Submittals None Sample Clauses

Submittals None. Specifications Contractor shall provide labor, materials and equipment to replace the current three (3) Worthington pump assemblies with Government furnished Aurora model 413 pump assemblies. Scope of work shall include the following: Transport three (3) Aurora Model 413 pumps from US Moorings at 0000 XX Xx Xxxxxx Xx, Xxxxxxxx XX 00000 to Contractor’s facility for installation. Remove three existing Central Service salt water pumps located in lower pump room near forward bulkhead and discard as scrap. Scrap existing foundations and flush off to platform. Fabricate three new foundations for mounting new pumps. New pumps shall be located in same location as current. Coat foundations to original paint schedule. Install new pumps. Modify existing inlet and outlet salt water piping to accommodate new pumps. Modify existing pressure gauge and flushing lines to attach to new pumps. Verify existing cable is sufficient in size and length for new motors. Connect existing electrical cables and bump motors to check rotation.
Sample 1Sample 2
AutoNDA by SimpleDocs
Submittals None. 06. Specifications a. Remove to pier port AND starboard pipe pieces 176 in upper pump room. See reference a. Provide and install 3 / 4 inch thick A36 steel plate flange to close hole in bulkhead, use existing bolt holes to secure in place, creating soft patches, blast and coat steel plate. Crop out 26 inch port and starboard skin plate penetrations, piece 178, on the well deck forward of the trunnion davits. Insert openings in skin plate with plate and xxxxxxxxxx.xx match surround plate. Also eliminate 2 port and 2 starboard flushing line skin plate penetrations near pieces 178 and insert skin plate. Remove dredge pipe supports on well deck b. Remove hydraulic lines that served port AND starboard #11 valves that were removed. See reference a. Remove exterior hydraulic piping and supports to 6 inches from bulkhead. Remove exterior hydraulic piping and supports from 6 inches from bulkhead to where the lines join the main hydraulic runs. Cap the lines coming from the hydraulic skids. Plug or cap lines at bulkhead penetration to make water tight. c. Provide pipe supports near the bottoms of pipe pieces #3 and #4 in lower pump room. See reference a. They shall be 80 inches above the walking surface. Uses 1/2 inch x 4 inch bar for the band and 4 x 4 x 3/8 angle for the struts. Each pipe shall have a strut running outboard to the bulkhead xxxxxxxxx and a strut running aft to the bulkhead xxxxxxxxx. These supports are required to safely remove the upper and lower 156 elbows during dredge pipe inspection and repairs. d. Remove intact to dock starboard piece number 151 e. Remove intact to dock sluice valve number 7 starboard. Remove flushing water line, cropping it back to mainline and cap or plug. Operational test cap or plug. f. Remove intact to dock starboard piece number 15. g. Remove intact to dock starboard piece number 149 h. Remove intact to dock starboard piece number 152 i. Remove intact to dock starboard piece number 153 j. Move flange currently attached to wye piece 149 to close opening created in piece 161 k. Provide and install cover flange to keep debris out of starboard inboard dredge pump l. Transport all removed dredge pipe and fittings to the US Government Moorings warehouse except the #178 pieces. Note that Port and Starboard #11 valves and adjoining flex joints shown in E1740-35 have already been removed. m. Remove sluice valve #1 from lower level Engine Room. Provide and install blind flanges to both pipe flanges left after removal of valve. n....
Sample 1
Submittals None. Specifications
Sample 1

Related to Submittals None

  • Submittals Submittals required by the Contract Documents shall be prepared specifically for the Work by the Contractor to illustrate some portion of the Work. Submittals are not Contract Documents.

  • Submittal Reports, plans, surveys, field notes, original drawings, computer tapes, graphic files, tracings, calculations, analyses, reports, specifications, data, sketches and/or schematics prepared by A/E and supporting documents (collectively referred to hereinabove and hereinafter as the "A/E Work Product(s)"), shall be submitted by A/E on or before the dates specified for completion, as set out in the Production Schedule set forth in Exhibit C.

  • Order to Stop Work The Chief Procurement Officer, may, by written order to Contractor at any time, and without notice to any surety, require Contractor to stop all or any part of the work called for by this contract. This order shall be for a specified period not exceeding 90 days after the order is delivered to Contractor, unless the parties agree to any further period. Any such order shall be identified specifically as a stop work order issued pursuant to this clause. Upon receipt of such an order, Contractor shall forthwith comply with its terms and take all reasonable steps to minimize the occurrence of costs allocable to the work covered by the order during the period of work stoppage. Before the stop work order expires, or within any further period to which the parties shall have agreed, the Chief Procurement Officer shall either: i. cancel the stop work order; or, ii. terminate the work covered by such order as provided in the Termination for Default clause or the Termination for Convenience clause of this contract.

  • SUBMITTAL LABEL All submittals, should use the hard-copy label below and place on front of their outermost sealed envelope/package. Company : Contact Name: Contact Phone/ Email: Address: CONTACT: IFB NUMBER: TITLE: BID DUE DATE: ORANGE COUNTY PROCUREMENT DIVISION INTERNAL OPERATIONS CENTRE II 000 X. XXXXX XXXXXX, 2ND FLOOR ORLANDO, FL 32801.

  • Construction Change Directives 1.1.1, 3.4.2, 3.11, 3.12.8, 4.2.8, 7.1.1, 7.1.2, 7.1.3, 7.3, 9.3.1.1 Construction Schedules, Contractor’s 3.10, 3.11, 3.12.1, 3.12.2, 6.1.3, 15.1.6.2

  • Submittal Schedule Within sixty days after the Effective Date of the Contract, the Contractor shall prepare and submit a Submittal Schedule for review and approval of the Design Professional. In establishing the Submittal Schedule the Contractor shall take into account large submittal documents that will require longer review times, e.g., submittals with over fifty sheets of drawings. The Design Professional’s approval shall be based on conformance of the Submittal Schedule with the Overall Project Schedule, subject to change from time to time in accordance with the progress of the Work.

  • Change Orders Any alteration or deviation from the Services mentioned or any other contractual specifications that result in a revision of this Agreement shall be executed and attached to this Agreement as a change order (“Change Order”).

  • CERTIFICATION OF NO ASBESTOS CONTAINING MATERIALS OR WORK 8.1 The Contractor shall be responsible for ensuring that no asbestos containing materials or work is included within the scope of the Work. The Contractor shall take whatever measures it deems necessary to insure that all employees, suppliers, fabricators, material men, subcontractors, or their assigns, comply with this requirement. 8.2 The Contractor shall ensure that Texas Department of Health licensed individuals, consultants or companies are used for any required asbestos work including asbestos inspection, asbestos abatement plans/specifications, asbestos abatement, asbestos project management and third-party asbestos monitoring.

  • Construction Plans Tenant shall prepare final plans and specifications for the Tenant Improvements that (a) are consistent with and are logical evolutions of the Approved Schematic Plans and (b) incorporate any other Tenant-requested (and Landlord-approved) Changes (as defined below). As soon as such final plans and specifications ("Construction Plans") are completed, Tenant shall deliver the same to Landlord for Landlord's approval, which approval shall not be unreasonably withheld, conditioned or delayed. All such Construction Plans shall be submitted by Tenant to Landlord in electronic .pdf, CADD and full-size hard copy formats, and shall be approved or disapproved by Landlord within ten (10) business days after delivery to Landlord. Landlord's failure to respond within such ten (10) business day period shall be deemed approval by Landlord. If the Construction Plans are disapproved by Landlord, then Landlord shall notify Tenant in writing of its objections to such Construction Plans, and the parties shall confer and negotiate in good faith to reach agreement on the Construction Plans. Promptly after the Construction Plans are approved by Landlord and Tenant, two (2) copies of such Construction Plans shall be initialed and dated by Landlord and Tenant, and Tenant shall promptly submit such Construction Plans to all appropriate Governmental Authorities for approval. The Construction Plans so approved, and all change orders approved (to the extent required) by Landlord, are referred to herein as the "Approved Plans."

  • Construction Progress Schedule A schedule indicating proposed activity sequences and durations, milestone dates for receipt and approval of pertinent information, preparation, submittal, and processing of Shop Drawings and Samples, delivery of materials or equipment requiring long-lead time procurement, and proposed date(s) of Material Completion and Occupancy and Final Completion. The schedule will be developed to represent the sixteen or seventeen CSI Specification Divisions. It shall have a minimum number of activities as required to adequately represent to Owner the complete scope of work and define the Project’s critical path and associated activities. If the Project is to be phased, then each individual Phase should be identified from start through completion of the overall Project and should be individually scheduled and described, including any Owner’s occupancy requirements and showing portions of the Project having occupancy priority. The format of the schedule will have dependencies indicated on a monthly grid identifying milestone dates such as construction start, phase construction, structural top out, dry-in, rough-in completion, metal stud and drywall completion, equipment installation, systems operational, Material Completion and Occupancy Date, final inspection dates, Punchlist, and Final Completion date.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!