Welding/Cutting Torch Use Sample Clauses

Welding/Cutting Torch Use. No welding or cutting torch is to be used in the Building without the prior approval of Landlord. If such approval is granted by Landlord, the General Contractor must have a fire extinguisher present in the Work Area at all times when the equipment is being used. Additionally, the General Contractor must perform any such work after-hours because of the fumes which may be associated with such welding/cutting torch usage.
AutoNDA by SimpleDocs
Welding/Cutting Torch Use. No welding/cutting torch or arc welding equipment is to be used in the Building without prior approval of Project Manager. If such approval is granted by Building Management, the general contractor must have a fire extinguisher present in the Work Area at all times when the equipment is being used. Additionally, the Tenant and its general contractor may be required to perform all such work during non-Business Hours because of the fumes which may be associated with such welding. Tenant and its general contractor shall take efforts to protect life safety system from activating, and if a false alarm is signaled, Tenant will be charged $1,000.00 for each incident.
Welding/Cutting Torch Use. At no time is any welding, cutting torch or any open flame tool to be used in the Building without prior approval from Management. If approval is granted, the Contractor must coordinate the timing with the Management Office and Engineering Manager and must have an appropriate fire extinguisher present in the work area at all times that the equipment is in use.
Welding/Cutting Torch Use. No welding, burning or cutting torch work is to be performed at the Project Site without the prior approval of Owner. If such approval is granted by Owner, the Contractor must have a firewatch, fire blankets, and a fire extinguisher present in the Work Area at all times when the equipment is being used. Additionally, the Contractor may, at Owner’s request, be required to perform any such work after-hours because of the fumes which may be associated with such welding/cutting torch usage. AFDOCS//21459967
Welding/Cutting Torch Use. At no time is any welding, cutting torch, or any open flame tool to be used in the building without prior approval in the form of a Hot Work Permit. Hot Work Permits can be obtained from the Landlord’s Representative. If approval is granted, the contractor must coordinate the timing with the Landlord’s Representative, twenty-four (24) hours before the work begins, then must have an appropriate fire extinguisher present in the work area at all times that the equipment is in use.

Related to Welding/Cutting Torch Use

  • Participating TO’s Interconnection Facilities The Participating TO shall design, procure, construct, install, own and/or control the Participating TO’s Interconnection Facilities described in Appendix A at the sole expense of the Interconnection Customer. Unless the Participating TO elects to fund the capital for the Participating TO’s Interconnection Facilities, they shall be solely funded by the Interconnection Customer.

  • Scope of Interconnection Service 1.3.1 The NYISO will provide Energy Resource Interconnection Service and Capacity Resource Interconnection Service to Interconnection Customer at the Point of Interconnection. 1.3.2 This Agreement does not constitute an agreement to purchase or deliver the Interconnection Customer’s power. The purchase or delivery of power and other services that the Interconnection Customer may require will be covered under separate agreements, if any, or applicable provisions of NYISO’s or Connecting Transmission Owner’s tariffs. The Interconnection Customer will be responsible for separately making all necessary arrangements (including scheduling) for delivery of electricity in accordance with the applicable provisions of the ISO OATT and Connecting Transmission Owner’s tariff. The execution of this Agreement does not constitute a request for, nor agreement to, provide Energy, any Ancillary Services or Installed Capacity under the NYISO Services Tariff or any Connecting Transmission Owner’s tariff. If Interconnection Customer wishes to supply or purchase Energy, Installed Capacity or Ancillary Services, then Interconnection Customer will make application to do so in accordance with the NYISO Services Tariff or Connecting Transmission Owner’s tariff.

  • Software Use Case Red Hat Enterprise Linux Developer Suite Subscription Services for Red Hat Enterprise Linux Developer Suite are available for Development Purposes only.

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CSTC chooses to subtend a Verizon access Tandem, CSTC’s NPA/NXX must be assigned by CSTC to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG. 9.2.2 CSTC shall establish Access Toll Connecting Trunks pursuant to applicable access Tariffs by which it will provide Switched Exchange Access Services to Interexchange Carriers to enable such Interexchange Carriers to originate and terminate traffic to and from CSTC’s Customers. 9.2.3 The Access Toll Connecting Trunks shall be two-way trunks. Such trunks shall connect the End Office CSTC utilizes to provide Telephone Exchange Service and Switched Exchange Access to its Customers in a given LATA to the access Tandem(s) Verizon utilizes to provide Exchange Access in such LATA. 9.2.4 Access Toll Connecting Trunks shall be used solely for the transmission and routing of Exchange Access to allow CSTC’s Customers to connect to or be connected to the interexchange trunks of any Interexchange Carrier which is connected to a Verizon access Tandem.

  • Equipment Use Lessee agrees that the Equipment will be operated by competent, qualified personnel in connection with Lessee's business for the purpose for which the Equipment was designed and in accordance with applicable operating instructions, laws, and government regulations, and that Lessee shall use all reasonable precautions to prevent loss or damage to the Equipment from fire and other hazards. Lessee shall procure and maintain in effect all orders, licenses, certificates, permits, approvals, and consents required by federal, state, or local laws or by any governmental body, agency, or authority in connection with the delivery, installation, use, and operation of the Equipment.

  • System Upgrade Facilities and System Deliverability Upgrades Connecting Transmission Owner shall design, procure, construct, install, and own the System Upgrade Facilities and System Deliverability Upgrades described in Appendix A hereto. The responsibility of the Developer for costs related to System Upgrade Facilities and System Deliverability Upgrades shall be determined in accordance with the provisions of Attachment S to the NYISO OATT.

  • Start-Up and Synchronization Consistent with the mutually acceptable procedures of the Developer and Connecting Transmission Owner, the Developer is responsible for the proper synchronization of the Large Generating Facility to the New York State Transmission System in accordance with NYISO and Connecting Transmission Owner procedures and requirements.

  • Master Use The Licensor hereby grants to Licensee a non-exclusive license (this "License) to record vocal synchronization to the Composition partly or in its entirety and substantially in its original form ("Master Recording")

  • Interconnection Facilities Engineering Procurement and Construction Interconnection Facilities, Network Upgrades, and Distribution Upgrades shall be studied, designed, and constructed pursuant to Good Utility Practice. Such studies, design and construction shall be based on the assumed accuracy and completeness of all technical information received by the Participating TO and the CAISO from the Interconnection Customer associated with interconnecting the Large Generating Facility.

  • Purpose of Interconnection Facilities Except as may be required by Applicable Laws and Regulations, or as otherwise agreed to among the Parties, the Interconnection Facilities shall be constructed for the sole purpose of interconnecting the Large Generating Facility to the Participating TO’s Transmission System and shall be used for no other purpose.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!