Assumption for thermal characterization and simulation Sample Clauses

Assumption for thermal characterization and simulation. Information presented by the module vendor in relation to this document should be obtained from a 'confined or ducted flow' described as: • A wind tunnel is defined in Figure 8-1 • The multiple module configurations are defined in Table 8-1 • Test environment is shown in Table 8-2 Other assumptions: • PCB host board should have no copper layer. • Duct housing is made of plastic. • Dimensions of the chassis should allow maximum 4 modules on 86.0 mm spacing. Setup: ▪ Fans should be arranged across the vent opening so that the direction of airflow is side to side (length axis) and be of constant volume airflow. ▪ Airflow should be characterized using a calibrated hot wire anemometer placed at the airflow inlet. ▪ Thermocouples should be used to measure the case temperatures ▪ Case temperature measurement point will vary by module vendor and PMD type. Module vendors should identify the information to the end user for verification in the system level environment. ▪ A steady state should be obtained at measurements. ▪ Combination of the different power class module or different sizes of heat sink are not assumed for this characterization. ▪ During thermal evaluation, CFP modules should handle the specified data patterns (TBD) on both the XLAUI/CAUI and PMD outputs. ▪ Other measurement data provided is at the discretion of the module manufacturer. • An example of simulated and measurement data is shown in Figure 8-2. Port 1 Port 2 Port 3 Port 4 Blower (Out Flow) Table 8-1: Wind Tunnel Dimensions & Module Position13,14,15 Case Heat Sink Type Heat Sink Dimensions Wind Tunnel Dimensions Port 1 Port 2 Port 3 Port 4 Height Depth Length (Width) Height Depth Length 1 No Riding Heat Sink N/A N/A N/A 16.6 190 644 CFP 1 CFP 2 CFP 3 CFP 4 2 25.4mm Total Conformal 11.8 103 81 28.4 190 644 CFP 1 - CFP 2 - 3 35mm Total Conformal 21.4 103 81 38 190 644 CFP 1 - CFP 2 - 4 25.4mm Total & 105mm width 11.8 103 105 28.4 190 644 CFP 1 - - CFP 2 5 35mm Total & 210mm depth 21.4 185 81 38 260 644 CFP 1 - CFP 2 -
Sample 1
AutoNDA by SimpleDocs

Related to Assumption for thermal characterization and simulation

  • DESCRIPTION OF CONTRACT MODIFICATION This contract modification is made in accordance with Exhibit E-Revised-1, Contractual Terms and Conditions, Section 22. CHANGES, to be made part hereof for all pertinent purposes. The changes are as follows:

  • ESTIMATED / SPECIFIC QUANTITY CONTRACTS Estimated quantity contracts, also referred to as indefinite delivery / indefinite quantity contracts, are expressly agreed and understood to be made for only the quantities, if any, actually ordered during the Contract term. No guarantee of any quantity is implied or given. With respect to any specific quantity stated in the contract, the Commissioner reserves the right after award to order up to 20% more or less (rounded to the next highest whole number) than the specific quantities called for in the Contract. Notwithstanding the foregoing, the Commissioner may purchase greater or lesser percentages of Contract quantities should the Commissioner and Contractor so agree. Such agreement may include an equitable price adjustment.

  • Meter Testing Company shall provide at least twenty-four (24) hours' notice to Seller prior to any test it may perform on the revenue meters or metering equipment. Seller shall have the right to have a representative present during each such test. Seller may request, and Company shall perform, if requested, tests in addition to the every fifth-year test and Seller shall pay the cost of such tests. Company may, in its sole discretion, perform tests in addition to the fifth year test and Company shall pay the cost of such tests. If any of the revenue meters or metering equipment is found to be inaccurate at any time, as determined by testing in accordance with this Section 10.2 (Meter Testing), Company shall promptly cause such equipment to be made accurate, and the period of inaccuracy, as well as an estimate for correct meter readings, shall be determined in accordance with Section 10.3 (Corrections).

  • Escrow Format Specification Deposit’s Format. Registry objects, such as domains, contacts, name servers, registrars, etc. will be compiled into a file constructed as described in draft-xxxxx-xxxxxxx-registry-data-escrow, see Part A, Section 9, reference 1 of this Specification and draft-xxxxx-xxxxxxx-dnrd-objects-mapping, see Part A, Section 9, reference 2 of this Specification (collectively, the “DNDE Specification”). The DNDE Specification describes some elements as optional; Registry Operator will include those elements in the Deposits if they are available. If not already an RFC, Registry Operator will use the most recent draft version of the DNDE Specification available at the Effective Date. Registry Operator may at its election use newer versions of the DNDE Specification after the Effective Date. Once the DNDE Specification is published as an RFC, Registry Operator will implement that version of the DNDE Specification, no later than one hundred eighty (180) calendar days after. UTF-8 character encoding will be used.

  • Contract Formation Subject to FAR Sections 1.601(a) and 43.102, the Government Order must be signed by a duly warranted contracting officer, in writing. The same requirement applies to contract modifications affecting the rights of the parties. All terms and conditions intended to bind the Government must be included within the contract signed by the Government.

  • DISTRIBUTION OF CONTRACTOR PRICE LIST AND CONTRACT APPENDICES Contractor shall provide Authorized Users with electronic copies of the Contract, including price lists and Appendices, upon request. Contract Updates will be handled as provided in Appendix C – Contract Modification Procedures.

  • LIMITATIONS ON REVERSE ENGINEERING, DECOMPILATION AND DISASSEMBLY You may not reverse engineer, decompile, or disassemble the Software, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation.

  • Review of Agreement Each party acknowledges that it has had time to review this agreement and, as desired, consult with counsel. In the interpretation of this agreement, no adverse presumption shall be made against any party on the basis that it has prepared, or participated in the preparation of, this agreement.

  • Contract Forms This Section contains forms which, once completed, will form part of the Contract. The forms for Performance Security and Advance Payment Security, when required, shall only be completed by the successful tenderer after contract award.

  • Optional Xactimate Response Attachment (Part 2)

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!