Non-Recommended Configurations Sample Clauses

Non-Recommended Configurations. Customer Equipment that does not meet HTC’s minimum technical or other specifications constitutes a “Non-Recommended Configuration.” NEITHER HTC NOR ANY OF ITS AFFILIATES, SUPPLIERS OR AGENTS WARRANT THAT A NON-RECOMMENDED CONFIGURATION WILL ENABLE YOU TO SUCCESSFULLY INSTALL, ACCESS, OPERATE, OR USE THE SERVICES. YOU ACKNOWLEDGE THAT ANY SUCH INSTALLATION, ACCESS, OPERATION, OR USE COULD CAUSE CUSTOMER EQUIPMENT TO FAIL TO OPERATE OR CAUSE DAMAGE TO CUSTOMER EQUIPMENT, YOU, YOUR PREMISES OR HTC EQUIPMENT. NEITHER HTC NOR ANY OF ITS AFFILIATES, SUPPLIERS OR AGENTS SHALL HAVE ANY LIABILITY WHATSOEVER FOR ANY SUCH FAILURE OR DAMAGE. HTC reserves the right to deny you customer support for the Services and/or terminate Service(s) if you use a Non-Recommended Configuration.
Sample 1Sample 2Sample 3
AutoNDA by SimpleDocs
Non-Recommended Configurations. Customer Equipment that does not meet Packerland's minimum technical or other specifications constitutes a "Non- Recommended Configuration." Neither Packerland nor any of its affiliates, suppliers or agents warrant that a non-recommended configuration will enable you to successfully install, access, operate or use the services. You acknowledge that any such installation, access, operation, or use could cause customer equipment to fail to operate or cause damage to customer equipment, you, your premises or Packerland Equipment. Neither Packerland nor any of its affiliates, suppliers or agents shall have any liability whatsoever for any such failure or damage. Packerland reserves the right to deny you customer support for the Services and/or terminate Service(s) if you use a Non-Recommended Configuration.
Sample 1
Non-Recommended Configurations. If you install or use Customer Equipment that does not meet the minimum technical or other specifications described above (a "Non-Recommended Configuration"), you agree (i) that the Services or some features of the Services may degrade or fail, (ii) that you will not be entitled to customer support relating to any issues other than the quality of the signal delivered to the MTA, and (iii) that the following limitation of liability shall apply: NEITHER COMCAST NOR ANY OF ITS AFFILIATES OR AGENTS WARRANT THAT A NON- RECOMMENDED CONFIGURATION WILL ENABLE YOU TO SUCCESSFULLY INSTALL, ACCESS, OPERATE, OR USE THE SERVICES. YOU ACKNOWLEDGE THAT ANY SUCH INSTALLATION, ACCESS, OPERATION, OR USE COULD CAUSE DAMAGE TO CUSTOMER EQUIPMENT. NEITHER COMCAST NOR ANY OF ITS ASSOCIATED PARTIES SHALL HAVE ANY LIABILITY WHATSOEVER FOR ANY SUCH FAILURE OR DAMAGE. The foregoing limitation of liability is in addition to and shall not limit any other limitation of liability set forth in this Agreement.
Sample 1
Non-Recommended Configurations. If you install or use in connection with the Digital Phone services Customer Equipment or an Internet connection that does not meet the minimum technical or other requirements described in Section 2.b.ii above (a "Non-Recommended Configuration"), you agree (i) that you will not be entitled to customer support relating to any issues other than the quality of the signal delivered to the MTA, and (ii) that the following limitation of liability shall apply: NEITHER ANTIETAM NOR ANY OF ITS OWNERS, OFFICERS, DIRECTORS, EMPLOYEES, PARENT COMPANY, AFFILIATES, OR AGENTS (COLLECTIVELY, “ANTIETAM PARTIES”), WARRANT THAT A NON-RECOMMENDED CONFIGURATION WILL ENABLE YOU TO SUCCESSFULLY INSTALL, ACCESS, OPERATE, OR USE THE DIGITAL PHONE XXXXXXXX.XXX ACKNOWLEDGE THAT ANY SUCH INSTALLATION, ACCESS, OPERATION, OR USE COULD CAUSE DAMAGE TO CUSTOMER EQUIPMENT. NONE OF THE ANTIETAM PARTIES SHALL HAVE ANY LIABILITY WHATSOEVER FOR ANY SUCH FAILURE OR DAMAGE, INCLUDING LACK OF 911/E911, INCOMPATIBILITY WITH ALARM OR HOME SECURITY SYSTEMS, MEDICAL MONITORING DEVICES, FAX EQUIPMENT OR DIAL-UP MODEMS. For purposes of this Agreement, "affiliate” means any entity that controls, is controlled by, or is under common control with Antietam. The foregoing limitation of liability is in addition to and shall not limit any other limitation of liability set forth in this Agreement.
Sample 1

