Method C definition

Method C means the calculation method set out in this paragraph.
Sample 1Sample 2Sample 3
Method C means the calculation method set out in...
Sample 1Sample 2
Method C. The payment institution’s own funds shall amount to at least the relevant indicator defined in points (1) and (2), multiplied by the multiplication factor defined in point (3) and by the scaling factor k defined in the fifth paragraph.
Sample 1

Examples of Method C in a sentence

  • Lignin Sulfonate and magnesium chloride shall be applied when the top 1 inch of Traveled Way contains not less than 3 percent moisture, nor more than 120 percent of optimum moisture as determined by AASHTO T-99, Method C.

  • Prior to applying DO-6BA, DO-6PA, or DO-8, the top 2 inches of Traveled Way shall contain not less than 80 percent nor more than 120 percent of optimum moisture as determined by AASHTO T-99, Method C.

  • Method A, Method B, Method C and Method D shall be used for acceptance as specified in Section 401 - Hot Mix Asphalt Pavements.

  • Prior to applying DO-6BA, DO-6PA, or DO-8 the top 2 inches of Traveled Way shall contain not less than 80 percent nor more than 120 percent of optimum moisture as determined by AASHTO T-99, Method C.

  • Lignin Sulfonate and magnesium chloride shall be applied when the top 1 inch of Traveled Way contains not less than 3 percent moisture nor more than 120 percent of optimum moisture as determined by AASHTO T-99, Method C.

  • TABLE 9: TABLE OF GRADATION COMPOSITE " f " FACTORS (Methods A and B) Constituent For HMA evaluated under Acceptance Method C, the Department will determine a pay factor using acceptance limits from Table 7: Method C Acceptance Limits.

  • T104-99 (R2003).........Soundness of Aggregate by Use of Sodium Sulfate or Magnesium Sulfate T180-01 (R2004).........Moisture-Density Relations of Soils using a 4.54 kg (10 lb.) Rammer and a 457 mm (18 in.) Drop T191-02(R2006)..........Density of Soil In-Place by the Sand-Cone Method C.

  • Should a difference of opinion arise as to what does or does not constitute Extra Work, or as to the payment therefor, and the ENGINEER insists upon its performance, the CONTRACTOR shall proceed with the work after making written request for written order and shall keep an accurate account of the “actual field cost” thereof, as provided under Method (C).

  • Method C: Water bar roadbed at locations staked on the ground and construct as SHOWN ON THE DRAWINGS or as included in SUPPLEMENTAL SPECIFICATIONS.

  • Should a difference of opinion arise as to what does or does not constitute Extra Work, or as to the payment therefore, and Engineer insists upon its performance, Contractor shall proceed with the Work after making its written request for written authorization to Engineer and shall keep an accurate account of the “actual field cost” thereof, as provided under Method (C).


More Definitions of Method C

Method C. For a vehicle tested in an indoor facility, shall be located with the front plane of the vehicle on the PP' line as shown in Figure 2a of the Appendix to this annex. The vehicle shall maintain a constant test speed, vtest for at least 5 seconds. For constant speed test condition of 10 km/h, the test speed vtest shall be 10 km/h ±1 + 2 km/h. The measured values are valid for the nominal speed of 10 km/h. For constant speed test condition of 20 km/h, the test speed vtest shall be 20 km/h ± 1 + 2 km/h. The measured values are valid for the nominal speed of 20 km/h. For automatic transmission vehicles, the gear selector shall be placed as specified by the manufacturer for normal driving. For manual transmission vehicles, the gear selector shall be placed in the highest gear which can achieve the target vehicle speed with constant engine speed.
Sample 1
Method C. For a vehicle tested in an indoor facility, shall be located with the rear plane of the vehicle on the PP' line as shown in Figure 2b of the Appendix to this annex. The vehicle shall maintain a constant test speed, vtest for at least 5 seconds. For constant speed test condition of 6 km/h, the test speed vtest shall be 6 km/h ± 2 km/h. For automatic transmission vehicles, the gear selector shall be placed as specified by the manufacturer for normal reverse driving. For manual transmission vehicles, the gear selector shall be placed in the highest reverse gear which can achieve the target vehicle speed with constant engine speed.
Sample 1

Related to Method C

  • Alternative method means any method of sampling and analyzing for an air pollutant that is not a reference or equivalent method but that has been demonstrated to the satisfaction of the commissioner and the U.S. EPA to, in specific cases, produce results adequate for a determination of compliance.

  • Settlement Method means, with respect to any conversion of Notes, Physical Settlement, Cash Settlement or Combination Settlement, as elected (or deemed to have been elected) by the Company.

  • Procedure means one or more surgical procedures or medical therapy performed in a Center of Excellence.

  • Semi-annual (2/Year) sampling frequency means the sampling shall be done during the months of June and December, unless specifically identified otherwise.

  • Standard Methods means the examination and analytical procedures set forth in the most recent edition of "Standard Methods for the Examination of Water and Wastewater" published jointly by the American Public Health Association, the American Water Works Association, and the Water Pollution Control Federation.

  • Yearly (1/Year) sampling frequency means the sampling shall be done in the month of September, unless specifically identified otherwise in the effluent limitations and monitoring requirements table.

  • Process weight means the total weight of all materials introduced into any source operation. Solid fuels charged will be considered as part of the process weight, but liquid and gaseous fuels and combustion air will not.