ETV test procedures Sample Clauses

ETV test procedures. For highway engines, the FTP is described in 40 CFR Part 86, and the SET is specified in 40 CFR 86.1360. The FTP is a transient test cycle and the SET is a 13­ mode steady-state test cycle. For SCR on a highway diesel engine, the minimum ETV testing at a single test point consists of one FTP cold start cycle, three FTP hot start cycles, and one SET. The weighted cold start results will be applied to each of the weighted hot start results to provide three transient sets of data for each regulated pollutant and BSFC. Additional testing at each test point may be required to detect the expected emissions reduction, as described in Section 5.1.2. The test parameters will be derived from the baseline engine mapping procedure. For nonroad engines, the FTP is described in 40 CFR Part 89. Nonroad engines will be verified with both the applicable steady-state cycle and the nonroad transient cycle as published in the Federal Register. For SCR on a nonroad diesel engine, the minimum ETV test at a single test point consists of triplicate multimode FTP tests. Additional testing at each test point may be required to detect the expected emissions reduction, as described in Section 5.1.2. The test parameters will be derived from the baseline engine mapping procedure. Stationary engines will generally follow the same ETV test procedure as similar nonroad engines. For SCR on a stationary diesel engine, the minimum ETV test at a single test point consists of triplicate multimode FTP tests. Additional testing at each test point may be required to detect the expected emissions reduction, as described in Section 5.1.2. The test parameters will be derived from the baseline engine mapping procedure. Unless otherwise described in this document or identified in the approved test/QA plan, the FTP is to be followed in its entirety. In accordance with this protocol, any deviations from the test/QA plan will be noted and throughly documented by the testing organization in its report. Existing data of any kind and chassis or in-use field (e.g., on-road testing systems) data are not acceptable as the basis for ETV verification.
Sample 1Sample 2
AutoNDA by SimpleDocs

Related to ETV test procedures

  • Test procedures For an Asset Review, the Asset Representations Reviewer will perform for each Asset Review Receivable the procedures listed under “Procedures to be Performed” in Schedule A for each representation and warranty (each, a “Test”), using the Asset Review Materials listed for each such Test in Schedule A. For each Test and Asset Review Receivable, the Asset Representations Reviewer will determine if the Test has been satisfied (a “Test Pass”) or if the Test has not been satisfied (a “Test Fail”).

  • Test procedure The engine speed shall be gradually increased from idle to the target engine speed, not exceeding the tolerance band of ±3 per cent of the target engine speed, and held constant. Then the throttle control shall be rapidly released and the engine speed shall be returned to idle. The sound pressure level shall be measured during a period of operation consisting of a maintaining constant engine speed of 1 second and throughout the entire deceleration period. The maximum sound level meter reading during this period of operation, mathematically rounded to the first decimal place, is taken as the test value.

  • MOVE-OUT PROCEDURES Upon termination of this Lease Contract for any reason, Resident shall surrender possession of the Premises in the same condition as when received, in a good, clean and sanitary condition, including removing all trash from the Premises and returning furniture to its original placement. Owner shall note the condition of the Premises, including all appliances, furnishings and fixtures therein, and any damage done thereto which is deemed by Owner to have occurred during Resident’s occupancy and use of the Premises. Resident shall pay all utility and service bills to the Premises for which Resident is responsible and cancel all utility accounts in the name of the Resident. Resident shall return to Owner all keys, access cards, and remote control devices, if applicable, issued to the Resident by Owner. If all keys, cards, and devices issued to Resident are not returned to Owner, Resident shall pay all costs associated with re-keying and replacement of locks, keys, cards, and remote devices for the Premises. Resident’s failure to follow the prescribed move-out procedures may result in the partial or full application of the Deposit to cover these charges, but in no event shall such application be construed as liquidated damages. If no Deposit exists, Resident will be charged for all damages, cleaning, repairs, re-keying, and replacement costs, which will be due within 30 days of such billing. In the event Resident moves out prior to the end of the Lease Term, Resident shall be responsible for either the Reletting Fee or the Assignment Fee, in addition to continuing liability for Rent through the end of the Lease Term until a suitable replacement resident is identified.

  • Procurement procedures 11.1 The Recipient must secure the best value for money and shall act in a fair, open and non-discriminatory manner in all purchases of goods and services.

  • Drug Testing Procedures a. The testing procedures and safeguards provided in this policy shall be adhered to by any laboratory personnel administering departmental drug tests.

  • RECOVERY PROCEDURES The nature and severity of any disaster will influence the recovery procedures. One crucial factor in determining how BellSouth will proceed with restoration is whether or not BellSouth's equipment is incapacitated. Regardless of who's equipment is out of service, BellSouth will move as quickly as possible to aid with service recovery; however, the approach that will be taken may differ depending upon the location of the problem.

