Foundation In their respective agreements, the parties have recommended that a temporary manpower/resource pool of permanent employees be set up to cover normal absences (Section 20 of the Agreement). The parties agree that the employees working in such a pool can also be used to cover peak activities or in other temporary situations that call for extra xxxxxxx.
Alignment with Modernization Foundational Programs and Foundational Capabilities The activities and services that the LPHA has agreed to deliver under this Program Element align with Foundational Programs and Foundational Capabilities and the public health accountability metrics (if applicable), as follows (see Oregon’s Public Health Modernization Manual, (xxxx://xxx.xxxxxx.xxx/oha/PH/ABOUT/TASKFORCE/Documents/public_health_modernization_man ual.pdf):
Foundations nor shall the Contractor be responsible for correction of leaks resulting from said failure.
University Any notice may be served upon the University by delivering it, in writing, to the University at the address set forth on the last page of this Agreement, by depositing it in a United States Postal Service deposit box with the postage fully prepaid and with the notice addressed to the University at the aforementioned address, or by sending a facsimile of it to the University facsimile number set forth on the last page of this Agreement.
NO HARDSTOP/PASSIVE LICENSE MONITORING Unless an Authorized User is otherwise specifically advised to the contrary in writing at the time of order and prior to purchase, Contractor hereby warrants and represents that the Product and all Upgrades do not and will not contain any computer code that would disable the Product or Upgrades or impair in any way its operation based on the elapsing of a period of time, exceeding an authorized number of copies, advancement to a particular date or other numeral, or other similar self-destruct mechanisms (sometimes referred to as “time bombs,” “time locks,” or “drop dead” devices) or that would permit Contractor to access the Product to cause such disablement or impairment (sometimes referred to as a “trap door” device). Contractor agrees that in the event of a breach or alleged breach of this provision that Authorized User shall not have an adequate remedy at law, including monetary damages, and that Authorized User shall consequently be entitled to seek a temporary restraining order, injunction, or other form of equitable relief against the continuance of such breach, in addition to any and all remedies to which Authorized User shall be entitled.
Millwright Xxxxx be to assist and work under the direction and instructions I or A. He will work alone at times performing assignments in keeping with his training. During the course of his year, training must become proficient in good practices in the areas of fitting, aligning, lubricating and the operation of all shop tools and machines. In addition to the foregoing, he will be exposed to and the process of learning techniques required in trouble shooting key production machinery, pipe fitting, basic welding and machining but not be expected to display a high degree of proficiency in these areas at this point. Millwright Must be capable of performing the tasks of fittings, aligning, lubricating an able to operate all shop tools and machines. Must under direction become proficient in basic welding and pipe fitting as well as dismantling and reassembly of plant equipment. Under direction,will continueto develop skills in trouble shooting all plant equipment and improve his skills at machining part and be exposed to basic principles of hydraulics and pneumatic. He may work alone frequently, but occasionally will require direction and instructions form Millwright I or A. Millwright 11: be capable, without direction of fitting, aligning and lubrication and taking apart and reassembling plant equipment. In addition, is expected to be able to weld, operate shop tools and do pipe fitting as required. Must under direction, become proficient at effective methods of trouble shooting and repairing hydraulic, pneumatic and mechanical faults in plant machinery. I: Must be capable without direction of performing all practices under Xxxxxxxxxx Must under directionbecomeproficient at reading and understanding blueprints, all phases of installing new equipment, laying out hydraulic and mechanical drives and meet speed and power requirements correctly. Xxxxxxxxxx "A": Must he capable without direction, of performing all under Xxxxxxxxxx X, and Must take full responsibility for work done by himself or his assistant. Must he in possession of a Millwright Certificate or a Machinist Certificate or Welder Certificate. Millwrightspresently employed in this classification will not be required to have a Certificate.
Washtenaw Community College Eastern Michigan University Xxxxxx Xxxxxxxxxx College of Engineering & Technology Student Services BE 214 xxx_xxxxxxxx@xxxxx.xxx; 734.487.8659 734.973.3398
Technology Transfer Subject to the terms of the Development Supply Agreement, as soon as reasonably practicable, but in no event later than the fifth (5th) anniversary of the Effective Date, Alnylam shall initiate a technology transfer to MedCo, or to its Third Party manufacturer(s) of Licensed Product, selected by MedCo and reasonably acceptable to Alnylam, of Alnylam Know-How that is reasonably necessary or useful for the Manufacture of the Licensed Product, and shall make available its personnel on a reasonable basis to consult with MedCo or such Third Party manufacturer(s) with respect thereto, all at MedCo’s expense, including the Costs reasonably incurred by Alnylam in connection with such technology transfer activities. MedCo shall reimburse Alnylam such Costs incurred with respect to such Manufacturing technology transfer within [***] days after receipt of an invoice therefor. Alnylam and its Affiliates shall keep complete and accurate records in sufficient detail to enable the payments payable hereunder to be determined. Alnylam shall not be required to perform technology transfer to more than one Third Party manufacturer for each stage of the Licensed Product supply chain (i.e., Bulk Drug Substance, Bulk Drug Product and Finished Product). Promptly after MedCo’s written request, Alnylam shall use Commercially Reasonable Efforts to assign to MedCo any manufacturing agreement between Alnylam and a Third Party that is solely related to the manufacture of Licensed Products. Such assignment shall be subject to the terms and conditions of such agreement, including any required consents of such Third Party and MedCo’s written agreement to assume all the obligations of Alnylam under such agreement to be undertaken after such assignment, but Alnylam shall remain solely responsible for its obligations under such agreement arising prior to such assignment. Except as provided in the immediately preceding sentence, MedCo shall be solely responsible for contracting with such Third Party manufacturer (and any other Third Party manufacture to whom Alnylam has initiated technology transfer as set forth in this Section 5.3) for the supply of such Licensed Product and Alnylam shall have no obligations under such agreement between MedCo and such Third Party manufacturer. Alnylam shall use Commercially Reasonable Efforts to obtain any such consent in a form reasonably acceptable to MedCo.
Nonsectarian Charter School shall be nonsectarian in its programs, admissions policies, employment practices and all other operations.
Joint Network Implementation and Grooming Process Upon request of either Party, the Parties shall jointly develop an implementation and grooming process (the “Joint Grooming Process” or “Joint Process”) which may define and detail, inter alia:
