Principal dimensions Sample Clauses

Principal dimensions. 4.2.1. The principal dimensions of the side impact dummy (including the suit), based on Figure 2 of this annex, are given in Table 3 of this annex. The dimensions are measured without suit Figure 2 Measurements for principal dummy dimensions (See Table 3) Table 3 Principal Dummy Dimensions No. Parameter Dimension (mm) 1 Sitting height 909 ± 9 2 Seat to shoulder joint 565 ± 7 3 Seat to lower face of thoracic spine box 351 ± 5 4 Seat to hip joint (centre of bolt) 100 ± 3 5 Sole to seat, sitting 442 ± 9 6 Head width 155 ± 3 7 Shoulder/arm width 470 ± 9 8 Thorax width 327 ± 5 9 Abdomen width 290 ± 5 10 Pelvis width 355 ± 5 11 Head depth 201 ± 5 12 Thorax depth 276 ± 5 13 Abdomen depth 199 ± 5 14 Pelvis depth 240 ± 5 15 Back of buttocks to hip joint (centre of bolt) 155 ± 5 16 Back of buttocks to front knee 606 ± 9 5. Certification of the dummy
Sample 1Sample 2Sample 3See All (9)
AutoNDA by SimpleDocs
Principal dimensions. Figure 2 - Main dimensions of dummy Table 2 - Q-dummy dimensions No. Q0 Q1 Q1.5 Q3 Q6 Q10 (design targets) Dimensions in mm 17 Seating height (head tilted forward) 355±9 479±9 499±9 544±9 601±9 < 748±9 18 Shoulder height (sitting) 225±7 298±7 309±7 329±7 362±7 473±7 Stature (head tilted forward) - 740±9 800±9 985±9 1143±9 < 1443±9 5 Chest depth - 114±5 113±5 146±5 141±5 171±5 15 Shoulder width 230±7 227±7 227±7 259±7 305±7 334.8±7 13 Neck diameter 44 61.91 61.91 61.91 61.91 58.02 76.03 65.01 85.94 12 Hip width - 191±7 194±7 200±7 223±7 270±7 1 Back of buttocks to front of knees 130±5 211±5 235±5 305±5 366±5 4885.4±5 2 Back of buttocks to popliteus - 161±5 185±5 253±5 299±5 4184.9±5 21 Thigh height, sitting 69 72 79 92 114 Height of spacer device for positioning of dummy5 1/ 173±2 229±2 237±2 250±2 270±2 359±2
Sample 1Sample 2Sample 3See All (5)
Principal dimensions. 4.2.1. The principal dimensions of the side impact dummy (including the suit), based on figure 2 of this annex, are given in table 3 of this annex. Figure 2 - Measurements for principal dummy dimensions (see table 3) No. Table 3 - Principal Dummy Dimensions Parameter Dimension (mm) 1 Sitting height 904 ± 7 2 Seat to shoulder joint 557 ± 5 3 Seat to bottom lower rib 357 ± 5 4 Seat to arm 242 ± 5 5 Seat to H-point 98 ± 2 6 Sole to seat, sitting 456 ± 5 7 H-point to head c.o.g. 687 ± 5 8 H-point to centre upper rib 393 ± 3 9 H-point to centre middle rib 337 ± 3 10 H-point to centre lower rib 281 ± 3 11 H-point to centre abdominal force transducer 180 ± 3 12 H-point to centre pubic symphysis force transducer 14 ± 2 13 Head width 154 ± 2 14 Shoulder/arm width 482 ± 5 15 Thorax width 330 ± 5 16 Abdomen width 290 ± 5 17 Pelvis width 355 ± 5 18 Neck diameter 80 ± 2 19 Head depth 201 ± 5 20 Thorax depth 276 ± 5 21 Abdomen depth 204 ± 5 22 Pelvis depth 245 ± 5 23 Back of buttocks to H-point 157 ± 2 24 Back of buttocks to front knee 610 ± 5 5. CERTIFICATION OF THE DUMMY
Sample 1Sample 2
Principal dimensions. 1. Pontoons (Two) Length Overall 310’-0” Breadth Overall 226’-0” Breadth Overall including anchor racks 253’ 10” Depth of Mid-body 24’-0” Depth at Ends 27’-0” Width (Each) 56’-0”
Sample 1
Principal dimensions. 3.2.1. The principal dimensions, based on figure 1 of this annex, are given in table 2. Annex 8 - Appendix 1 11 2 1 15 7 13 6 4 12 16 17 Principal dimensions of manikin 14 18 19 Figure 1 Table 2 No. Dimensions Dimensions in mm by age group 9 months 3 years 6 years 10 years 1 Back of buttocks to front knee 195 334 378 456 2 Back of buttocks to popliteus, sitting 145 262 312 376 3 Centre of gravity to seat 180 190 190 200 4 Chest circumference 440 510 580 660 5 Chest depth 102 125 135 142 6 Distance between shoulder blades 170 215 250 295 7 Head width 000 000 000 141 8 Head length 166 174 175 181 9 Hip circumference, sitting 510 590 668 780 10 Hip circumference, standing (not shown) 470 550 628 740 11 Hip depth, sitting 125 147 168 180 12 Hip width, sitting 166 206 229 255 13 Neck width 60 71 79 89 14 Seat to elbow 135 153 155 186 15 Shoulder width 216 249 295 345 16 Eye height sitting 000 000 000 625 17 Height, sitting 450 560 636 725 18 Shoulder height, sitting 280 335 403 483 19 Sole to popliteus, sitting 125 205 283 355 20 Stature (not shown) 708 980 1 166 1 376 21 Thigh height, sitting 70 85 95 106 4. Adjustment of joints
Sample 1

