Nominal Power Output definition

Nominal Power Output means the original manufactured nameplate specification of power in the Module (Maximum Power, Pmax), expressed in Xxxxx, and measured at STC, excluding any specified positive tolerance. ① Air mass 1.5, ② Irradiance 1000W/m2, ③ Cell Temperature 25℃ Jinko provides the Limited Warranty set forth herein commencing upon the earlier of one of the following dates:

Nominal Power Output means the power output measured for the Modules under the Standard Test Conditions, as indicated on its original nameplate, excluding any positive tolerance that may exist in the Modules.

Nominal Power Output. (PO0)” means the original manufactured nameplate specification of the Module, expressed in Xxxxx, as certified by Xxxxx and indicated on the Module, excluding any specified positive tolerance. “Actual Power Output (POt)” means the power output of the Module, expressed in Xxxxx, at Watt peak that a Module generates or, for a Bifacial Module, that the front-side of a Bifacial Module generates, at a given point in time in a year after the Warranty Start Date (t) in its ‘Maximum Power Point’ under Standard Test Conditions, corrected for any measurement error (“STC”). STC are as follows, measured in accordance with IEC 61215: (a) light spectrum of AM 1.5; (b) an irradiation of 1000W per m2; and (c) a cell temperature of 25 degrees centigrade at right angle irradiation. The “Degradation Rate (DR)” shall be any positive amount calculated in accordance with the following formula, expressed as a percent:

Examples of Nominal Power Output in a sentence

• Nominal Power Output in product datasheet is the power in Watt peak that a Photovoltaic Solar Modules generates in its Maximum Power Point under Standard Testing Conditions (STC).

• Nominal Power Output (PO0)” means the original manufactured nameplate specification of the Module, expressed in Watts, as certified by Sunergy and indicated on the Module, excluding any specified positive tolerance.

• Ulica Solar warrants that for a period of 25 years commencing on the WARRANTY START DATE loss of power output of the Nominal Power Output specified in the relevant product data sheet and measured at standard test conditions (STC) for the products shall not exceed:⚫ For Mono-crystalline panels: 2.0% in the first year, thereafter 0.55% per year, ending with 84.8% in the 25th year after the WARRANTY START DATE.

• Power Output Degradation shall not exceed 2% in the first year beginning from the Warranty Start Date, and an additional 0.55% each year thereafter from the beginning of the second year until that date which is twenty-five (25) years following the Warranty Start Date, at which time the Peak Power Output shall be not less than 84.8% of the Nominal Power Output.

More Definitions of Nominal Power Output

Nominal Power Output. (PO0)” means the original manufactured nameplate specification of the Module, expressed in Xxxxx, as certified by Xxxxx and indicated on the Module, excluding any specified positive tolerance. “Actual Power Output (POt)” means the power output of the Module, expressed in Xxxxx, at Watt peak that a Module generates (or, for BIFACIAL SERIES, that the front- side of a Module generates) at a given point in time in a year after the Warranty Start Date (t) in its ‘Maximum Power Point’ under Standard Test Conditions, corrected for any measurement error (“STC”). STC are as follows, measured in accordance with IEC 61215: (a) light spectrum of AM 1.5; (b) an irradiation of 1000W per m2; and

Nominal Power Output. (PO0)” means the original manufactured nameplate specification of the Module, expressed in Xxxxx, as certified by Xxxxx and indicated on the Module, excluding any specified positive tolerance. “Actual Power Output (POt)” means the power output of the Module, expressed in Xxxxx, at Watt peak that a Module generates at a given point in time in a year after the Warranty Start Date (t) in its ‘Maximum Power Point’ under Standard Test Conditions, corrected for any measurement error (“STC”). STC are as follows, measured in accordance with IEC 61215: (a) light spectrum of AM 1.5; (b) an irradiation of 1000W per m2; and (c) a cell temperature of 25 degrees centigrade at right angle irradiation. The “Degradation Rate (DR)” shall be any positive amount calculated in accordance with the following formula, expressed as a percent:

Nominal Power Output. (PO0)” means the original manufactured nameplate specification of the Module, expressed in Xxxxx, as certified by Xxxxx and indicated on the Module, excluding any specified positive tolerance. “Actual Power Output (POt)” means the power output of the Module, shall be disclosed in writing to both Parties prior to performance of any such tests and shall be reflected in any final test results provided by the Independent Testing Lab. The determination by an Independent Testing Lab as to whether a breach has occurred shall be final and conclusive with respect to the matters covered by such determination. Jinko shall be responsible for all costs incurred by it in connection with the shipment by Customer of a Module pursuant to Section 5(i) hereto and any Independent Testing Lab’s services provided pursuant to this Section 5, including shipping, testing services, storage, insurance and any Module destruction incidental thereto; provided, however, Customer shall promptly upon receipt of notice indemnify Jinko for all such costs on a dollar-for-dollar basis in the event the Independent Testing Lab is unable to confirm a breach of the Warranties or, if no Independent Testing Lab was utilized, Customer is otherwise unable to establish a breach of the Warranties.

Nominal Power Output means the original manufactured nameplate specification of the Module, expressed in Xxxxx, as certified by Pixon and indicated on the Module, excluding any specified positive tolerance.