Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.
Bullying and Harassment Neither DFMC nor you will engage in behaviour that is, or may be reasonably considered to be, intimidating, bullying or harassing or commit any act or behaviour which is offensive or abusive in connection with this Contract. If you are in breach of this clause, DFMC may suspend the collection of your milk for a period of 5 days or until such time as DFMC determines (acting reasonably) that the behaviour has been rectified.
TRAINING AND RELATED MATTERS The parties recognise that in order to increase the efficiency and productivity of the company a significant commitment to structured training and skill development is required. Accordingly the parties commit themselves to: a) The parties to this Agreement recognise the importance of the apprenticeship system to the construction industry. It is agreed that every employer party to this Agreement who employs five (5) or more tradespersons in any one classification shall undertake to employ at least one (1) apprentice or make arrangements to host an apprentice from an agreed group apprenticeship scheme. Where an employer does not currently have an apprentice as per this provision, reasonable time shall be allowed to enable the employer to comply with this clause. Further, the parties are committed to a strong ratio of apprentices in the industry. Apprenticeship levels on a specific project may be discussed at the Project Pre-Commencement Conference (refer Clause 16). b) Providing employees with the opportunity to acquire additional skills within relevant career path structures through appropriate structured training based on nationally endorsed (i.e. Construction Training Australia endorsed) competency standards and curriculum; c) Actively encouraging employees to seek formal recognition of their skills (i.e. recognition of prior learning); and d) Using training providers accredited and acceptable to the parties. The CFMEU, MBAV and other employer associations are legitimately engaged in providing training to industry and it is hereby agreed that all parties will properly recognise and accept the validity of nationally accredited training as provided by the other parties. e) The parties will consult on the development of training programs which are consistent with the following: • Training provided will be consistent with the company’s business requirements, relevant to the work of the employees, consistent with the skills development of each employee and with applicable national competency standards. • Training may be taken either on or off the job with all reasonable steps being taken to conduct training in normal working hours. • If an approved training activity is undertaken during ordinary working hours, the employee/s concerned shall not suffer any loss of pay. • Approved training activities undertaken outside of ordinary hours will be paid at single time or will, at the employee’s option, be taken as time off in lieu of payment. Provided that the scheduling of time off must be consistent with the needs of the business and be by agreement with the company. • Training costs of courses approved by the company will be met by the company. • The company will not be asked to meet the costs of training undertaken by employees which was not approved by the company. • Leave of absence granted pursuant to this clause shall count as service for all purposes of the award and this agreement. • Accredited members of the union will be allowed up to 5 days per year, without loss of pay, to attend trade union educational courses conducted or approved by the union. (see appendix H) f) The parties to this Agreement recognise the importance of the role that Apprentices/Trainees fulfill within the industry and, more importantly, a role that they will fulfill as trades persons following the conclusion of the indentures. To this end the Victorian Building Industry Consultative Committee will investigate ways of enhancing employment prospects for Apprentice/Trainees. In addition it is agreed that, where appropriate, employers will use their best endeavours to employ Apprentices/Trainees in order to ensure appropriate trade persons levels for the future.
Training and Education SECTION 1 – Law Enforcement Supervisors’ Training
Professional Engineering and Architect’s Services Professional Engineering and Architect’s Services are not permitted to be provided under this Agreement. Texas statutes prohibit the procurement of Professional Engineering and Architect’s Services through a cooperative agreement.
Packing and Marking All material and equipment to be furnished by the Contractor shall be packed, crated or otherwise suitably protected to withstand shipment undamaged to the destination. Each package, crate or part shall be marked plainly with the name of the consignee, shipping destination, the Owner's order number, and such other markings as are required. Complete packing lists, one copy with each package and two (2) copies by mail to the Owner at time of shipment, shall be supplied showing contents and identity of each package.
DRUG AND ALCOHOL FREE WORKPLACE 20.1 All employees must report to work in a condition fit to perform their assigned duties unimpaired by alcohol or drugs.
CUTTING AND PATCHING The Contractor shall be responsible for cutting, fitting or patching required to complete the Work or to make its parts fit together properly.
Skidding and Yarding Methods of skid- ding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and construction clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. B6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees desig- nated for cutting.
Training and Professional Development 11.1 The Employer will develop and maintain an employee training and development plan and provide such plan to the Union upon request. Staff training is intended to provide an opportunity for classified staff employees for training sponsored by the University Training and Development and the UW Medical Centers Organizational Development and Training. Education/Professional Leave is intended to facilitate employee access to continuing education opportunities. Training and educational/professional leave may be used for the purpose of improving job performance, maintaining and increasing proficiency, preparing staff for greater responsibility, or increasing promotional opportunities within the framework of staff positions available at the University. 11.2 Any release time for training for employees accepted for such classes shall be in accordance with the Executive Order (currently No. 52) governing this matter. In the event that two or more employees request the same training period and supervision must limit the number of persons who may participate at one time due to work requirements, the selection will be made on a mutually agreeable basis within the department. 11.3 The training program is a proper subject for discussion by either departmental or University-wide Joint Union/Management Committees. 11.4 If the Employer requires an employee to receive training, reimbursement will be provided in accordance with the University travel rules. Employee attendance at Employer required training, either during or outside working hours, will be considered time worked and compensated in accordance with the provisions of this Agreement. 11.5 Employee attendance at training not required by the Employer and not covered by Executive Order 52, either on approved leave from or outside of working hours, will be voluntary and not considered time worked.
