Compliance with Safety Standards and Premises Regulations Sample Clauses

Compliance with Safety Standards and Premises Regulations. This Section shall only apply if Seller will provide some or all of the Services on property owned or leased by Harvard. a. OSHA State and Local Regulation. Seller shall ensure that all of its personnel, subcontractors, members of the Harvard community, and the general public are properly protected from potential injury due to any act or omission, or any machinery, equipment or other property owned or operated, by Seller or any of its employees, agents, representatives, suppliers, subcontractors or others for whose conduct Seller may be responsible, as required by the Occupational Safety and Health Act of 1970, and all applicable regulations thereunder, and by all other Laws. Seller shall ensure that all machinery and equipment used in the performance of the work comply with applicable law. If Harvard, in its reasonable judgment, determines that any additional protection is necessary to comply with good management practices or applicable law, Seller shall provide the same at no additional charge. Seller shall be considered to have materially breached this Purchase Order if any safety and health standards or regulations have been breached by the Seller. b. Lockout/Tagout. In accordance with the Occupational Safety and Health Administration's Lockout/Tagout standard (29 CFR 1910.147), Seller(s) involved in operations related to equipment or machinery lockout that affect Harvard's employees must submit their Energy Control Procedures to Harvard and train affected employees of Harvard prior to the xxxx Xxxxxx agrees to the Purchase Order. The cost of training will be the responsibility of Seller. Seller shall also comply with Harvard’s Lockout/Tagout policy and procedures.
Sample 1
AutoNDA by SimpleDocs

Related to Compliance with Safety Standards and Premises Regulations

  • Contract Work Hours and Safety Standards Act The following clauses apply to any Federal-aid construction contract in an amount in excess of $100,000 and subject to the overtime provisions of the Contract Work Hours and Safety Standards Act. These clauses shall be inserted in addition to the clauses required by 29 CFR 5.5(a) or 29 CFR 4.6. As used in this paragraph, the terms laborers and mechanics include watchmen and guards.

  • COMPLIANCE WITH HEALTH, SAFETY, AND ENVIRONMENTAL REGULATIONS The Contractor, it’s Subcontractors, and their respective employees, shall comply fully with all applicable federal, state, and local health, safety, and environmental laws, ordinances, rules and regulations in the performance of the services, including but not limited to those promulgated by the City and by the Occupational Safety and Health Administration (OSHA). In case of conflict, the most stringent safety requirement shall govern. The Contractor shall indemnify and hold the City harmless from and against all claims, demands, suits, actions, judgments, fines, penalties and liability of every kind arising from the breach of the Contractor’s obligations under this paragraph.

  • Compliance with Applicable Laws, Rules and Regulations The Dealer Manager represents to the Company that (a) it is a member of FINRA in good standing, and (b) it and its employees and representatives who will perform services hereunder have all required licenses and registrations to act under this Agreement. With respect to its participation and the participation by each Participating Dealer in the offer and sale of the Offered Shares (including, without limitation, any resales and transfers of Offered Shares), the Dealer Manager agrees, and, by virtue of entering into the Participating Dealer Agreement, each Participating Dealer shall have agreed, to comply with any applicable requirements of the Securities Act and the Exchange Act, applicable state securities or blue sky laws, and, specifically including, but not in any way limited to, NASD Conduct Rules 2340 and 2420, and FINRA Conduct Rules 2310, 5130 and 5141.

  • Compliance with Accessibility Standards All parties to this Agreement shall ensure that the plans for and the construction of all projects subject to this Agreement are in compliance with standards issued or approved by the Texas Department of Licensing and Regulation (TDLR) as meeting or consistent with minimum accessibility requirements of the Americans with Disabilities Act (P.L. 101-336) (ADA).

  • Compliance with Rules and Regulations PFPC undertakes to comply with all applicable requirements of the Securities Laws and any laws, rules and regulations of governmental authorities having jurisdiction with respect to the duties to be performed by PFPC hereunder. Except as specifically set forth herein, PFPC assumes no responsibility for such compliance by the Fund or any other entity.

  • CONTRACT WORK HOURS AND SAFETY STANDARDS As per the Contract Work Hours and Safety Standards Act (40 U.S.C. 3701-3708), where applicable, all Customer Purchase Orders in excess of ,000 that involve the employment of mechanics or laborers must include a provision for compliance with 40 U.S.C. 3702 and 3704, as supplemented by Department of Labor regulations (29 CFR Part 5). Under 40 U.S.C. 3702 of the Act, each contractor must be required to compute the wages of every mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work week is permissible provided that the worker is compensated at a rate of not less than one and a half times the basic rate of pay for all hours worked in excess of 40 hours in the work week. The requirements of 40 U.S.C. 3704 are applicable to construction work and provide that no laborer or mechanic must be required to work in surroundings or under working conditions which are unsanitary, hazardous or dangerous. These requirements do not apply to the purchases of supplies or materials or articles ordinarily available on the open market, or contracts for transportation or transmission of intelligence.

  • Compliance with Laws, Rules and Regulations a. Assurances. The Contractor agrees that all activity pursuant to this Contract will be in accordance with all applicable current federal, state and local laws, rules, and regulations, including but not limited to the Public Records Act (chapter 42.56 RCW), the Freedom of Information Act (5 U.S.C. 522) and the Records Retention Act (chapter 40.14 RCW).

  • Compliance with Standards Although the standards for workmanship, material, and equipment have been selected in these specifications as a basis of reference, standards and specifications of the other bank member countries and recommendations of standards international organizations will be acceptable provided they are substantially equivalent to the designated standards and provided furthermore that the contractor submits for approval detailed specifications which he proposes to use. Reference to brand names or catalog numbers if any in these specifications have been made only for that equipment for which it has been determined that a degree of standardization is necessary to maintain certain essential features. And in certain cases such references have also been made for purposes of convenience to specify the requirements, in either case offers of alternative goods, which have similar characteristics and provide performance and quality at lease equal to those specified are acceptable. If the contractor offers materials, equipment, design calculations or tests, which conform to standards other than those specified, full details of the differences between the proposed standards and that specified in so far as they affect the design or purpose of the equipment, are to be supplied by the contractor if called upon to do so by the engineer, where required by the engineer for approval purposes, the contractor shall supply, without charge, duplicate copies of the proposed standards with English translations of the relevant portions. The contractor shall have available in his place of business (or in his supplier’s works) the relevant copies of standards or codes used for the use of the Engineer.

  • Compliance with Regulations The contractor (hereinafter includes consultants) will comply with the Acts and the Regulations relative to Non-discrimination in Federally-assisted programs of the U.S. Department of Transportation, Federal Highway Administration, as they may be amended from time to time, which are herein incorporated by reference and made a part of this contract.

  • Compliance with Governmental Regulations Landlord and Tenant shall comply with all rules, regulations and requirements promulgated by national, state or local governmental agencies or utility suppliers concerning the use of utility services, including any rationing, limitation or other control. Tenant shall not be entitled to terminate this Lease nor to any abatement in rent by reason of such compliance.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!