New Parts, Including Modification and/or Replacement Parts. Each new part exported to the United States with a DGAC airworthiness approval will have a JAA Form One, Authorised Release Certificate. The FAA shall accept a DGAC Authorised Release Certificate on a new part, including a modification and/or replacement part, for the products and appliances identified in Section II, only when the DGAC certifies, by the issuance of the JAA Form One, that each part: (1) Is eligible for installation in a product or appliance which has been granted an FAA design approval; (2) Conforms to FAA- approved design data and is safe for installation; (3) Is marked in accordance with paragraph 3.2.3.0(a) of these Implementation 3.2.1.5
New Parts, Including Modification and/or Replacement Parts. All parts exported to the United States with LBA airworthiness approval will have a 3.2.1.5
New Parts, Including Modification and/or Replacement Parts. All parts exported to Germany with FAA airworthiness approval will have an FAA Form 8130-3, JAA Form One. The FAA shall accept a LBA Authorised Release Certificate on a new part, including a modification and/or replacement part, for the products and appliances identified in Section II, only when the LBA certifies, by the issuance of the JAA Form One, that each part:
New Parts, Including Modification and/or Replacement Parts. Each new part exported to France with an FAA airworthiness approval will have an FAA Form 8130-3, Airworthiness Approval Tag. The DGAC shall accept an FAA airworthiness approval tag on a new part, including a modification and/or replacement part, for the products and appliances identified in Section II, only when the FAA certifies, by the issuance of FAA Form 8130-3, that each part: (1) Is eligible for installation in a product or appliance which has been granted an DGAC design approval; (2) Conforms to design data approved under a: (i) DGAC Type Certificate; (ii) DGAC STC; (iii) DGAC JTSO/QAC Authorisation; or (iv) DGAC approved aircraft
New Parts, Including Modification and/or Replacement Parts. (a) The DCA shall accept the airworthiness approval tag of the FAA for new parts, including modification and/or replacements parts, that have been produced by a U.S. production approval holder (i.e., under U.S. Type Certificate, Production Certificate, Technical Standard Order Authorization, or a Parts Manufacturer Approval).
(b) Each part exported to Malaysia will have an FAA Form 8130-3,
New Parts, Including Modification and/or Replacement Parts. All parts exported to the United States with ENAC airworthiness approval will have a JAA Form One. The FAA shall accept an ENAC Authorised Release Certificate on a new part, including a modification and/or replacement part, for the products and appliances identified in Section II, only when ENAC certifies, by the issuance of the JAA Form One, that each part: (1) Is eligible for installation in a product or appliance which has been granted an FAA design approval.
New Parts, Including Modification and/or Replacement Parts. All parts exported to Italy with FAA airworthiness approval will have an FAA Form 8130-3, Airworthiness Approval Tag. ENAC shall accept an FAA airworthiness approval tag on a new part, including a modification and/or replacement part, for the products and appliances identified in Section II, only when the FAA certifies, by the issuance of the FAA Form 8130-3, that each part: (1) Is eligible for installation in a product or appliance which has been granted an ENAC design approval; (2) Conforms to design data approved under an: (i) ENAC Type Certificate (ii) ENAC STC (iii) ENAC JTSO Authorisation, or (iv) ENAC approved aircraft modification; (3) Is marked in accordance with paragraph 3.2.3.1
(a) of these Implementation Procedures; and (4) Meets all additional requirements prescribed by the ENAC, as notified. (In particular, refer to paragraph 3.0.4.1 for PMA requirements.)
New Parts, Including Modification and/or Replacement Parts. All parts exported to the Netherlands with FAA airworthiness approval will have an FAA Form 8130-3, Airworthiness Approval Tag. The CAA-NL shall accept an FAA airworthiness approval tag on a new part, including a modification and/or replacement part, for the products and appliances identified in Section II, only when the FAA certifies, by the issuance of the FAA Form 8130-3, that each part: (1) Is eligible for installation in a product or appliance which has been granted a CAA-NL design approval; (2) Conforms to design data approved under a: (i) CAA-NL Type Certificate (ii) CAA-NL STC (iii) CAA-NL JTSO Authorisation, or (iv) CAA-NL approved aircraft modification;
New Parts, Including Modification and/or Replacement Parts. All parts exported to the United States with UKCAA airworthiness approval will have a JAA Form One. The FAA shall accept a UKCAA Authorized Release Certificate on a new part, including a modification and/or replacement part, for the products and appliances identified in Section II, only when the UKCAA certifies, 3.
New Parts, Including Modification and/or Replacement Parts. All parts exported to the United Kingdom with FAA airworthiness approval will have an FAA Form 8130-3, Airworthiness Approval Tag. The UKCAA shall accept an FAA airworthiness approval tag on a new part, including a modification and/or replacement part, for the products and appliances identified in Section II, only when the by the issuance of the JAA Form One, that each part: FAA certifies, by the issuance of the FAA Form 8130-3, that each part:
(1) Is eligible for installation in a product or appliance which has been granted an FAA design approval.
(2) Conforms to FAA- approved design data and is safe for installation; (3) Is marked in accordance with paragraph 3.2.3.0(a) of these Implementation Procedures; and (4) Meets all additional requirements prescribed by the FAA, as notified.
(1) Is eligible for installation in a product or appliance which has been granted a UKCAA design approval; (2) Conforms to design data approved under a: (i) UKCAA Type Certificate (ii) UKCAA STC (iii) UKCAA JTSO Authorization, or (iv) UKCAA approved modification; (3) Is marked in accordance with paragraph 3.2.3.1
(a) of these Implementation Procedures; and (4) Meets all additional requirements prescribed by the UKCAA, as notified. In particular, refer to paragraph 3.0.4.1 for PMA requirements.
