in excess or in reduction, within which the Facility is deemed to have achieved the full Commissioning.
Capacity Tolerance. [specify as a percentage] Physical address of Site: [specify] "Delivery Point": [specify] Location of Metering Device: [specify] "Network Operator": [specify] "Transmission System Operator": [specify where the Network Operator is not a transmission system operator] "Metering Entity": [specify] "Relevant Codes and Rules": [specify use of system agreements, grid codes and ancillary documentation to be entered into] 4. DISPOSICIONES GENERALES E INSTALACIONES “Periodo de Entrega” de la electricidad: [ ] cada mes natural; o [ ]______________[especificar] "Periodo de Entrega" de los Certificados: [especificar, sujeto a las Reglas de Emisión y Registro] “Instalación”: [especificar] Tipo de generación de la instalación: [especificar] “Capacidad”: [especificar] “Flexibilidad de Capacidad”: [especificar como porcentaje] Dirección Física del Emplazamiento: [especificar] "Punto de Entrega": [especificar] Ubicación del Aparato de Medición: [especificar] "Operador de Red": [especificar] "Operador del Sistema de Transmisión": [especificar si el Operador de Red no es un operador de la red de transmisión] “Entidad de Medición": [especificar] “Códigos y Normas Relevantes" [especificar el uso de acuerdos del sistema, códigos de red y documentación auxiliar que haya que suscribir] If "Provisions of this Agreement on Balancing Services" are specified to apply Section B of in Part I (Individual Terms): Si se especifican las "Disposiciones de este Contrato sobre Servicios de Equilibrio", se aplicará la Sección B de la Parte I (Disposiciones Particulares):
Capacity Tolerance has the meaning as specified in Section A of Part I (Individual Terms); „Tolerancja Mocy” ma znaczenie określone w Rozdziale A Części I (Warunki Indywidualne),

Related to Capacity Tolerance

  • Tolerance means a state of adaptation in which exposure to a drug induces changes that result in a diminution of one or more of the drug’s effects over time.

  • Zero tolerance means that the school will not tolerate the possession of any weapon by any person. The term “weapon” is defined as any object or substance which by its design, threatened use, or use could cause bodily injury or property damage, including any object which could reasonably be mistaken for a weapon. The division director and dean of student life shall use their discretion when interpreting the use and intent of such articles at school.

  • Load means energy consumed by Customers together with allocated losses and unaccounted for energy;

  • Process weight means the total weight of all materials introduced into any source operation. Solid fuels charged will be considered as part of the process weight, but liquid and gaseous fuels and combustion air will not.

  • voltage means the root-mean-square value of electrical potential between two conductors.

  • Potential electrical output capacity means, with regard to a unit, 33 per- cent of the maximum design heat input of the unit.

  • Working pressure means the settled pressure of a compressed gas at a reference temperature of 15 °C in a full pressure receptacle;

  • medium voltage means the set of nominal voltage levels that lie above low voltage and below high voltage in the range of 1 kV < Un 44 kV. [SANS 1019]

  • Payload means all property to be flown or used on or in a Launch Vehicle.

  • Workload means a special education teacher’s total number of minutes required for all due process responsibilities, including direct and indirect services, evaluation and reevaluation time, management of individualized education programs (IEPs), travel time, parental contact, and other services required in the IEPs.

  • Density means the permitted number of dwelling units per

  • Flocculation means a process to enhance agglomeration or collection of smaller floc particles into larger, more easily settleable particles through gentle stirring by hydraulic or mechanical means.

  • Pressure means relative pressure versus atmospheric pressure, unless otherwise stated.

  • Transponder means an access device used to gain entry to the parking facility;

  • Service Specification means and include detailed description, statements to technical data, performance characteristics, and standards (Indian as well as) as applicable and as specified in the Contract as well as those specifications relating to Industry standards and codes applicable to the performance of the work, work performance quality and the specifications affecting the works or any additional specification required to be produced by the DCO to meet the design criteria.

  • Process Gas means gas used for which alternate fuels, other than another gaseous fuel, are not technically feasible such as in applications requiring precise temperature controls and precise flame characteristics.

  • Configuration means State-specific changes made to the Software without Source Code or structural data model changes occurring.

  • Anaerobic digester means a liquid manure storage area that is constructed with the intent to capture and combust gas emissions resulting from the digestion of waste by microbes in anaerobic conditions. An anaerobic digester is a LMSA and is required to comply with all requirements applicable to LMSAs. Requirements specific to anaerobic digesters will be noted when applicable.

  • Acceptance Testing mean the tests, reviews and other activities that are performed by or on behalf of Agency to determine whether the Deliverables meet the Acceptance Criteria or otherwise satisfy the Agency, as determined by the Agency in its sole discretion.

  • technical specification means a document that prescribes technical requirements to be fulfilled by a product, process or service;

  • Generator Forced Outage means an immediate reduction in output or capacity or removal from service, in whole or in part, of a generating unit by reason of an Emergency or threatened Emergency, unanticipated failure, or other cause beyond the control of the owner or operator of the facility, as specified in the relevant portions of the PJM Manuals. A reduction in output or removal from service of a generating unit in response to changes in market conditions shall not constitute a Generator Forced Outage.

  • Interruptible Capacity means capacity that may be interrupted by the Operator at any time in order to fulfil shippers’ nominations under a firm capacity reservation.

  • Grab sample means an individual sample collected in less than 15 minutes in conjunction with an instantaneous flow measurement.

  • Project Capacity means the AC capacity of the project at the generating terminal(s) and to be contracted with MSEDCL for supply from the Solar Power Project.

  • Spacecraft (9) means active and passive satellites and space probes.

  • Operating pressure means the pressure at which the parts of an irrigation system are designed by the manufacturer to operate.