Classification Definitions Note: The following classification definitions should be read in conjunction with: • the stream and field definitions in subclause 1.4.3 and 1.4.75 respectively: • the definitions of “or equivalent”, “work within the scope of this level” and “Engineering Associate” at the end of this Schedule; • the National Metal and Engineering Competency Standards Implementation Guide especially Table 2 of that Guide which shows the alignment between old and new titles under the Australian Qualifications Framework. For example Advanced Certificates are now known as National Diplomas and Associate Diplomas as National Advanced Diplomas; • Clause 5.1.3 (f) Points. Trainer/Supervisor/Coordinator - Level 1 A Trainer/Supervisor/Coordinator - Level I is an employee who is responsible for the work of other employees and/or provision of structured on-the-job training. Such an employee has completed a qualification at AQFIII level or above, of which at least one third of the competencies are related to supervision/training, or equivalent. Notwithstanding the above definition an employee who is mainly engaged to perform work supervising or coordinating the work of other employees and who has sufficient additional training beyond that of those coordinated or supervised so as to enable the employee to perform work within the scope of this level shall be classified at this level. Trainer/Supervisor/Coordinator - Level II A Trainer/Supervisor/Coordinator - Level II is an employee who is responsible for the supervision and/or training of Trainers/Supervisors/Coordinators - Level I. Such an employee has completed an AQF IV or V qualification or equivalent of which at least 50% of the competencies are in supervision/training. WAGE GROUP: C14 Engineering/Production Employee - Level I As Engineering/Production Employee - Level I is an employee who is undertaking up to 38 hours induction training which may include information on the enterprise, conditions of employment, introduction to supervisors and fellow workers, training and career path opportunities, plant layout, work and documentation procedures, occupational health and safety, equal employment opportunity and quality control/assurance. An employee at this level performs routine duties essentially of a manual nature and to the level of his/her training:
– SCOPE & DEFINITIONS 2.01 The employer recognizes the Ontario Nurses’ Association as the sole and exclusive bargaining agent for all registered nurses and nurses with a temporary certificate of registration employed by THE WILLOWGROVE LTC Residence in the City of Xxxxxxxx, save and except managers, persons above the rank of manager and persons covered by a subsisting collective agreement.
020 Definitions The following definitions shall be applicable to this chapter:
Specific Definitions The following terms used in this Agreement shall have the following meanings:
PROJECT DEFINITIONS The following capitalized terms have the meanings assigned below for purposes of Exhibits A and B.
SECTION I - DEFINITIONS As used in this Agreement, the following terms shall have the meanings ascribed herein unless otherwise stated or reasonably required by the Agreement, and other forms of any defined words shall have a meaning parallel thereto.
000 DEFINITIONS 6.100 Maintenance shall be work performed for the repair, renovation, revamp and upkeep of property, machinery and equipment within the limits of the plant property.
DEFINITIONS AND INTERPRETATION Definitions 1.1 In this Contract, unless the contrary intention appears: Activity End Date means the date reported as such in a Student Statistical Report for an individual's enrolment in an individual subject. Activity Start Date means the date reported as such in a Student Statistical Report for an individual's enrolment in an individual subject. Apprentice has the meaning given to it in the Act. Approved Training Scheme means a training scheme approved under section 5.5.2 of the Act. Brokering Services means the recruitment of individuals to participate in Skills First subsidised training in exchange for payment from the Training Provider or the student. It excludes activities carried out by individuals who are employees of the Training Provider on the Training Provider’s payroll, whose role includes the identification and recruitment of potential students. Business Day means a day which is not a Saturday, Sunday or a public holiday in Melbourne, Victoria.
050 Definitions 3.48.060 Filing of FEPC and EEOC complaints not prohibited. 3.48.070 Informal and formal procedures. 3.48.080 Costs of hearing. 3.48.090 Representation. 3.48.100 Freedom from reprisal.
Purpose and Definitions 1. The purpose of this Chapter is to promote the objectives of this Agreement by simplifying customs procedures in relation to bilateral trade between the Parties.
