WORK JURISDICTION. 4.01 It is agreed by the parties to this Agreement that all work specified in Article Four shall be performed exclusively by Elevator Constructor Mechanics and Elevator Constructor Helpers in the employ of the Employer. 4.02.01 The handling and unloading of all equipment coming under the jurisdiction of the Elevator Constructor from the time such equipment arrives at or near the building site shall be handled and unloaded by the Elevator Constructors. Mechanical equipment such as a fork lift or truck mounted swing boom may be used by the Elevator Constructors. A xxxxxxx or crane can be used under the supervision of Elevator Constructors to handle and unload the heavy material described in Paragraph 4.05.0l. 4.02.02 The erecting and assembling of all elevator equipment to wit: electric hydraulic, steam, belt, dumb-waiters, residence elevators, parking garage elevators (such as Xxxxxx, Pigeon Hole, or similar types of elevators), compressed air and handpower and all types of equipment covered by Elevator Safety Codes. 4.02.03 It is understood and agreed that the preassembly of all escalators, moving stairways, and link belt carriers, that may be done in the factory shall include the following: 1. Truss or truss sections with tracks, drive units, machines, handrail drive sheaves, drive chains, step chains and steps installed and permanently aligned. 2. Balustrade brackets may be shipped attached but not aligned. 3. Setting of all controllers and all wiring and conduit from the controller. 4.02.04 All wiring, conduit, and raceways from main line feeder terminals on the controller to other elevator apparatus and operating circuits. Controllers are not to be shipped from the factory with extended wiring attached thereto. 4.02.05 The erecting of all guide rails. 4.02.06 The installation of all grating and counterweight screens, overhead work, either wood or iron, and all material used for mounting of elevator apparatus in machine room, overhead or below. 4.02.07 The drilling of overhead beams for attaching machines, sheaves, kick angles, and all other elevator equipment. 4.02.08 The setting of all templates. 4.02.09 All foundations, whether of wood or metal, that should take the place of masonry. 4.02.10 The assembly of all cabs complete. 4.02.11 The installation of all indicators. 4.02.12 The erecting of all electrical or mechanical automatic or semiautomatic gates complete. 4.02.13 The hanging of all automatic or semi-automatic elevator hoistway doors, together with the installation of hangers and tracks. 4.02.14 The installation of all devices for opening and closing, and locking of elevator car and hoistway doors and gates. 4.02.15 The drilling of doors for mounting of closing devices. 4.02.16 The drilling of angle supports for mounting of closing devices except one template hole. 4.02.17 The drilling of xxxxx for sill trips. 4.02.18 The operating of all temporary and uncompleted cars. 4.02.19 The setting of all elevator pressure open or pit tanks. 4.02.20 The setting of hydraulic power units (power units include: motor, pump, drive valve system, internal piping, muffler, internal wiring, controller and tank). Where power units arrive in parts, they shall be assembled at the job site. The wiring and piping to and between multiple hydraulic power units shall be performed at the job site. 4.02.21 All air cushions with the exception of those built of brick or those put together with hot rivets. 4.03.01 Nothing contained in Article Four shall preclude an employer from preassembling and prefabricating the following: 1. Temporary elevators 2. Residence elevators 3. Dumbwaiters
Appears in 2 contracts
Samples: Collective Agreement, Collective Agreement
WORK JURISDICTION. 4.01 It is agreed by the parties to this Agreement that all work specified in Article Four shall be performed exclusively by Elevator Constructor Mechanics and Elevator Constructor Helpers in the employ of the Employer.
4.02.01 The handling and unloading of all equipment coming under the jurisdiction of the Elevator Constructor from the time such equipment arrives at or near the building site shall be handled and unloaded by the Elevator Constructors. Mechanical equipment such as a fork lift or truck mounted swing boom may be used by the Elevator Constructors. A xxxxxxx or crane xxxxx can be used under the supervision of Elevator Constructors to handle and unload the heavy material described in Paragraph 4.05.0l.
4.02.02 The erecting and assembling of all elevator equipment to wit: electric hydraulic, steam, belt, dumb-waiters, residence elevators, parking garage elevators (such as Xxxxxx, Pigeon Hole, or similar types of elevators), compressed air and handpower and all types of equipment covered by Elevator Safety Codes.
