Floor Finishing Sample Clauses

Floor Finishing. The job of floor finishing includes the cleaning and applying of finish to hard floor surfaces per industry standards.
Sample 1Sample 2Sample 3See All (5)
AutoNDA by SimpleDocs
Floor Finishing. Marble/Vitrified Tiles in all floor with 6” height skirting to all room. Kitchen and Bath and W.C floor shall be of ceramic tiles.
Sample 1Sample 2
Floor Finishing. Floor finish must be applied in a thin, even coat. The number of coats applied will depend on the use and condition of the floor but in no case will be less than two coats be applied. At the stated frequencies in Attachment D, floors must be wet mopped between regular floor finishing operations. The floor must be properly swept free of all loose dirt prior to mopping. Upon completion of wet mopping, the floor must be clean and free of dirt, water streaks, mop marks and properly rinsed, and dry mopped to present a clean appearance. All surfaces must be dry with corners, cracks, and splice joints clean after wet mopping.
Sample 1
Floor Finishing. 1 Finish concrete floor surfaces in accordance with CAN3-A23.1M.
Sample 1
Floor Finishing.  All floor refinishing, whether new floors or old, shall be announced to the Property Manager at least three days in advance of the day of the anticipated work.  Unit owner doing the floor work must contact each resident within the floor of construction and the floor above to notify them of the pending work.  All windows and doors must remain fully open until all odors from the product have dissipated.  It is recommended that floor finishing not be conducted on Fridays.
Sample 1
Floor Finishing. Painted floors in buildings Xxxxx with plastic carpet Raised floor
Sample 1
Floor Finishing. The job of floor finishing includes the cleaning and applying of finish to asphalt, rubber, vinyl and linoleum floors. (a) Sweeping: Sweep floors thoroughly. Remove all gum and adhesive materials. (b) Stripping: Remove all old finishes or wax from floors, using a concentrated solution of liquid cleaner. Cleaner is to be applied with a mop, and scrubbed with an electrical polishing machine with scrub brush or a medium grade-scrubbing pad. Extremely stubborn spots, gum, rust, burns, etc. shall be removed by hand with a scouring pad dipped in the cleaning solution. Corners and other areas that the polishing machine cannot reach shall be scrubbed and thoroughly cleaned by hand. Care shall be exercised so that baseboards, walls and furniture shall not be splashed or marred. Cleaning solution shall be taken up with a mop or a water pickup and the floor rinsed twice with clean water to remove all traces of cleaning solution. Do not flood floor with water; use only enough water as required for good rinsing. Floor shall be allowed to dry thoroughly after rinsing.
Sample 1
AutoNDA by SimpleDocs
Floor Finishing 
Sample 1

Related to Floor Finishing

  • Fabrication Making up data or results and recording or reporting them.

  • Irrigation An irrigation reduced pressure zone (hereinafter referred to as “RPZ”) is required for any irrigation systems and must be installed by the Developer and/or eventual lot owner and tested in accordance with the Minnesota Department of Health Guidelines for Designing Backflow Prevention Assembly Installations (hereinafter referred to as “Guidelines”). The initial test results and certification shall be submitted to the City of Maple Grove Public Works Department. Subsequently, the RPZ must be tested, per the Guidelines, at least annually by a certified tester with the results reported to the City of Maple Grove Building Department and the RPZ must be rebuilt as needed in accordance with the Guidelines. Test/rebuilt reports shall be mailed or faxed to the City of Maple Grove Building Department at (000) 000-0000. The irrigation system shall be designed, and the Plans shall be modified accordingly, prior to the issuance of any permits for the development of the Property, to accommodate a 1-inch water meter and a maximum flow of 50 gallons per minute.

  • Cleaning 8.1 CONTRACTOR shall, at his own expenses, at all times keep the premises free from accumulation of debris, waste materials, and rubbish, and at the completion of the work, he shall remove his tools and equipment and all surplus materials, debris, waste material, and rubbish and shall leave the premises in a neat and clean condition. If CONTRACTOR does not attend to such cleaning immediately upon request, OWNER shall have the right to have this work done by others and deduct the cost therefore from the payment due CONTRACTOR hereunder.

  • Equipment Cleaning (a) Areas, known by Forest Service prior to timber sale advertisement, that are infested with invasive species of concern are shown on Sale Area Map. A current list of invasive species of concern and a map showing the extent of known infestations is available at the Forest Supervisor’s Office. For purposes of this provision, “Off-Road Equipment” includes all logging and construction machinery, except for log trucks, chip vans, service vehicles, water trucks, pickup trucks, cars, and similar vehicles.

