Gas characteristics Sample Clauses

Gas characteristics. The biogas must meet the requirements of the Biomass Ordinance (Biomasseverordnung) in the currently applicable version. The Supplier must be able to prove the biogenic properties of the biogas by means of mass balance tracking in the XXXX biogas register or by means of the delivery model extract (Liefermodell- Auszug) there. In the case of biogas produced outside of the Federal Republic of Germany, the Supplier must present a record of the posting of the mass balance system and confirm the mass balance of the biogas quantities through an independent audit.
Sample 1
AutoNDA by SimpleDocs
Gas characteristics. (a) The Gas characteristics including, without limiting the generality of the foregoing, Gross Heating Value, relative density, nitrogen and carbon dioxide content of the Gas shall be determined by continuous recording equipment or by laboratory equipment.
Sample 1
Gas characteristics. TABLE 2.1-1 GAS CHARACTERISTICS ---------------------------------------------------------------------------------------- 1. Pipeline Inlet Pressure at Transco, Minimum, psig 530 ---------------------------------------------------------------------------------------- 2. Pipeline Inlet Pressure at Transco, Maximum, psig 850 ---------------------------------------------------------------------------------------- 3. Pipeline Inlet Temperature at Transco, Maximum, OF. 120 ---------------------------------------------------------------------------------------- 4. Pipeline Inlet Temperature at Transco, Normal, OF. 80 ---------------------------------------------------------------------------------------- 5. Gas Gravity (Air = 1.0) 0.59 ---------------------------------------------------------------------------------------- 6. Molar Composition, % N2 0.32 CO2 0.99 C1 95.07 C 2 2.47 C3 0.64 iC4 0.17 nC4 0.15 nC5 0.06 C6+ 0.04 0.09 ---------------------------------------------------------------------------------------- 7. Water Content, lbs./MMScf { 7 ---------------------------------------------------------------------------------------- 8. Sulfur Content (as hydrogen sulfide), grain/100 Scf { 0.3 ---------------------------------------------------------------------------------------- Gross Heating Value, Btu/Scf 1,040 +/- 60 ---------------------------------------------------------------------------------------- -------------------------------------------------------------------------------- TENASKA GEORGIA PARTNERS, L.P. Appendix A - Scope System Description & Design Basis ---------------------- Attachment I Page 5 of 6 -------------------------------------------------------------------------------- NATURAL GAS PIPELINE Date: 9/3/99 --------------------------------------------------------------------------------
Sample 1

Related to Gas characteristics

  • Characteristics The Initial Contracts have the following characteristics: (i) all the Contracts are secured by Motorcycles; (ii) no Initial Contract has a remaining maturity of more than 84 months; and (iii) the final scheduled payment on the Initial Contract with the latest maturity is due not later than June 2014. Approximately 77.89% of the Principal Balance of the Initial Contracts as of the Initial Cutoff Date is attributable to loans for purchases of new Motorcycles and approximately 22.11% is attributable to loans for purchases of used Motorcycles. No Initial Contract was originated after the Initial Cutoff Date. No Initial Contract has a Contract Rate less than 3.989%. The last scheduled payment date of the Contracts (including any Subsequent Contracts) is due not later than September 2014. Approximately 98.98% of the Principal Balance of the Initial Contracts as of the Initial Cutoff Date is attributable to loans to purchase Motorcycles manufactured by Harley-Davidson or Buell and approximately 1.02% of the Principal Balance of the Initial Contracts as of the Initial Cutoff Date is attributable to loans to purchase Motorcycles not manufactured by Harley-Davidson or Buell.

  • Mortgage Loan Characteristics The characteristics of the related Mortgage Loan Package are as set forth on the description of the pool characteristics for the applicable Mortgage Loan Package delivered pursuant to Section 11 on the related Closing Date in the form attached as Exhibit B to each related Assignment and Conveyance Agreement;

  • Individual Characteristics Each Receivable has the following individual characteristics as of the Cut-Off Date:

  • Characteristics of Receivables As of the Cut-Off Date (or such other date as may be specifically set forth below), each Receivable:

  • Quality All products will be new and unused. All products provided by the Contractor must meet all federal, state, and local standards for quality and safety requirements. Products not meeting the requirements of this section will be deemed unacceptable and returned to the Contractor for credit at no charge to the State.

  • Concentrations No Receivable has a Statistical Contract Value (when combined with the Statistical Contract Value of any other Receivable with the same or an Affiliated Obligor) that exceeds 1% of the aggregate Statistical Contract Value of all the Receivables.

  • Configuration The configuration for the Purchase Right Aircraft will be the Detail Specification for Model 767-3S2F aircraft at the revision level in effect at the time of the Supplemental Agreement. Such Detail Specification will be revised to include (i) changes required to obtain required regulatory certificates and (ii) other changes as mutually agreed upon by Boeing and Customer.

  • Calculations Respecting Mortgage Loans Calculations required to be made pursuant to this Agreement with respect to any Mortgage Loan in the Trust Fund shall be made based upon current information as to the terms of the Mortgage Loans and reports of payments received from the Mortgagor on such Mortgage Loans and payments to be made to the Securities Administrator as supplied to the Securities Administrator by the Master Servicer. The Securities Administrator shall not be required to recompute, verify or recalculate the information supplied to it by the Master Servicer or any Servicer.

Time is Money Join Law Insider Premium to draft better contracts faster.