4.02.03 It is understood and agreed that the preassembly of all escalators, moving stairways, and link belt carriers, that may be done in the factory shall include the following:
1. Truss or truss sections with tracks, drive units, machines, handrail drive sheaves, drive chains, step chains and steps installed and permanently aligned.
2. Balustrade brackets may be shipped attached but not aligned.
3. Setting of all controllers and all wiring and conduit from the controller.
4.02.04 All wiring, conduit, and raceways from main line feeder terminals on the controller to other elevator apparatus and operating circuits. Controllers are not to be shipped from the factory with extended wiring attached thereto.
4.02.05 The erecting of all guide rails.
4.02.06 The installation of all grating and counterweight screens, overhead work, either wood or iron, and all material used for mounting of elevator apparatus in machine room, overhead or below.
4.02.07 The drilling of overhead beams for attaching machines, sheaves, kick angles, and all other elevator equipment.
4.02.08 The setting of all templates.
4.02.09 All foundations, whether of wood or metal, that should take the place of masonry.
4.02.10 The assembly of all cabs complete.
4.02.11 The installation of all indicators.
4.02.12 The erecting of all electrical or mechanical automatic or semiautomatic gates complete.
4.02.13 The hanging of all automatic or semi-automatic elevator hoistway doors, together with the installation of hangers and tracks.
4.02.14 The installation of all devices for opening and closing, and locking of elevator car and hoistway doors and gates.
4.02.15 The drilling of doors for mounting of closing devices.
4.02.16 The drilling of angle supports for mounting of closing devices except one template hole.
4.02.17 The drilling of xxxxx for sill trips.
4.02.18 The operating of all temporary and uncompleted cars.
4.02.19 The setting of all elevator pressure open or pit tanks.
4.02.20 The setting of hydraulic power units (power units include: motor, pump, drive valve system, internal piping, muffler, internal wiring, controller and tank). Where power units arrive in parts, they shall be assembled at the job site. The wiring and piping to and between multiple hydraulic power units shall be performed at the job site.
4.02.21 All air cushions with the exception of those built of brick or those put together with hot rivets.
4.03.01 Nothing contained in Article Four shall preclude an employer from preassembling and prefabricating the following:
1. Temporary elevators 2. Residence elevators 3. Dumbwaiters
Appears in 2 contracts
Samples: Collective Agreement, Collective Agreement
WORK JURISDICTION. 4.01 It is agreed by the parties to this Agreement that all work specified in Article Four shall be performed exclusively by Elevator Constructor Mechanics and Elevator Constructor Helpers in the employ of the Employer.
4.02.01 The handling and unloading of all equipment coming under the jurisdiction of the Elevator Constructor from the time such equipment arrives at or near the building site shall be handled and unloaded by the Elevator Constructors. Mechanical equipment such as a fork lift or truck mounted swing boom may be used by the Elevator Constructors. A xxxxxxx or crane xxxxx can be used under the supervision of Elevator Constructors to handle and unload the heavy material described in Paragraph 4.05.0l4.04.0l.
4.02.02 The erecting and assembling of all elevator equipment to wit: electric hydraulic, steam, belt, dumb-waiters, residence elevators, parking garage elevators (such as Xxxxxx, Pigeon Hole, or similar types of elevators), compressed air and handpower and all types of equipment covered by Elevator Safety Codes.
4.02.03 It is understood and agreed that the preassembly of all escalators, moving stairways, and link belt carriers, that may be done in the factory shall include the following:
1. Truss or truss sections with tracks, drive units, machines, handrail drive sheaves, drive chains, step chains and steps installed and permanently aligned.
2. Balustrade brackets may be shipped attached but not aligned.
3. Setting of all controllers and all wiring and conduit from the controller.
4.02.04 All wiring, conduit, and raceways from main line feeder terminals on the controller to other elevator apparatus and operating circuits. Controllers are not to be shipped from the factory with extended wiring attached thereto.
