FIRE ALARM BRACKETS AND TRAFFIC SIGNS Sample Clauses

FIRE ALARM BRACKETS AND TRAFFIC SIGNS. Item 6 (a) Remove and install fire alarm type bracket or transfer a fire alarm type bracket and associated luminaire. Item 6 (a) 1 install fire alarm bracket Item 6(b) Furnish fire alarm type bracket as per drawing H-3860. The Contractor shall furnish all labor, material and equipment necessary to replace or transfer a fire alarm bracket and the associated fire alarm luminaire. Replacement brackets are to be furnished by the Contractor under appropriate item. Contractor will furnish replacement lamps, fire alarm luminaires and ballast (where necessary).
Sample 1Sample 2Sample 3
AutoNDA by SimpleDocs
FIRE ALARM BRACKETS AND TRAFFIC SIGNS. Item 6 (a) - Remove and install fire alarm type bracket or transfer a fire alarm type bracket and associated luminaire. Item 6 (a)1 - Install fire alarm bracket. Item 6 (b) - Furnish fire alarm type bracket as per DWG No. H-3860. The Contractor shall furnish all labor, material and equipment necessary to replace or transfer a fire alarm bracket and the associated fire alarm luminaire. Replacement brackets are to be furnished by NYCDOT. The Contractor will furnish replacement lamps, fire alarm luminaires and ballast (where necessary). Replacement fire alarm brackets shall be installed as follows: Wood pole shall be drilled so that the distance from the sidewalk to the bottom of the pole plate will be eighteen (18') feet for a fire alarm bracket. Further details to be in accordance with DWG No. H-3860. On any metal post, where necessary, drill hole in shaft to serve as wire way, remove all sharp edges to avoid injury to insulation of wires. Attach bracket to post with fasteners approved for this particular installation. The Contractor shall furnish fasteners. Wiring and fusing for the fire alarm luminaire shall be part of the item and shall be in accordance with DWG No. J-5135. Item 6 (c) - Remove and install or transfer a non-illuminated traffic sign. Signs, other than those of the Division of Traffic, shall be removed, stored by the Contractor, and the proper agency notified. Division of Traffic Operations signs are to be reinstalled by use of stainless steel banding furnished by the Contractor. Payment: The transfer of street name signs shall be on the basis of one Item 6 (c) per lamppost. All other Division of Traffic Operations signs shall be on the basis of one Item 6 (c) for each set of bands necessary to support signs.
Sample 1Sample 2Sample 3

Related to FIRE ALARM BRACKETS AND TRAFFIC SIGNS

  • Traffic Signals Based upon the results of the Traffic Warrant Studies, the Engineer shall identify and prepare Traffic Signal Plans for all warranted traffic signals. The Engineer shall confirm the power source for all signals and coordinate with the appropriate utility agency. Traffic Signal Plans must be signed and sealed by a Texas Registered Professional Engineer. The Engineer shall develop all quantities, general notes, specifications and incorporate the appropriate agency standards required to complete construction. Traffic signal poles, fixtures, signs, and lighting must be designed per the Green Ribbon Report recommendations and standards. The Engineer shall provide the following information in the Traffic Signal Plans:

  • Trunk Group Architecture and Traffic Routing The Parties shall jointly engineer and configure Local/IntraLATA Trunks over the physical Interconnection arrangements as follows:

  • Workstation/Laptop encryption All workstations and laptops that process and/or store DHCS PHI or PI must be encrypted using a FIPS 140-2 certified algorithm which is 128bit or higher, such as Advanced Encryption Standard (AES). The encryption solution must be full disk unless approved by the DHCS Information Security Office.

  • Export and Retrieval by Customer During the Subscription Term and subject to the Agreement, Customer can access its Personal Data at any time. Customer may export and retrieve its Personal Data in a standard format. Export and retrieval may be subject to technical limitations, in which case SAP and Customer will find a reasonable method to allow Customer access to Personal Data.

  • Fire, Life Safety, and Accessibility Codes The following codes, in the versions approved by the Georgia State Fire Marshal/Fire Safety Commissioner and Department of Human Resources, shall be used. The Design Professional will designate any additional codes or special modifications in the Supplementary General Conditions.

  • Secure Information Handling and Transfers 7.1 Physical and electronic handling, processing and transferring of DWP Data, including secure access to systems and the use of encryption where appropriate.

  • Malicious Use of Orphan Glue Records Registry Operator shall take action to remove orphan glue records (as defined at xxxx://xxx.xxxxx.xxx/en/committees/security/sac048.pdf) when provided with evidence in written form that such records are present in connection with malicious conduct.

  • Contractor Certification regarding Business with Certain Countries and Organizations Pursuant to Subchapter F, Chapter 2252, Texas Government Code], Contractor certifies Contractor is not engaged in business with Iran, Sudan, or a foreign terrorist organization. Contractor acknowledges this Agreement may be terminated and payment withheld if this certification is inaccurate.

  • Open and Transparent Consistent with ICANN’s expressed mission and core values, ICANN shall operate in an open and transparent manner.

  • Fire Safety 9.5.1 Residents found in violation of the following fire safety stipulations not only put themselves at risk but also jeopardizes the safety of the entire community.

Time is Money Join Law Insider Premium to draft better contracts faster.