Special Provisions Check if Required ✔ If checked, the Supplemental State Terms and attached hereto as Exhibit “G” are hereby incorporated by reference into this DPA in their entirety. ✔ If checked, the Provider, has signed Exhibit “E” to the Standard Clauses, otherwise known as General Offer of Privacy Terms
Initial Provisions Establishment of a Free Trade Area
CFR PART 200 Contract Provisions Explanation Required Federal contract provisions of Federal Regulations for Contracts for contracts with ESC Region 8 and TIPS Members: The following provisions are required to be in place and agreed if the procurement is funded in any part with federal funds. The ESC Region 8 and TIPS Members are the subgrantee or Subrecipient by definition. Most of the provisions are located in 2 CFR PART 200 - Appendix II to Part 200—Contract Provisions for Non-Federal Entity Contracts Under Federal Awards at 2 CFR PART 200. Others are included within 2 CFR part 200 et al. In addition to other provisions required by the Federal agency or non-Federal entity, all contracts made by the non- Federal entity under the Federal award must contain provisions covering the following, as applicable.
Remedial Provisions Each Grantor covenants and agrees with the Administrative Agent and the other Secured Parties that, from and after the date of this Agreement until the Discharge of Obligations:
Final Provisions Clause 16
Transitional Provisions 24.1. As from the official date of entry into force of the 01 series of amendments to this Regulation, no Contracting Party applying this Regulation shall refuse to grant or refuse to accept type approval under this Regulation as amended by the 01 series of amendments. 24.2. As from 12 months after the date of entry into force of the 01 series of amendments to this Regulation, Contracting Parties applying this Regulation shall grant approvals only if the type of components to be approved meets the requirements of Part I of this Regulation as amended by the 01 series of amendments to this Regulation. 24.3. Type approvals of components other than fuel rail, as defined in paragraph 4.72., granted according to the original version of this Regulation or of components granted according to the 01 series of amendments, shall remain valid and shall be accepted for the purpose of their installation on vehicles as long as the requirements for the specific component have not changed by any series of amendments. 24.4. As from 18 months after the date of entry into force of the 01 series of amendments to this Regulation, Contracting Parties applying this Regulation shall grant approvals only if the vehicle type to be approved meets the requirements of Part II of this Regulation as amended by the 01 series of amendments to this Regulation. 24.5. Until 12 months after the date of entry into force of the 01 series of amendments to this Regulation, Contracting Parties applying this Regulation can continue to grant type approvals for the type of components to the original version of this Regulation without taking into account the provisions of the 01 series of amendments. 24.6. Until 18 months after the date of entry into force of the 01 series of amendments to this Regulation, Contracting Parties applying this Regulation can continue to grant type approvals for the vehicle type to the original version of this Regulation without taking into account the provisions of the 01 series of amendments. 24.7. Notwithstanding the provisions of paragraphs 24.5. and 24.6., Contracting Parties applying this Regulation shall not refuse to grant extensions of type approvals for existing types of component or vehicle types which have been issued according to this Regulation without taking into account the provisions of the 01 series of amendments to this Regulation. 24.8. As from the official date of entry into force of the 02 series of amendments to this Regulation, no Contracting Party applying this Regulation shall refuse to grant or refuse to accept type approval under this Regulation as amended by the 02 series of amendments. 24.9. As from 1 September 2017 Contracting Parties applying this Regulation shall grant approvals only if the type of components to be approved meets the requirements of Part I of this Regulation as amended by the 02 series of amendments to this Regulation. 24.10. As from 1 September 2018 Contracting Parties applying this Regulation shall grant approvals only if the vehicle type to be approved meets the requirements of Part II of this Regulation as amended by the 02 series of amendments to this Regulation. 24.11. As from 1 September 2019 Contracting Parties applying this Regulation may refuse to recognize approvals of a type of vehicle which have not been granted in accordance with Part II of this Regulation as amended by the 02 series of amendments to this Regulation. 24.12. Contracting Parties applying this Regulation shall not refuse to grant extensions of type approvals for existing types of component or vehicle types which have been issued according to this Regulation without taking into account the provisions of the 02 series of amendments to this Regulation. 24.13. Notwithstanding paragraphs 24.11. and 24.12., Contracting Parties applying this Regulation shall continue to accept type approvals granted to the preceding series of amendments, which are not affected by the 02 series of amendments.
Country-Specific Provisions Argentina
of the Technical Provisions The Project Schedule shall be used by the Parties for planning and monitoring the progress of the Work and as the basis for determining the amount of monthly progress payments to be made to DB Contractor.
SPECIAL PROVISION The failure of the COUNTY to insist upon the strict performance of any provision of this Agreement or to exercise any right based upon breach thereof or the acceptance of any performance during such breach shall not constitute a waiver of any right under this Agreement.
BASIC PROVISIONS A. Employer's Name: [....] Address: [....] B. The Employer is a ( ) corporation; ( ) S Corporation; ( ) partnership; ( ) Sole Proprietor; ( ) Other: [....] C. Employer's Tax ID Number: [....]