4.02.05 The erecting of all guide rails.
4.02.06 The installation of all grating and counterweight screens, overhead work, either wood or iron, and all material used for mounting of elevator apparatus in machine room, overhead or below.
4.02.07 The drilling of overhead beams for attaching machines, sheaves, kick angles, and all other elevator equipment.
4.02.08 The setting of all templates.
4.02.09 All foundations, whether of wood or metal, that should take the place of masonry.
4.02.10 The assembly of all cabs complete.
4.02.11 The installation of all indicators.
4.02.12 The erecting of all electrical or mechanical automatic or semiautomatic gates complete.
4.02.13 The hanging of all automatic or semi-automatic elevator hoistway doors, together with the installation of hangers and tracks.
4.02.14 The installation of all devices for opening and closing, and locking of elevator car and hoistway doors and gates.
4.02.15 The drilling of doors for mounting of closing devices.
4.02.16 The drilling of angle supports for mounting of closing devices except one template hole.
4.02.17 The drilling of xxxxx for sill trips.
4.02.18 The operating of all temporary and uncompleted cars.
4.02.19 The setting of all elevator pressure open or pit tanks.
4.02.20 The setting of hydraulic power units (power units include: motor, pump, drive valve system, internal piping, muffler, internal wiring, controller and tank). Where power units arrive in parts, they shall be assembled at the job site. The wiring and piping to and between multiple hydraulic power units shall be performed at the job site.
4.02.21 All air cushions with the exception of those built of brick or those put together with hot rivets.
4.03.01 Nothing contained in Article Four shall preclude an employer from preassembling and prefabricating the following:
1. Temporary elevators 2. Residence elevators 3. Dumbwaiters
Appears in 1 contract
Samples: Collective Agreement
WORK JURISDICTION. 4.01 It is agreed by the parties to this Agreement that all work specified in Article Four shall be performed exclusively by Elevator Constructor Mechanics and Elevator Constructor Helpers in the employ of the Employer.
4.02.01 The handling and unloading of all equipment coming under the jurisdiction of the Elevator Constructor from the time such equipment arrives at or near the building site shall be handled and unloaded by the Elevator Constructors. Mechanical equipment such as a fork lift or truck mounted swing boom may be used by the Elevator Constructors. A xxxxxxx or crane can be used under the supervision of Elevator Constructors to handle and unload the heavy material described in Paragraph 4.05.0l.xxxxx
4.02.02 The erecting and assembling of all elevator equipment to wit: electric hydraulic, steam, belt, dumb-waiters, residence elevators, parking garage elevators (such as Xxxxxx, Pigeon Hole, or similar types of elevators), compressed air and handpower and all types of equipment covered by Elevator Safety Codes.
4.02.03 It is understood and agreed that the preassembly of all escalators, moving stairways, and link belt carriers, that may be done in the factory shall include the following:
1. Truss or truss sections with tracks, drive units, machines, handrail drive sheaves, drive chains, step chains and steps installed and permanently aligned.
2. Balustrade brackets may be shipped attached but not aligned.
3. Setting of all controllers and all wiring and conduit from the controller.
4.02.04 All wiring, conduit, and raceways from main line feeder terminals on the controller to other elevator apparatus and operating circuits. Controllers are not to be shipped from the factory with extended wiring attached thereto.
4.02.05 The erecting of all guide rails.
4.02.06 The installation of all grating and counterweight screens, overhead work, either wood or iron, and all material used for mounting of elevator apparatus in machine room, overhead or below.
4.02.07 The drilling of overhead beams for attaching machines, sheaves, kick angles, and all other elevator equipment.
4.02.08 The setting of all templates.
4.02.09 All foundations, whether of wood or metal, that should take the place of masonry.
4.02.10 The assembly of all cabs complete.
4.02.11 The installation of all indicators.
4.02.12 The erecting of all electrical or mechanical automatic or semiautomatic gates complete.
4.02.13 The hanging of all automatic or semi-automatic elevator hoistway doors, together with the installation of hangers and tracks.
4.02.14 The installation of all devices for opening and closing, and locking of elevator car and hoistway doors and gates.
