Protection degree definition

Protection degree means the protection provided by a barrier/enclosure related to the contact with live parts by a test probe, such as a test finger (IPXXB) or a test wire (IPXXD), as defined in Annex 3.
Sample 1Sample 2Sample 3
Protection degree means Protection provided by a barrier/enclosure related to the contact with live parts by a test probe, such as a test finger (IPXXB), or a test wire (IPXXD),
Sample 1Sample 2Sample 3
Protection degree means the protection provided by a barrier or enclosure related to the contact with live parts by a test probe, such as a jointed test finger (IPXXB) or a test wire access probe (IPXXD);
Sample 1Sample 2Sample 3

Examples of Protection degree in a sentence

  • In case of outdoor installation a minimum IP54 Ingress Protection degree shall be used.

  • Protection degree IPXXD is an International Electrotechnical Commission (IEC) specification for protection from direct contact of high voltage sources.

  • Protection degree IP20 Electrostatic discharges IEC 1000-4-2 /3 Noise IEC 1000-4-3 /3Bursts IEC 1000-4-4 /4Stocking temperature -10 / +70°CWorking temperature +5 / +40°C*Relative humidity 90% without condensationAltitude 1000 m above sea levelInstallation position Vertical +/- 15°*The MFC - MFD module can supply nominal values of braking current up to 50 °C inside the panel; above this temperature performance degrades by 2% for every 1 °C rise.

  • Ms. Tham holds a Bachelor of Chemical Engineering with Environmental Protection degree from Loughborough University, UK.

  • Protection degree IPXXB is an IEC specification for protection from direct contact of high voltage sources.

  • The judgments in WABQ disclose some divergence of opinion as to how this issue is to be resolved.

  • Standard: IEC 947-2 category B Board Enclosure:a) sheet steel Construction not less than 2mm thickness with electro-static and thermal painting.b) Sleeves type connection for all cables.c) Cable glands suitable for incoming and outgoing cables.d) Protection degree is to be IP55.f) Double door.

  • Standard : IEC 947-2 category B Board Enclosure:a) sheet steel Construction not less than 2mm thickness with electro-static and thermal painting.b) Sleeves type connection for all cables.c) Cable glands suitable for incoming and outgoing cables.d) Protection degree is to be IP55.f) Double door.

  • The offered boxes has the following characteristics Protection degree: IP 43 as per IEC 60529. Shock resistance: IK 10 as per IEC 62262. Dielectric rigidity: 6 kV as per IEC 60950, transversal resistance of our material. Fire resistance: UL 94 V0. Acid resistance: no reaction while exposed to acids where in some cases the acid might escape from the batteries and affect some plastic materials (polyester) that turn grey or black.

  • Bounced checks can be collected quite effectively by collectors complying with this important consumer protection law.


More Definitions of Protection degree

Protection degree means the Protection provided by a barrier/enclosure related to the contact with live parts by a test probe, such as a test finger (IPXXB) as defined in Appendix 1 of Annex 9.
Sample 1Sample 2
Protection degree means the protection provided by a barrier/enclosure related to the contact with live parts by a test probe, such as a test finger (IPXXB) or a test wire (IPXXD), as defined in Annex 3. [2.28 "REESS of different types” means systems which do not differ significantly in such essential aspects as:
Sample 1
Protection degree means protection provided by a barrier / enclosure related to the contact with live parts by a test probe, such as a test finger (IPXXB) or a test wire (IPXXD). 3.36 “Degree of protection” means the extent of protection provided by an enclosure against access to hazardous parts against ingress of solid foreign objects and / or against ingress of water and verified by standardized test methods. 3.37 “Barrier” means the part providing protection against direct contact to the live parts from any direction of access. 3.38 “Direct contact” means contact of persons with the live parts. 3.39 “Live parts” means the conductive part(s) intended to be electrically energized in normal use. 3.40 “Indirect contact” means contact of persons or livestock with exposed conductive parts. 3.41 “Solid insulator” means the insulating coating of wiring harness provided in order to cover and protect the live parts against direct contact from any direction of access, covers for insulating the live parts of connectors, and varnish or paint for the purpose of insulation. 3.42 “Enclosure” means the part enclosing the internal units and providing protection against direct contact from any direction of access. 3.43 “Active driving possible mode” is the vehicle mode when application of pressure to the accelerator pedal (or activation of an equivalent control) or release of the brake system causes the electric power train to move the vehicle. 3.44 “Automatic disconnect” is a device that, when triggered, conductively separates the electrical energy sources from the rest of high voltage circuit of the electrical power train. 3.45 “Service disconnect” means the device for deactivation of the electrical circuit when conducting checks and services of the REESS, fuel cell stack, etc. 3.46 “State of Charge (SOC)” means the available electrical charge in a tested- device expressed as a percentage of its rated capacity. 3.47 “Maximum Net power” means the power obtained at the wheels of electric vehicle when tested on chassis dynamometer or at motor shaft when measured at bench dynamometer at corresponding vehicle / motor speed at reference atmospheric conditions and full load on wheels of vehicle/motor.
Sample 1

Related to Protection degree

  • Degree means a course of study in a higher education institution leading to a degree as described in the Australian Qualifications Framework as at 1 January 1995.

  • Physical Safeguards are physical measures, policies, and procedures to protect CONTRACTOR’s electronic information systems and related buildings and equipment, from natural and environmental hazards, and unauthorized intrusion.

  • Direct scattered radiation means that scattered radiation which has been deviated in direction only by materials irradiated by the useful beam (See "Scattered radiation").

  • Event Outside Our Control means any act or event beyond WRAS’s reasonable control, including without limitation strikes, lock-outs or other industrial action by third parties, civil commotion, riot, invasion, terrorist attack or threat of terrorist attack, war (whether declared or not) or threat or preparation for war, fire, explosion, storm, flood, earthquake, subsidence, epidemic or other natural disaster, or failure of public or private telecommunications networks [or impossibility of the use of railways, shipping, aircraft, motor transport or other means of public or private transport;

  • Sewage sludge weight means the weight of sewage sludge, in dry U.S. tons, including admixtures such as liming materials or bulking agents. Monitoring frequencies for sewage sludge parameters are based on the reported sludge weight generated in a calendar year (use the most recent calendar year data when the NPDES permit is up for renewal).

  • Safeguarding means measures or controls that are prescribed to protect information systems.

  • Affordable means, a sales price or rent level that is within the means of a low- or moderate- income household as defined within N.J.A.C. 5:93-7.4, and, in the case of an ownership unit, that the sales price for the unit conforms to the standards set forth in N.J.A.C. 5:80-26.6, as may be amended and supplemented, and, in the case of a rental unit, that the rent for the unit conforms to the standards set forth in N.J.A.C. 5:80-26.12, as may be amended and supplemented.

  • Cathodic protection tester means a person who can demonstrate an understanding of the principles and measurements of all common types of cathodic protection systems as applied to buried or submerged metal piping and tank systems. At a minimum, such persons must have education and experience in soil resistivity, stray current, structure-to-soil potential, and component electrical isolation measurements of buried metal piping and tank systems.