PLACEMENT TOLERANCES. .1 Place riprap bedding within a tolerance of +50 mm of the specified thickness and within a tolerance of +100 mm of the specified elevation.
PLACEMENT TOLERANCES Sample Clauses
Related to PLACEMENT TOLERANCES
ROAD TOLERANCES Purchaser shall perform road work within the tolerances listed below. The tolerance class for each road is listed on the TYPICAL SECTION SHEET. Tolerance Class A B C Road and Subgrade Width (feet) +1.5 +1.5 +2.0 Subgrade Elevation (feet +/-) 0.5 1.0 2.0 Centerline alignment (feet lt./rt.) 1.0 1.5 3.0 1-6 ORDER OF PRECEDENCE Any conflict or inconsistency in the road plan will be resolved by giving the documents precedence in the following order:
Tolerances 1. If a non-originating material used in the production of a product does not satisfy the requirements set out in Annex 3-B, the product shall be considered as originating in a Party, provided that:
Placement of DNS probes Probes for measuring DNS parameters shall be placed as near as possible to the DNS resolvers on the networks with the most users across the different geographic regions; care shall be taken not to deploy probes behind high propagation-‐delay links, such as satellite links.
Placement of EPP probes Probes for measuring EPP parameters shall be placed inside or close to Registrars points of access to the Internet across the different geographic regions; care shall be taken not to deploy probes behind high propagation-‐delay links, such as satellite links.
Tolerance Average net mass of cement packed in bags in a sample shall be equal to or more than 50kg. If and as desired by the Engineer-in-Charge, the number of samples to be checked for net mass of cement per bag, in a given number of bags shall be as given below: 100 to 150 bags : 20 sample 150 to 280 bags : 32 sample 281 to 500 bags : 50 sample 501 to 1200 bags : 80 sample 1201 to 3200 bags : 125 sample 3201 and above : 200 sample The bags in a sample shall be selected at random. B- Sand (Fine Aggregate)
Technical Specifications The Technical Specifications furnished on the CD are intended to establish the standards for quality, performance and technical requirements for all labor, workmanship, material, methods and equipment necessary to complete the Work. When specifications and drawings are provided or referenced by the County, these are to be considered part of the Scope of Work, and to be specifically documented in the Detailed Scope of Work. For convenience, the County supplied specifications, if any, and the Technical Specifications furnished on the CD.
Placement of RDDS probes Probes for measuring RDDS parameters shall be placed inside the networks with the most users across the different geographic regions; care shall be taken not to deploy probes behind high propagation-‐delay links, such as satellite links.
Displacements Employees displaced for one of the reasons (1-9) listed in 9.4 will be placed on a "displaced list". Employees on the displaced list will be placed before new hires are appointed provided there are qualified employees on the displaced list for the vacant position. Effort will be made to identify and place involuntarily transferred employees within a radius no more than the current distance they drive to work or 25 miles, whichever is greater. Refusal by the employee to accept a position shall release the Board from further obligation to that employee. It will be necessary for displaced employees to provide an address and telephone number where they can be contacted during summer break to the Director of Employee Relations. Each displaced employee will receive a letter from their principal/supervisor that outlines the displacement procedure. LAYOFFS:
TRANSPORTATION, TRAVEL TIME AND ROOM AND BOARD 14.01 The Employer shall remunerate employees for travel time and mileage as follows:
Cooking The University will permit cooking only in the designated kitchen areas of the University Housing. In all other areas, cooking is permitted only with University approved appliances. The following appliances are prohibited: toaster ovens, microwave ovens larger than 800 xxxxx, refrigerators larger than 4.2 cubic feet, gas grills, steamers and any open-flame cooking device or heating unit. For a complete list please reference the Residential Handbook.