Related to Non-Recommended Configurations

  • Implementation Specifications 1. The accounting shall contain the date, nature, and purpose of such disclosures, and the name and address of the person or agency to whom the disclosure is made.

  • Effect of Addenda, Bulletins, and Change Orders No special implication, interpretation, construction, connotation, denotation, import, or meaning shall be assigned to any provision of the Contract Documents because of changes created by the issuance of any (1) Addendum, (2) Bulletin, or (3) Change Order other than the precise meaning that the Contract Documents would have had if the provision thus created had read originally as it reads subsequent to the (1) Addendum, (2) Bulletin, or (3) Change Order by which it was created.

  • Classification Specifications The Employer agrees to supply the President of the Union or his/her designate with the classification specifications for those classifications in the Bargaining Unit.

  • 253 Design Change (a) “Design Change” is a change in work and/or materials shown in the Schedule of Items and described in Plans or specifications that has been mutually agreed to in writing or ordered by Contracting Officer. Changes of a minor nature (such as adjustment in horizontal and vertical alignment, that do not exceed specified tolerance, necessary to maintain or balance earthwork quantities substantially as designed) and variation in quantities, as described in B5.251, shall not be considered Design Changes.

  • Schematic Design Documents In accordance with the approved Preliminary Design and Construction Schedule and based upon approval of and comments made by the Owner regarding the Concept Design Studies, the Design Professional shall prepare and submit to the Owner Schematic Design Documents, including drawings and outline specifications. These documents shall represent a further development of the approved design concept, providing additional detail and specificity regarding the intended design solution. Typically, all such documents shall be drawn to scale, indicating materials and assemblies, as appropriate, to convey the design intent and to illustrate the Project’s basic elements, scale and relationship to the Site. All major pieces of furniture and equipment to be fixed or supplied by the CM/GC shall be illustrated to scale. (See ASTM Standard Practice E 1804-02, August 2007, Sections 6.3, 8.2 and 8.3 for guidance on information which is generally developed in Schematic Design.)

  • DAF Specifications Developer shall submit initial specifications for the DAF, including System Protection Facilities, to Connecting Transmission Owner and NYISO at least one hundred eighty (180) Calendar Days prior to the Initial Synchronization Date; and final specifications for review and comment at least ninety (90) Calendar Days prior to the Initial Synchronization Date. Connecting Transmission Owner and NYISO shall review such specifications to ensure that the DAF are compatible with the technical specifications, operational control, and safety requirements of the Connecting Transmission Owner and NYISO and comment on such specifications within thirty (30) Calendar Days of Developer’s submission. All specifications provided hereunder shall be deemed to be Confidential Information.

  • Design Changes Axon may make design changes to any Axon Device or Service without notifying Agency or making the same change to Axon Devices and Services previously purchased by Agency.

  • CHANGE IN CLASSIFICATION SPECIFICATIONS Section 1. The Employer shall notify the Union of intended classification studies.

  • Manufacturer's Recommendations All work or materials shall be installed in accordance with the manufacturer's recommendations and requirements. The Contractor shall obtain the manufacturer’s recommendations and requirements, for its use at the Site in executing the Work, copies of bulletins, circulars, catalogues, or other publications bearing the manufacturer’s titles, numbers, editions, dates, etc. If the manufacturer’s recommendations and requirements are not available, the Contractor shall request installation instructions from the Design Professional.

  • Alternative Work Schedule An alternate forty (40) hour work schedule (other than five (5) uniform and consecutive eight (8) hour days in a seven (7) day period), or for hospital personnel an eighty (80) hour workweek in a fourteen (14) day period and other mutually agreed upon schedules that comply with applicable federal and state law. Employee work schedules normally include two (2) consecutive days off.

Time is Money Join Law Insider Premium to draft better contracts faster.