Related to Principal dimensions

  • Components Patheon will purchase and test all Components (with the exception of Client-Supplied Components) at Patheon’s expense and as required by the Specifications.

  • Configuration The configuration for the Purchase Right Aircraft will be the Detail Specification for Model 767-3S2F aircraft at the revision level in effect at the time of the Supplemental Agreement. Such Detail Specification will be revised to include (i) changes required to obtain required regulatory certificates and (ii) other changes as mutually agreed upon by Boeing and Customer.

  • Temperature Where low temperature and/or self-service cases are used for any of such merchandise coming under the jurisdiction of the Union, such cases shall be served only by employees covered by this Agreement.

  • Weights light, moderate and heavy, have their normal everyday meanings, and are to be applied consistently, regardless of the physical characteristics of the jobholder and whether the duties are normally carried out by women or by men; or by small people or large people; or by fit or unfit people. So, a sack of cement or a sack of potatoes is a heavy weight, even if it is lifted and carried without obvious exertion by a tall, fit, young person.

  • Projects There shall be a thirty (30) km free zone around the projects excluding the Metro Vancouver Area. For local residents, kilometers shall be paid from the boundary of the free zone around the project. Workers employed by any contractor within an identified free zone who resides outside of that same free zone will be paid according to the Kilometer Chart from the project to their residence less thirty

  • Substantial Completion “Substantial Completion” means the stage in the progress of the Work when the Work, or designated portions thereof, may still require minor modifications or adjustments but, in the Owner’s opinion, the Work has progressed to the point such that all parts of the Work under consideration are fully operational and usable for intended purposes, as evidenced by a Certificate of Substantial Completion approved by the Owner. If a Certificate of Occupancy is required by public authorities having jurisdiction over the Work, said certificate shall be issued before the Work or any portion thereof is considered substantially complete. When the Contractor considers that the Work, or a portion thereof which the Owner agrees to accept separately, is substantially complete, the Contractor shall notify Owner’s Designated Representative (sometimes referred to as the “ODR”) and request a determination as to whether the Work or designated portion thereof is substantially complete. If the ODR does not consider the Work substantially complete, the ODR will notify the Contractor giving reasons therefore. Failure on the Owner’s part to list a reason does not alter the responsibility of the Contractor to complete all Work in accordance with the terms of this Agreement. After satisfactorily completing items identified by Owner’s Designated Representative, the Contractor shall then submit another request for the ODR to determine Substantial Completion. If The ODR considers the Work substantially complete, The ODR will prepare and deliver a certificate of Substantial Completion which shall establish the date of Substantial Completion, shall include a punch list of items to be completed or corrected before final completion and final payment, shall establish the time within which the Contractor shall finish the punch list, and shall establish responsibilities of the Owner and the Contractor for security, maintenance, heat, utilities, damage to the Work, warranty and insurance. Failure to include an item on the punch list does not alter the responsibility of the Contractor to complete all Work in accordance with the terms and conditions of this Agreement. The certificate of Substantial Completion shall be signed by the Owner and the Contractor to evidence acceptance of the responsibilities assigned to them in such certificate. Substantial Completion (as defined in this agreement) for all stages of the Work shall be achieved on or before the following Substantial Completion date: DATE FOR SUBSTANTIAL COMPLETION: TBD Under no circumstances will the time for Substantial Completion exceed this date without a written amendment to this Agreement. THE TIMES SET FORTH IN THE CONSTRUCTION DOCUMENTS ARE AN ESSENTIAL ELEMENT OF THE AGREEMENT. TIME LIMITS STATED IN THE CONTRACT DOCUMENTS ARE OF THE ESSENCE OF THIS AGREEMENT.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!