  • Floor Load Tenant shall not place a load upon any floor of the Premises that exceeds 50 pounds per square foot “live load”. Landlord reserves the right to reasonably designate the position of all Equipment which Tenant wishes to place within the Premises, and to place limitations on the weight thereof.

  • Walls 12 Developer shall provide rustication patterns on all walls, except drainage headwalls, in Aesthetic 13 Area 3 in accordance with Exhibit L2.24 of the LAADCR. The final designs shall resemble these 14 simulations.

  • Landscaping 3.9.1 All plant material shall conform to the Canadian Nursery Landscape Association’s Canadian Nursery Stock Standard (ninth edition or newer). 3.9.2 There shall be an opaque wood fence or masonry wall at least 1.8 metres tall along the eastern property line extending the length of the surface parking area and access to the underground parking area as generally shown on Schedule B. 3.9.3 Prior to the issuance of a Development Permit, the Developer agrees to provide Landscape Plan that comply with the provisions of this section. The Landscape Plan shall be prepared by a Landscape Architect (a full member, in good standing with Canadian Society of Landscape Architects) and comply with all provisions of this section. 3.9.4 Prior to issuance of the first Occupancy Permit the Developer shall submit to the Development Officer a letter prepared by a member in good standing of the Canadian Society of Landscape Architects certifying that all landscaping has been completed according to the terms of this Development Agreement. 3.9.5 Notwithstanding Section 3.9.4, where the weather and time of year do not allow the completion of the outstanding landscape works prior to the issuance of the Occupancy Permit, the Developer may supply a security deposit in the amount of 110 percent of the estimated cost to complete the landscaping. The cost estimate is to be prepared by a member in good standing of the Canadian Society of Landscape Architects. The security shall be in favour of the Municipality and shall be in the form of a certified cheque or automatically renewing, irrevocable letter of credit issued by a chartered bank. The security shall be returned to the Developer only upon completion of the work as described herein and illustrated on the Schedules, and as approved by the Development Officer. Should the Developer not complete the landscaping within twelve months of issuance of the Occupancy Permit, the Municipality may use the deposit to complete the landscaping as set out in this section of the Agreement. The Developer shall be responsible for all costs in this regard exceeding the deposit. The security deposit or unused portion of the security deposit shall be returned to the Developer upon completion of the work and its certification. 3.9.6 All landscape areas designed to be installed upon any portion of the building must be supported by documentation from a Structural Engineer indicating that the building design is able to support any required drainage or additional weight caused by the landscaped area.

  • Provisioning Line Splitting and Splitter Space 3.8.1 The Data LEC, Voice CLEC or BellSouth may provide the splitter. When Southern Telecom or its authorized agent owns the splitter, Line Splitting requires the following: a non-designed analog Loop from the serving wire center to the NID at the End User’s location; a collocation cross connection connecting the Loop to the collocation space; a second collocation cross connection from the collocation space connected to a voice port; the high frequency spectrum line activation, and a splitter. The Loop and port cannot be a Loop and port combination (i.e. UNE-P), but must be individual stand-alone Network Elements. When BellSouth owns the splitter, Line Splitting requires the following: a non designed analog Loop from the serving wire center to the NID at the End User’s location with CFA and splitter port assignments, and a collocation cross connection from the collocation space connected to a voice port. 3.8.2 An unloaded 2-wire copper Loop must serve the End User. The meet point for the Voice CLEC and the Data LEC is the point of termination on the MDF for the Data LEC's cable and pairs. 3.8.3 The foregoing procedures are applicable to migration to Line Splitting Service from a UNE-P arrangement, BellSouth Retail Voice Service, BellSouth High Frequency Spectrum (CO Based) Line Sharing. 3.8.4 For other migration scenarios to line splitting, BellSouth will work cooperatively with CLECs to develop methods and procedures to develop a process whereby a Voice CLEC and a Data LEC may provide services over the same Loop.

  • Configuration The configuration for the Purchase Right Aircraft will be the Detail Specification for Model 767-3S2F aircraft at the revision level in effect at the time of the Supplemental Agreement. Such Detail Specification will be revised to include (i) changes required to obtain required regulatory certificates and (ii) other changes as mutually agreed upon by Boeing and Customer.

  • Spares Boeing will revise, as applicable, the customized Recommended Spares Parts List (RSPL) and Illustrated Parts Catalog (IPC).

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!