  • Payment Procedures Upon receipt of a Right Certificate representing exercisable Rights, with the form of election to purchase and certification duly executed, accompanied by payment of the aggregate Purchase Price for the total number of one one-hundredths of a Preferred Share to be purchased and an amount equal to any applicable transfer tax required to be paid by the holder of such Right Certificate in accordance with Section 9, in cash or by certified or cashier's check or money order payable to the order of the Company, the Rights Agent shall thereupon promptly (i)(A) requisition from any transfer agent of the Preferred Shares (or make available, if the Rights Agent is the transfer agent) certificates for the number of Preferred Shares to be purchased and the Company hereby irrevocably authorizes its transfer agent to comply with all such requests, or (B) if the Company shall have elected to deposit the total number of Preferred Shares issuable upon exercise of the Rights hereunder with a depository agent, requisition from the depositary agent depositary receipts representing interests in such number of one one-hundredths of a Preferred Share as are to be purchased (in which case certificates for the Preferred Shares represented by such receipts shall be deposited by the transfer agent with the depositary agent) and the Company hereby directs the depositary agent to comply with all such requests, (ii) when appropriate, requisition from the Company the amount of cash to be paid in lieu of the issuance of fractional shares in accordance with Section 14 or otherwise in accordance with Section 11.1.3, (iii) promptly after receipt of such certificates or depositary receipts, cause the same to be delivered to or upon the order of the registered holder of such Right Certificate, registered in such name or names as may be designated by such holder and (iv) when appropriate, after receipt, promptly deliver such cash to or upon the order of the registered holder of such Right Certificate. In the event that the Company is obligated to issue other securities of the Company, pay cash and/or distribute other property pursuant to Section 11.1.3, the Company will make all arrangements necessary so that such other securities, cash and/or other property are available for distribution by the Rights Agent, if and when appropriate.

  • AML/KYC Procedures “AML/KYC Procedures” means the customer due diligence (CDD) procedures of a Reporting Financial Institution pursuant to the anti-money laundering or similar requirements of the jurisdiction concerned to which such Reporting Financial Institution is subject.

  • Subcontract Procedures Without relieving it of, or in any way limiting, its obligations to NYSERDA under this Agreement, the Contractor may enter into Subcontracts for the performance of Work or for the purchase of materials or equipment. Prior to beginning any Work, Contractor shall notify the NYSERDA Project Manager of all subcontractors performing work under the Agreement, as well as all changes in subcontractors throughout the term of the Agreement. Except for a subcontractor or supplier specified in a team arrangement with the Contractor in the Contractor’s original proposal, and except for any subcontract or order for equipment, supplies or materials from a single subcontractor or supplier totaling less than $50,000, the Contractor shall select all subcontractors or suppliers through a process of competitive bidding or multi-source price review. A team arrangement is one where a subcontractor or supplier specified in the Contractor’s proposal is performing a substantial portion of the Work and is making a substantial contribution to the management and/or design of the Project. In the event that a competitive bidding or multi-source price review is not feasible, the Contractor shall document an explanation for, and justification of, a sole source selection. The Contractor shall document the process by which a subcontractor or supplier is selected by making a record summarizing the nature and scope of the work, equipment, supplies or materials sought, the name of each person or organization submitting, or requested to submit, a bid or proposal, the price or fee bid, and the basis for selection of the subcontractor or supplier. An explanation for, and justification of, a sole source selection must identify why the work, equipment, supplies or materials involved are obtainable from or require a subcontractor with unique or exceptionally scarce qualifications or experience, specialized equipment, or facilities not readily available from other sources, or patents, copyrights, or proprietary data. All Subcontracts shall contain provisions comparable to those set forth in this Agreement applicable to a subcontractor or supplier, and those set forth in Exhibit C to the extent required by law, and all other provisions now or hereafter required by law to be contained therein. Each Subcontract shall make express reference to this Agreement, and shall state that in the event of any conflict or inconsistency between any Subcontract and this Agreement, the terms and conditions of this Agreement shall control as between Subcontractor and Contractor. For each Subcontract valued at $100,000 or more, the Contractor shall obtain and maintain, pursuant to Section 4.05, a completed Vendor Assurance of No Conflict of Interest or Detrimental Effect form from such Subcontractor prior to the execution of the Subcontract. Such form shall be made available to the Contractor by NYSERDA. Each such Subcontract shall contain a provision whereby the Subcontractor warrants and guarantees that there is and shall be no actual or potential conflict of interest that could prevent the Subcontractor’s satisfactory or ethical performance of duties required to be performed pursuant to the terms of the Subcontract and that the Subcontractor shall have a duty to notify NYSERDA immediately of any actual or potential conflicts of interest. If this Agreement includes a provision requiring Contractor to make Payments to NYSERDA for the Sale or Licensing of a Product, each Subcontract shall include the provisions of Section 8.02, suitably modified to identify the parties. The Contractor shall submit to NYSERDA’s Contract Administrator for review and written approval any subcontract(s) specified in the Statement of Work as requiring NYSERDA approval, including any replacements thereof.

  • WARRANTY PROCEDURES You need proof of purchase for warranty service.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!