4.02.15 The drilling of doors for mounting of closing devices.
4.02.16 The drilling of angle supports for mounting of closing devices except one template hole.
4.02.17 The drilling of xxxxx for sill trips.
4.02.18 The operating of all temporary and uncompleted cars.
4.02.19 The setting of all elevator pressure open or pit tanks.
4.02.20 The setting of hydraulic power units (power units include: motor, pump, drive valve system, internal piping, muffler, internal wiring, controller and tank). Where power units arrive in parts, they shall be assembled at the job site. The wiring and piping to and between multiple hydraulic power units shall be performed at the job site.
4.02.21 All air cushions with the exception of those built of brick or those put together with hot rivets.
4.03.01 Nothing contained in Article Four shall preclude an employer from preassembling and prefabricating the following:
1. Temporary elevators 2. Residence elevators 3. Dumbwaiters
Appears in 1 contract
Samples: Collective Agreement
WORK JURISDICTION. 4.01 It is agreed by the parties to this Agreement that all work specified in Article Four shall be performed exclusively by Elevator Constructor Mechanics and Elevator Constructor Helpers in the employ of the Employer.
4.02.01 The handling and unloading of all equipment coming under the jurisdiction of the Elevator Constructor from the time such equipment arrives at or near the building site shall be handled and unloaded by the Elevator Constructors. Mechanical equipment such as a fork lift forklift or truck mounted swing boom may be used by the Elevator Constructors. A xxxxxxx or crane xxxxx can be used under the supervision of Elevator Constructors to handle and unload the heavy material described in Paragraph 4.05.0l4.04.0l.
4.02.02 The erecting and assembling of all elevator equipment to wit: electric hydraulic, steam, belt, dumb-waiters, residence elevators, parking garage elevators (such as Xxxxxx, Pigeon Hole, or similar types of elevators), compressed air and handpower and all types of equipment covered by Elevator Safety Codes.
4.02.03 It is understood and agreed that the preassembly of all escalators, moving stairways, and link belt carriers, that may be done in the factory shall include the following:
1. Truss or truss sections with tracks, drive units, machines, handrail drive sheaves, drive chains, step chains and steps installed and permanently aligned.
2. Balustrade brackets may be shipped attached but not aligned.
3. Setting of all controllers and all wiring and conduit from the controller.
4.02.04 All wiring, conduit, and raceways from main line feeder terminals on the controller to other elevator apparatus and operating circuits. Controllers are not to be shipped from the factory with extended wiring attached thereto.
4.02.05 The erecting of all guide rails.
4.02.06 The installation of all grating and counterweight screens, overhead work, either wood or iron, and all material used for mounting of elevator apparatus in machine room, overhead or below.
4.02.07 The drilling of overhead beams for attaching machines, sheaves, kick angles, and all other elevator equipment.
4.02.08 The setting of all templates.
4.02.09 All foundations, whether of wood or metal, that should take the place of masonry.
4.02.10 The assembly of all cabs complete.
4.02.11 The installation of all indicators.
4.02.12 The erecting of all electrical or mechanical automatic or semiautomatic gates complete.
4.02.13 The hanging of all automatic or semi-automatic elevator hoistway doors, together with the installation of hangers and tracks.
4.02.14 The installation of all devices for opening and closing, and locking of elevator car and hoistway doors and gates.
4.02.15 The drilling of doors for mounting of closing devices.
4.02.16 The drilling of angle supports for mounting of closing devices except one template hole.
4.02.17 The drilling of xxxxx for sill trips.
4.02.18 The operating of all temporary and uncompleted cars.
4.02.19 The setting of all elevator pressure open or pit tanks.
4.02.20 The setting of hydraulic power units (power units include: motor, pump, drive valve system, internal piping, muffler, internal wiring, controller and tank). Where power units arrive in parts, they shall be assembled at the job site. The wiring and piping to and between multiple hydraulic power units shall be performed at the job site.
4.02.21 All air cushions with the exception of those built of brick or those put together with hot rivets.
4.03.01 Nothing contained in Article Four shall preclude an employer from preassembling and prefabricating the following:
1. Temporary elevators 2. Residence elevators 3. Dumbwaiters
Appears in 1 contract
Samples: Collective Agreement
